*Preferred VGA & Audio to HDMI Scaler/Converter EXT-VGAA-HD-SC User Manual Release A1
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this product near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install or place this product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Warranty Information Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
Contacting Gefen Technical Support Technical Support (818) 772-9100 (800) 545-6900 8:00 AM to 5:00 PM Monday - Friday, Pacific Time Fax (818) 772-9120 Email support@gefen.com Web http://www.gefen.com Mailing Address Gefen, LLC c/o Customer Service 20600 Nordhoff St. Chatsworth, CA 91311 Product Registration Register your product here: http://www.gefen.com/kvm/Registry/Registration.
Operating Notes • Audio from the 2-channel analog input will be automatically embedded into the HDMI output signal. • By default, the current input and output resolution will be displayed whenever the VGA & Audio to HDMI Scaler/Converter is disconnected from the source or display or if a change in the video output settings are made. This feature can be disabled through the Display Notify option See Display Notify (page 37) and the #set_display_notify command for more information.
Features and Packing List Features • Converts and scales VGA and L/R analog audio to HDMI • Input resolutions up to 1920 x 1200 (WUXGA) • Output resolutions up to 1080p60 and 1920 x 1200 (WUXGA) • On-screen display (OSD) menu allows easy set-up and control • Aspect Ratio Control: Full Screen, Panoramic, Letter/Pillar, Extract/Crop • Test Pattern Generator for quick system configuration • Embeds 2-channel analog stereo audio in HDMI signal • Gefen Syner-G™ simplifies in-field firmware updates
Table of Contents 1 Getting Started Introduction............................................................................................................ 2 Installation.............................................................................................................. 4 Connection Instructions.................................................................................. 4 Sample Wiring Diagram.................................................................................
Table of Contents 3 Advanced Operation USB Interface....................................................................................................... 48 Installing the Virtual COM Port..................................................................... 48 Commands........................................................................................................... 50 Using Preset Values.....................................................................................
VGA & Audio to HDMI Scaler/Converter 1 Getting Started Introduction............................................................................................................ 2 Installation.............................................................................................................. 4 Connection Instructions.................................................................................. 4 Sample Wiring Diagram...............................................................................
Introduction Getting Started Page Title 1 2 EXT-VGAA-HD-SC EXT-VGAA-HD-SC HDMI Out Up Dn Menu HDMI Out Up Dn Menu EXT-VGAA-HD-SC ® HDMI Out Up Dn Menu ® ® VGA & Audio to HDMI Scaler/Converter VGA & Audio to HDMI Scaler/Converter VGA In VGA & Audio to HDMI L/R In USB 12V DC Pwr Scaler/Converter VGA In 3 L/R In 4 USB 5 12V DC 6 Pwr VGA In L/R In USB 12V DC Pwr page | 2 7
Getting Started Introduction Page Title ID Name Description 1 HDMI Out Use an HDMI cable to connect a Hi-Def display to this HDMI port. 2 Up, Dn, Menu These push-buttons are used to change settings within the on-screen menu system. See Menu System (page 8) for more information. 3 VGA In Connect the included VGA cable from source device (e.g. computer) to this port. 4 L/R In Connect the included 3.5mm mini-stereo cable from this port to the audio output port on the audio source device.
Getting Started Installation Connection Instructions ►► Video 1. Connect the included VGA cable from the video source (e.g. computer) to the VGA In port on the VGA & Audio to HDMI Scaler/Converter. 2. Connect an HDMI cable from the HDMI Out port to an HD display. ►► Audio 3. Connect the included 3.5mm mini-stereo cable from the audio source to the L/R In port on the VGA & Audio to HDMI Scaler/Converter. ►► Power 4.
VGA & Audio to HDMI Scaler/Converter 2 Basic Operation Menu System......................................................................................................... 8 Displaying the Menu System.......................................................................... 8 Moving around within the Menu System........................................................ 9 Output Resolution........................................................................................ 12 Output Color..................
Basic Operation Menu System Displaying the Menu System The VGA & Audio to HDMI Scaler/Converter uses a built-in menu system to manage and control all video features. 1. To display the menu system, press the Menu button on the front panel. Menu controls EXT-VGAA-HD-SC HDMI Out 2. Up Dn Menu The menu system will be displayed in the upper-left corner of the screen, as shown below: ® Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit Output Resolu.
