2x2 DPKVM Switch EXT-DPKVM-422 User Manual www.gefen.
ASKING FOR ASSISTANCE Technical Support: Telephone Fax (818) 772-9100 (800) 545-6900 (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday. Write To: Gefen LLC c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation without prior written notice. 2x2 DPKVM Switch is a trademark of Gefen, LLC © 2011 Gefen, LLC.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Panel Layout 5 Panel Descriptions 6 Connecting the 2x2 DPKVM Switch 7 Operating the 2x2 DPKVM Switch 8 RMT-2IR Remote Control Description 9 RMT-21IR Remote Installation 10 Infared (IR) Code Channel Configuration 11 RS-232 Serial Control Interface 12 Additional Switching Options 13 Specifications 14 Warranty
INTRODUCTION Congratulations on your purchase of the 2x2 DPKVM Switch. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 2X2 DPKVM SWITCH • The 2x2 DPKVM Switch supports Pass-through EDID. The Switch will use the EDID from the currently active input. • Dual Link resolutions up to 2560 x 1600 are supported.
FEATURES Features • Switches two high-definition displays between two DisplayPort-equipped computers with audio/video and USB peripherals • Switches up to 2560 x 1600 resolution • Supports RGB and YCbCr color spaces • Rack mountable • Save space on your desktop Supports Package Includes (1) 2x2 DPKVM Switch (4) 6 ft. DisplayPort Cables (2) 6 ft. USB 2.0 Cables (2) 6 ft. 3.
PANEL LAYOUT Front Panel 1 2 3 4 Back Panel 5 6 8 7 4 9 10 11 12 13 14
PANEL DESCRIPTIONS 1 I/R Receiver Receives I/R signal from the handheld Infrared remote control unit included with the 2x2 DVI KVM Switch. 2 LED Input Status Indicator 1 & 2 This currently selected source input will be indicated with an active LED. 3 Input Selector Button Pressing this button will cycle the input, 1 or 2, which will be selected for output. 4 Power Indicator This LED indicator will glow bright red when the power is turned on.
CONNECTING THE 2X2 DPKVM SWITCH Connecting Source Devices to the 2x2 DPKVM Switch 1. Connect up to two DisplayPort source devices to the DisplayPort inputs on the 2x2 DPKVM Switch using the included DisplayPort cables. 2. Connect up to two audio sources to the 3.5mm analog audio mini-jack inputs using the included audio cables. 3. Connect up to two USB source devices to the USB Type B inputs using the included USB Type A to B cables. 4.
OPERATING THE 2X2 DPKVM SWITCH How to Operate the 2x2 DPKVM Switch Switching can be accomplished via the front panel selector button, infrared (IR) remote control, or the RS-232 communications port. Additional switching options can be found on page 12 1 For information on switching via the front panel selector button, please see this page. 2 For information on switching via the infrared (IR) remote control, please see page 8.
RMT-2IR REMOTE CONTROL DESCRIPTION 1 2 1 Pressing this button will select Input 1 as the source. All devices connected to the input ports labeled 1 will be selected and output. 2 Pressing this button will select Input 2 as the source. All devices connected to the input ports labeled 2 will be selected and output.
RMT-2IR REMOTE INSTALLATION To use the RMT-2IR remote, remove the battery cover on the back of the remote to reveal the battery compartment. Insert the included battery into the open battery slot. The positive (+) side should be facing up. Ensure that both DIP (Dual Inline Package) switches are in the OFF position. Replace the battery cover. The remote ships with 2 batteries. One battery is needed for operation and the other battery is complimentary.
INFRARED (IR) CODE CHANNEL CONFIGURATION How to Resolve IR Code Conflicts In the event that IR commands from other remote controls conflict with the supplied RMT-2IR remote control, changing the remote channel will alleviate this issue. The RMT-2IR remote control and the 2x2 DPKVM Switch both have banks of DIP (Dual Inline Package) switches for configuring the remote channel that both units use to communicate. These settings must exactly match each other for proper operation.
RS-232 SERIAL CONTROL INTERFACE What features are available via the RS-232 serial communications port? The 2x2 DPKVM Switch can accept commands through the RS-232 serial communications port located on the rear panel. The current RS-232 control features are: • Switching of inputs. How do I use these features? These features were initially intended for utilization by custom installers in automated setups. However, these features can be tested by using any Windows PC with the Hyperterminal program.
ADDITIONAL SWITCHING OPTIONS The underside of the 2x2 DPKVM Switch features a DIP switch bank that is used to configure additional features. DIP switch 3 is used to control the function of Contact Closure-type remote controls on the rear panel.
SPECIFICATIONS Input Connector....................................................(4) DisplayPort (from computers) Output Connector...........................................................(2) DisplayPort (to display) Input Connector..........................................(2) USB 2.0 Type “B” (from computers) Output Connector..................................(2) USB 2.0 Type “A” (to keyboard/mouse) Input Connector...............................(2) 3.
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
Rev A2 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefen.com Pb This product uses UL or CE listed power supplies. fax: 818-772-9120 support@gefen.