DVI ELR Lite 3GSDI Audio Embedder Extender over one CAT-5 EXT-DVI-1CAT5-SR User Manual Release A1
DVI ELR Lite Extender over one CAT-5 Important Safety Instructions GENERAL SAFETY INFORMATION 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this product near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
DVI ELR Lite Extender over one CAT-5 Warranty Information Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
DVI ELR Lite Extender over one CAT-5 Contacting Gefen Technical Support Gefen, LLC c/o Customer Service 20600 Nordhoff St. Chatsworth, CA 91311 Telephone: (818) 772-9100 (800) 545-6900 Fax: (818) 772-9120 Email: support@gefen.com Visit us on the Web: www.gefen.com Technical Support Hours: 8:00 AM to 5:00 PM Monday - Friday, Pacific Time DVI ELR Lite Extender over one CAT-5 is a trademark of Gefen, LLC.
3GSDI DVI ELRAudio Lite Extender Embedder over one CAT-5 Operating Notes • CAT-5 cables should not exceed 200 feet (60 meters). CAT-6 cables should not exceed 230 feet (70 meters). • Shielded Twisted-Pair (STP) CAT-5 or CAT-6 cabling is recommended. However, Un-shielded Twisted-Pair (UTP) CAT-5 or CAT-6 cabling is acceptable. Shielded cable has an advantage by providing immunity to Electromagnetic Interference (EMI), cell phones and A/C motors.
DVI ELR Lite Extender over one CAT-5 Features and Packing List Features • Extends DVI up to 230 feet (70 meters) over one CAT-6A cable • Extends DVI up to 200 feet (60 meters) over one CAT-5e cable • Supports resolutions up to 1080p Full HD and 1920 x 1200 (WUXGA) • EDID management for rapid integration of source and display • Enable/Disable switches for HDCP and HPD pass-through • Locking power supplies • Surface-mountable 1080P ® Packing List The DVI ELR Lite Extender over one CAT-5 ships
3GSDI DVI ELRAudio Lite Extender Embedder over one CAT-5 Table of Contents 01 Getting Started Sender Unit Layout................................................................................................ 2 Front Panel..................................................................................................... 2 Back Panel..................................................................................................... 3 Bottom Panel..........................................................
DVI ELR Lite Extender over One CAT-5 01 Getting Started Sender Unit Layout................................................................................................ 2 Front Panel..................................................................................................... 2 Back Panel..................................................................................................... 3 Bottom Panel................................................................................................
Getting Started Sender Unit Layout Front Panel 2 3 4 1 ID Name Description 1 5V DC Connect the included 5V DC power supply to this power receptacle. 2 Link This LED indicator will glow bright green when power is applied and a CAT-5 cable is connected between the Sender and Receiver unit. If the source is not connected to the Sender unit, then this LED indicator will flash bright green. 3 DVI In Connect the DVI source to this port using the included DVI cable.
Getting Started Sender Unit Layout Back Panel 1 ID Name Description 1 Link Connect a CAT-5 cable from this jack to the Link jack on the Receiver unit.
Getting Started Sender Unit Layout Bottom Panel 1 ID Name Description 1 DIP switches Used for troubleshooting purposes only. See DIP Switch Configuration for more information.
Getting Started Receiver Unit Layout Front Panel 2 3 4 1 ID Name Description 1 5V DC Connect the included 5V DC power supply to this power receptacle. 2 Link This LED indicator will glow bright green when power is applied and a CAT-5 cable is connected between the Sender and Receiver unit. If the display (sink) is not connected to the Receiver unit, then this LED indicator will flash bright green. 3 DVI In Connect the DVI source to this port using the included DVI cable.
Getting Started Receiver Unit Layout Back Panel 1 ID Name Description 1 Link Connect a CAT-5 (or better) cable from this jack to the Link jack on the Sender unit.
Getting Started Installation Page Title Connecting the DVI ELR Lite Extender over one CAT-5 1. Use the included DVI cable to connect the DVI source to the DVI In port on the Sender unit. 2. Connect the Receiver unit to the display using another DVI cable. 3. Connect a CAT-5 (CAT-5e or better is recommended) cable, up to 200 feet (60 meters) from the Link jack on the Sender unit to the Link jack on the Receiver unit.
DVI ELR Lite Extender over One CAT-5 02 Appendix DIP Switch Configuration..................................................................................... 10 Specifications........................................................................................................
Appendix DIP Switch Configuration On the bottom panel of the DVI ELR Lite Extender over one CAT-5 are a bank of 4 DIP switches. Remove the piece of colored tape to reveal the DIP switch bank. These DIP switches provide control over EDID management, Hot-Plug Detect, and HDCP. DIP switch 4 is not used. These DIP switches are used for troubleshooting purposes, only.
Appendix Specifications Supported Formats Resolutions (max.
Stretch it, Switch it, Split it, Control it. Gefen’s got it. ® 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com Pb This product uses UL or CE listed power supplies.