Basic Operation Menu System Moving around within the Menu System 1. There are six menu items within the main menu: Output Setup, Picture, Adjustment, System, Test Patterns, and Exit. 2. The currently selected item within the main menu will always be highlighted in yellow. 3. Each item within the main menu, with the exception of Exit, contains a submenu. The submenu, for each item in the main menu, is displayed automatically. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.
Basic Operation Menu System 5. To access the submenu for the highlighted item within the main menu, press the Menu button a second time. When a submenu is activated, a green bar is used to indicate the current selection. By default, the top submenu item will always be highlighted once a submenu is activated. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit 6. OSD Timeout Display Notify Input Res.
Basic Operation Menu System 9. To exit the submenu and return to the main menu, use the Up or Dn button to highlight the <- Back option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit OSD Timeout Display Notify Input Res.Info F/W Version Factory Reset <- Back 10. Press the Menu button to return to the main menu. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit OSD Timeout Display Notify Input Res.
Menu System Basic Operation Output Resolution Warning Before changing this setting, make sure that the connected display can support the selected output resolution. If an unsupported resolution is selected, the unit will need to be reset using the DIP switch on the bottom of the unit. See DIP Switch Configuration (page 44) for more information. 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Press the Menu button to access the Output Setup submenu.
Basic Operation Menu System Information The input/output resolution information dialog will only be displayed if Display Notify is set to On. See Display Notify (page 37) for more information. 8. After a few seconds, the input and output resolution information dialog will disappear. 9. The Output Resolu. dialog is still displayed: Output Resolu. a[ 640x480p60 ]a 10. Press the Menu button to return to the Output Setup submenu: Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.
Basic Operation Menu System Output Color 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Press the Menu button to access the Output Setup submenu. The Output Resolu. option will be highlighted. 3. Use the Up or Dn button to highlight the Output Color option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit Output Resolu. Output Color Output Mode <- Back 4.
Basic Operation Menu System 9. Press the Menu button to return to the Output Setup submenu. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit Output Resolu. Output Color Output Mode <- Back 10. Use the Up or Dn button to select the <- Back option. 11. Press the Menu button. 12. Use the Up or Dn button to select the Exit option 13. Press the Menu button to exit the main menu.
Basic Operation Menu System Output Mode 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Press the Menu button to access the Output Setup submenu. The Output Resolu. option will be highlighted. 3. Use the Up or Dn button to highlight the Output Mode option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit Output Resolu. Output Color Output Mode <- Back 4.
Basic Operation Menu System 9. Press the Menu button to return to the Output Setup submenu. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit Output Resolu. Output Color Output Mode <- Back 10. Use the Up or Dn button to select the <- Back option. 11. Press the Menu button. 12. Use the Up or Dn button to select the Exit option 13. Press the Menu button to exit the main menu.
Basic Operation Menu System Contrast 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Picture option. 3. Press the Menu button to access the Picture submenu. The Contrast option will be highlighted. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit Contrast Brightness Saturation Hue Color Range Color Temp. Color Balance Edge Enhance Sharpness <- Back 4.
Basic Operation Menu System Brightness 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Picture option. 3. Press the Menu button to access the Picture submenu. The Contrast option will be highlighted. 4. Use the Up or Dn button to highlight the Brightness option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System Saturation 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Picture option. 3. Press the Menu button to access the Picture submenu. The Contrast option will be highlighted. 4. Use the Up or Dn button to highlight the Saturation option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System Hue 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Picture option. 3. Press the Menu button to access the Picture submenu. The Contrast option will be highlighted. 4. Use the Up or Dn button to highlight the Hue option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit Contrast Brightness Saturation Hue Color Range Color Temp.
Basic Operation Menu System Color Range 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Picture option. 3. Press the Menu button to access the Picture submenu. The Contrast option will be highlighted. 4. Use the Up or Dn button to highlight the Color Range option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System Color Temperature 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Picture option. 3. Press the Menu button to access the Picture submenu. The Contrast option will be highlighted. 4. Use the Up or Dn button to highlight the Color Temp. option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System Color Balance 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Picture option. 3. Press the Menu button to access the Picture submenu. The Contrast option will be highlighted. 4. Use the Up or Dn button to highlight the Color Balance option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System Edge Enhance 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Picture option. 3. Press the Menu button to access the Picture submenu. The Contrast option will be highlighted. 4. Use the Up or Dn button to highlight the Edge Enhance option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System Sharpness 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Picture option. 3. Press the Menu button to access the Picture submenu. The Contrast option will be highlighted. 4. Use the Up or Dn button to highlight the Sharpness option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System Underscan/Overscan 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Adjustment option. 3. Press the Menu button to access the Adjustment submenu. The Under/Over Scan option will be highlighted. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit Under/Over Scan Aspect Ratio H-Mirror V-Mirror H-Shift V-Shift Phase <- Back 4.
