® 4x4 Component w/Audio Matrix EXT-COMPAUD-44424 User Manual www.gefen.com w ww.gefen.
ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday PST Write To: Gefen LLC. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen Inc. reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice. 4x4 Component w/Audio Matrix is a trademark of Gefen LLC. © 2011 Gefen LLC.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Panel Layout 5 Connecting And Operating The 4x4 Component w/Audio Matrix 6 RMT-16-IR Remote Installation 7 IR Channel Configuration 8 RS-232 Serial Control Interface 9 Rack Mount Installation 10 Specifications 11 Warranty
INTRODUCTION Congratulations on your purchase of the 4x4 Component w/Audio Matrix. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 4X4 COMPONENT W/AUDIO MATRIX • The 4x4 Component Audio Matrix is housed in a metal box for better RF shielding. • The 4x4 Component Audio Matrix works with all component displays.
FEATURES Features • switches easily between any four component/audio sources • Sends up to four video inputs to any four remote displays • Maintains 1080p, and 2k resolution video • Discrete IR remote (included) • Serial RS-232 remote port (for unattended control) • Rack ears included Package Includes (1) 4x4 Component w/Audio Matrix (4) 6-foot 5 RCA Component Audio/Video cables (1) 24V DC Power Supply (1) Rack Ears (1) IR Remote (1) User Manual 3
4 Component & Analog/Digital Audio Output 2 Component & Analog/Digital Audio Output 1 Display 1 LED Source Indicator and selector button RS232 Controller Port Power Indicator and Power button IR Sensor Display 3 LED source Indicator and selector button Component & Analog/Digital Audio input 1 Component & Analog/Digital Audio Input 3 Display 4 LED Source Indicator and selector button Connects to 12VDC Power Supply Component & Analog/Digital Component & Analog/Digital Component & Analog/Digital Au
CONNECTING AND OPERATING THE 4X4 COMPONENT W/AUDIO MATRIX How to Connect the 4x4 Component w/Audio Matrix 1. Connect up to 4 component video/audio sources to the 4x4 Component w/ Audio Matrix inputs using the supplied 5 RCA analog stereo audio cable Optionally, connect digital coaxial audio to the 4x4 Component w/Audio Matrix using a user supplied digital coaxial cable. 2. Connect up to 4 component video displays to the 4x4 Component w/Audio Matrix outputs using user supplied component cables. 3.
RMT-16-IR REMOTE INSTALLATION 1. Remove battery cover from the back of the RMT-16-IR remote. 2. Verify that DIP switches 1 & 2 are in the down (OFF) position. 3. Insert the battery, hold the battery so that you can see the positive side facing up. The side that is not marked must be facing down. 4. Test the RMT-16-IR remote by pressing ONLY one button at a time. The indicator light on the remote will flash once each time you press a button.
IR CHANNEL CONFIGURATION How to Resolve IR Code Conflicts In the event that IR commands from other remote controls conflict with the supplied RMT-16IR remote control, changing the remote channel will alleviate this issue. The RMT-16IR remote control has a bank of DIP (Dual Inline Package) switches for configuring the remote channel that both units use to communicate.
RS-232 SERIAL CONTROL INTERFACE 54321 12345 9876 6789 Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interface Binary Table ASCII Corresponding RMT16-IR Button 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 Binary ASCII 0011 0001 0011 0010 0011 0011 0011 0100 0011 0101 0011 0110 0011 0111 0011 1000 9 a b c d e f g Corresponding RMT16-IR Button 9 10 11 12 13 14 15 16 Binary 0011 1001 0110 0001 0110 0010 0110 0011 0110 0100 0110 0101 0110 0110 0110 0111 Additional Features ASCII X or x
RACK MOUNT INSTALLATION Rack mount ears are provided for installation of this unit into a 1U rack mount space. 1. 2. 3. 4. Locate the side screws on the unit. Remove the front 2 screws that are located closest to the front of the unit. Using the removed screws, screw the rack mounting bracket into the unit. Repeat the procedure on the opposite side of the unit.
SPECIFICATIONS Video Amplifier Bandwidth ....................................................................... 350 MHz Input Video Signal .............................................................................. 1.2 Volts p-p Video Resolution .......................................................................................... 1080p Input Video Connectors ........................................................ RCA-style YPbPr x 4 Output Video Connectors .........................................
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
*ma-compaud-44424* Rev A3 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefen.com Pb This product uses UL listed power supplies. fax: 818-772-9120 support@gefen.