® 1:2 Splitter For HDMI 1.3 EXT-HDMI1.3-142 User’s Manual www.gefen.
ASKING FOR ASSISTANCE Technical Support: Telephone Fax (818) 772-9100 (800) 545-6900 (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday PST Write To: Gefen LLC c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen LLC reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice. 1:2 Splitter For HDMI 1.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Panel Descriptions 6 Connecting And Operating The 1:2 Splitter For HDMI 7 Specifications 8 Warranty
INTRODUCTION Congratulations on your purchase of the 1:2 Splitter For HDMI. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 1:2 SPLITTER FOR HDMI 1.3 • By default, display information from the display connected to HDMI output port 1 is sent back to the source. Therefore, the other display connected to the 1:2 Splitter for HDMI 1.3 must be capable of accepting the timings and resolutions of the display that is connected to HDMI output port 1. It is recommended that the display with the lowest native resolution be connected to HDMI output port 1.
FEATURES Features • Connects up to two HDMI / DVI displays from one HDMI source • Optionally add more displays by connecting splitters • Easily attains resolutions up to 1080p, 2k, and 1920 x 1200 • HDMI and HDCP compliant HDMI 1.
PANEL DESCRIPTIONS Front Panel 1 2 3 4 Back Panel 5 6 7 8 9 10 1 Power LED This LED will activate once a valid power source is applied. 2 Internal EDID LED This LED will activate only when the pre-programmed internal EDID is being used. Please see page 6 for more details on the internal EDID. 3 External EDID LED (default EDID routing) This LED will activate only when the external EDID is being used. Please see page 6 for more details on the external EDID.
PANEL DESCRIPTIONS 7 HDMI Input This is the input for the HDMI source device. When a valid source is detected by the splitter, the Link LED will activate. 8 HDMI Out 1 This is the first HDMI output port. Connect a valid HDMI display to this port. When the External EDID mode is active, the EDID form the display connected to this port will be used to send to the source. 9 HDMI Out 2 This is the second HDMI output port. Connect a valid HDMI display to this port.
CONNECTING AND OPERATING THE 1:2 SPLITTER FOR HDMI How to Connect the 1:2 Splitter For HDMI 1.3 1. Connect the supplied cable from the HDMI source into the 1:2 Splitter for HDMI 1.3 input. 2. Connect the cables from your displays (monitor or projector) into the HDMI outs of the 1:2 Splitter for HDMI 1.3. Up to 2 displays are supported. 3. Plug the 5V DC power supply into the 1:2 Splitter for HDMI 1.3.
SPECIFICATIONS Video Amplifier Bandwidth ............................................................... 225 MHz Input Video Signal ...................................................................... 1.2 Volts p-p Input DDC Signal ................................................................ 5 Volts p-p (TTL) Single Link Range ........................................................... 1080p/1920 x 1200 HDMI Connector .........................................................
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
*ma-HDMI1.3-142* Rev A1 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefen.com Pb fax: 818-772-9120 support@gefen.