Basic Operation Menu System Aspect Ratio 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Adjustment option. 3. Press the Menu button to access the Adjustment submenu. The Under/Over Scan option will be highlighted. 4. Use the Up or Dn button to highlight the Aspect Ratio option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System Horizontal Mirror 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Adjustment option. 3. Press the Menu button to access the Adjustment submenu. The Under/Over Scan option will be highlighted. 4. Use the Up or Dn button to highlight the H-Mirror option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System 8. Press the Menu button to confirm the change and return to the Adjustment submenu. 9. Use the Up or Dn button to select the <- Back option. 10. Press the Menu button. 11. Use the Up or Dn button to select the Exit option 12. Press the Menu button to exit the main menu.
Basic Operation Menu System Vertical Mirror 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Adjustment option. 3. Press the Menu button to access the Adjustment submenu. The Under/Over Scan option will be highlighted. 4. Use the Up or Dn button to highlight the V-Mirror option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System 8. Press the Menu button to confirm the change and return to the Adjustment submenu. 9. Use the Up or Dn button to select the <- Back option. 10. Press the Menu button. 11. Use the Up or Dn button to select the Exit option 12. Press the Menu button to exit the main menu.
Basic Operation Menu System Horizontal Shift 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Adjustment option. 3. Press the Menu button to access the Adjustment submenu. The Under/Over Scan option will be highlighted. 4. Use the Up or Dn button to highlight the H-Shift option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System Vertical Shift 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Adjustment option. 3. Press the Menu button to access the Adjustment submenu. The Under/Over Scan option will be highlighted. 4. Use the Up or Dn button to highlight the V-Shift option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System Phase 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Adjustment option. 3. Press the Menu button to access the Adjustment submenu. The Under/Over Scan option will be highlighted. 4. Use the Up or Dn button to highlight the Phase option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System OSD Timeout 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the System option. 3. Press the Menu button to access the System submenu. The OSD Timeout option will be highlighted. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit OSD Timeout Display Notify Input Res.Info F/W Version Factory Reset <- Back 4.
Basic Operation Menu System Display Notify 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the System option. 3. Press the Menu button to access the System submenu. The OSD Timeout option will be highlighted. 4. Use the Up or Dn button to highlight the Display Notify option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit OSD Timeout Display Notify Input Res.
Basic Operation Menu System 8. Press the Menu button to confirm the change and return to the System submenu. 9. Use the Up or Dn button to select the <- Back option. 10. Press the Menu button. 11. Use the Up or Dn button to select the Exit option 12. Press the Menu button to exit the main menu.
Basic Operation Menu System Input Resolution Information 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the System option. 3. Press the Menu button to access the System submenu. The OSD Timeout option will be highlighted. 4. Use the Up or Dn button to highlight the Input Res. Info option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.
Basic Operation Menu System F/W Version 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the System option. 3. Press the Menu button to access the System submenu. The OSD Timeout option will be highlighted. 4. Use the Up or Dn button to highlight the F/W Version option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit OSD Timeout Display Notify Input Res.
Basic Operation Menu System Factory Reset 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the System option. 3. Press the Menu button to access the System submenu. The OSD Timeout option will be highlighted. 4. Use the Up or Dn button to highlight the Factory Reset option. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit OSD Timeout Display Notify Input Res.
Basic Operation Menu System Test Patterns 1. Press the Menu button on the front panel. The Output Setup option will be highlighted. 2. Use the Up or Dn button to highlight the Test Patterns option. 3. Press the Menu button to access the Test Patterns submenu. The White option will be highlighted. Gefen Converter ---------------1.Output Setup 2.Picture 3.Adjustment 4.System 5.Test Patterns 6.Exit White Cross Hatch Color Gray Window Off <- Back 4.
Basic Operation Menu System Gray Window 6. Press the Menu button to return to the Test Patterns submenu and select a different pattern. 7. To disable the pattern and view the source image, select Off from the Test Patterns submenu.
