® 1:2 Splitter for HDMI® 1.3 with Digital Audio EXT-HDMI1.3-142D User Manual www.gefen.
ASKING FOR ASSISTANCE Technical Support: Telephone Fax (818) 772-9100 (800) 545-6900 (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday PST Write To: Gefen, LLC. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen, LLC reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice. 1:2 Splitter For HDMI 1.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Panel Descriptions 5 Panel Descriptions 6 Connecting and Operating The 1:2 Splitter For HDMI 1.
INTRODUCTION Congratulations on your purchase of the 1:2 Splitter For HDMI 1.3. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 1:2 SPLITTER FOR HDMI 1.3 WITH DIGITAL AUDIO • By default, display information from the display connected to HDMI output port 1 is sent back to the source. Therefore, the other display connected to the 1:2 Splitter for HDMI 1.3 with Digital Audio must be capable of accepting the timings, resolutions and audio formats of the display that is connected to HDMI output port 1.
FEATURES HDMI 1.3 Features • 225 MHz (up to 12 bit YUV 444 supported @ 1080p) • Deep Color • Dolby TrueHD and DTS-HD Master Audio • Lip-Sync • CEC Pass-Through Features • Simultaneously displays a single Hi-Def source on up to two (2) HDTV displays without signal loss • Maintains sharp HDTV resolutions up to 1080p Full HD and 2K • 3DTV Pass-Through • Color Space Conversion • EDID Management for rapid integration of sources and display devices.
PANEL LAYOUT Front Panel 1 2 3 4 Back Panel 5 6 7 8 9 4 10 11
PANEL DESCRIPTIONS 1 Power LED This LED will activate once a valid power source is applied. 2 Internal EDID LED This LED will activate only when the pre-programmed internal EDID is being used. Please see page 7 for more details on the internal EDID. 3 External EDID LED (default EDID routing) This LED will activate only when the external EDID is being used. Please see page 7 for more details on the external EDID. 4 Link LED This LED activates when a valid link between source and splitter is detected.
CONNECTING AND OPERATING THE 1:2 SPLITTER FOR HDMI 1.3 WITH DIGITAL AUDIO How to Connect the 1:2 Splitter for HDMI 1.3 with Digital Audio 1. Connect the supplied cable from the HDMI source into the Splitter’s input. 2. Connect the cables from your displays (monitor or projector) into the HDMI outs of the 1:2 Splitter for HDMI 1.3 with Digital Audio. Up to 2 displays are supported. 3. If using the TOSLINK optical audio output, connect a TOSLINK optical audio cable between the 1:2 Splitter for HDMI 1.
EDID MANAGEMENT EDID Mode Selection 1. EXTERNAL MODE: See page 8 for details on using the External EDID. 2. INTERNAL MODE: To use this mode, press the EDID button on the rear panel until the frontpanel LED marked “Int” turns bright green. This mode will use a preset EDID, from the factory, that is stored in the Gefen 1:2 Splitter for HDMI 1.3 with Digital Audio. This pre-programmed standard EDID data structure is compatible with most A/V display devices.
EDID MANAGEMENT External EDID Management The 1:2 Splitter for HDMI 1.3 with Digital Audio features EDID Management. Before the source can send video or audio signals, the source device reads the EDID (Extended Display Identification Data) from the output devices connected to the Splitter. The EDID contains information about what type of A/V data that the source can send to each output device. The 1:2 Splitter for HDMI 1.3 with Digital Audio distributes a single source to multiple output devices.
SPECIFICATIONS Video Amplifier Bandwidth ............................................................... 225 MHz Input Video Signal ...................................................................... 1.2 Volts p-p Input DDC Signal ................................................................ 5 Volts p-p (TTL) Single Link Range ........................................................... 1080p/1920 x 1200 HDMI Connector ........................................................
10
Rev B2 2.1M 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefen.com fax: 818-772-9120 support@gefen.
