® EXT-HD-CP-FM10 User Manual www.gefen.
ASKING FOR ASSISTANCE Technical Support: Telephone Fax (818) 772-9100 (800) 545-6900 (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday through Friday, Pacific Time Write To: Gefen LLC c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation without prior written notice.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Cable Layout 5 Cable Descriptions 6 Connecting the HD Extender 1FO 6 Wiring Diagram 7 Operating the HD Extender 1FO 8 Specifications 9 Warranty
INTRODUCTION Congratulations on your purchase of the Gefen HD Extender 1FO. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
OPERATION NOTES PLEASE READ THESE NOTES BEFORE INSTALLING OR OPERATING THE HD EXTENDER 1FO • In most situations, the Sender pigtail module does not need to be externally powered unless the source does not supply enough power through the HDMI connector. If the Sender requires a separate power supply only use Gefen part no. EXT-PS52AIP-1.3. Using a different power supply other than the recommended type may cause fatal damage to the Sender pigtail module.
FEATURES Features • Extends HDMI up to 1000 feet (300 meters) using a single-strand 50/125μm multimode (OM2) SC-terminated fiber optic cable • Supports resolutions up 1080p Full HD • Supports HD lossless audio: LCPM 7.
CABLE LAYOUT 6 3 7 4 5 1 2 4
CABLE DESCRIPTIONS 1 Power Indicator (Sender module) This LED will glow bright green when the Hi-Def source is supplying sufficient power to the Sender module. If the LED flashes green, then the source is unable to power the Sender module. See page 7 for more information. 2 Fiber Optic Connector (Sender module) Connect an SC-terminated fiber optic cable from the Sender pigtail module to the SC fiber connector on the Receiver pigtail module.
CONNECTING THE HD EXTENDER 1FO How to Connect the HD Extender 1FO 1. Connect the Sender pigtail module to the Hi-Def source. 2. Connect the Receiver pigtail module to the HDTV display. 3. Connect a single strand of SC-terminated fiber optic cable between the fiber optic connectors on the Sender and Receiver pigtail modules. 4. Connect the included 5V DC power supply to power receptacle on the Receiver pigtail module. 5. Power-on the display and Hi-Def source.
OPERATING THE HD EXTENDER 1FO Power Indicators The power indicators on both the Sender and Receiver modules of the HD Extender 1FO provide information about the current power state. Normal operation If the power indicator on both the Sender and Receiver module glows bright green, then both the Sender and Receiver module have sufficient power.
SPECIFICATIONS Maximum Pixel Clock............................................................................... 225 MHz Video Input Connector (Sender)............................. (1) HDMI Type-A, 19-pin, male Video Output Connector (Receiver)....................... (1) HDMI Type-A, 19-pin, male Link Connector (Sender/Receiver).......................... (1) Type SC fiber (50 /125μm) Power Supply (Receiver).......................................................................
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
Rev A1 Pb This product uses UL or CE listed power supplies.