EXT-VGAA-HD-SC HDMI Out Up Dn Menu 1 ON On the bottom panel of the VGA & Audio to HDMI Scaler/Converter is a single DIP switch. Remove the piece of colored tape to reveal the DIP switch bank. 1 O N Basic Operation DIP Switch Configuration By default, the DIP switch is in the OFF (1) position. The DIP switch should remain in this position during normal operation.
VGA & Audio to HDMI Scaler/Converter 3 Advanced Operation USB Interface....................................................................................................... 48 Installing the Virtual COM Port..................................................................... 48 Commands........................................................................................................... 50 Using Preset Values.....................................................................................
Advanced Operation USB Interface Installing the Virtual COM Port In order to control the VGA & Audio to HDMI Scaler/Converter using the following commands, a virtual COM port must be installed on the computer that is connected to the VGA & Audio to HDMI Scaler/Converter. 1. Install the Gefen Syner-G Software Suite. This software is available under the Support > Downloads section of the Gefen website. 2.
Advanced Operation USB Interface 6. The Computer Management window will open. 7. In the left window pane, under System Tools, click Device Manager. 8. In the right window pane, locate Ports (COM & LPT). The device EXT-VGAA-HD-SC will be displayed along with the COM port. Use this COM port when configuring the terminal program (e.g. Hyperterminal).
Advanced Operation Commands Command Description #factory_reset Resets the unit to factory-default settings #fw_upgrade Enables the firmware upgrade mode #get_aspect_ratio Displays the current aspect ratio setting #get_brightness Displays the current brightness setting #get_color_balance Displays the value of the specified color channel #get_color_range Displays the current color range setting #get_color_temp Displays the current color temperature setting #get_contrast Displays the current
Advanced Operation Commands Command Description #set_color_balance Sets the color balance #set_color_range Set the output color range #set_color_temp Sets the color temperature #set_contrast Sets the picture contrast #set_display_notify Enables / disables display notifications #set_edge_enhance Sets the edge enhancement #set_horizontal_mirror Sets horizontal mirror #set_horizontal_shift Sets horizontal shift #set_horz_active Sets the horizontal active #set_horz_back_porch Sets the hor
Advanced Operation Commands Using Preset Values When a command is entered, the VGA & Audio to HDMI Scaler/Converter will confirm the entry by returning the function of the command and any parameters. There are several commands which use a preset value as one of the parameters. When specifying a preset value as a parameter, the returned preset value will always be one greater than the value that was specified.
Advanced Operation Commands #factory_reset Resets the unit to factory-default settings.
Advanced Operation Commands #fw_upgrade Enables the firmware upgrade mode. We recommend that the Gefen Syner-G Software Suite be used to upgrade the firmware. Syntax #fw_upgrade Parameters None Example #fw_upgrade Waiting for firmware file to be received...
Advanced Operation Commands #get_aspect_ratio Displays the current aspect ratio setting.
Advanced Operation Commands #get_brightness Displays the current brightness value.
Advanced Operation Commands #get_color_balance Displays the current color balance for the specified color channel. Syntax #get_color_balance param1 Parameters param1 Color channel param1 Description 0 Red channel 1 Green channel 2 Blue channel Example #get_color_balance 1 PICTURE COLOR BALANCE Green Channel IS 50 Related Commands #set_color_balance page | 57 [0 ...
Advanced Operation Commands #get_color_range Displays the current color range setting.
Advanced Operation Commands #get_color_temp Displays the current color temperature setting.
Advanced Operation Commands #get_contrast Displays the current contrast setting.
Advanced Operation Commands #get_display_notify Displays the current display-notify setting. Refer to the #set_display_notify command for more information about Display Notification.
Advanced Operation Commands #get_edge_enhance Displays the current edge-enhance setting.
Advanced Operation Commands #get_firmware_version Displays the current firmware version. Syntax #get_firmware_version Parameters None Example #get_firmware_version FIRMWARE VERSION IS V1.
Advanced Operation Commands #get_horizontal_mirror Displays the horizontal mirror setting.
Advanced Operation Commands #get_horizontal_shift Displays the current horizontal shift setting.
Advanced Operation Commands #get_hue Displays the current hue setting.
Advanced Operation Commands #get_input_resolution Displays the current input resolution.
Advanced Operation Commands #get_osd_timeout Displays the current OSD timeout value (in seconds).
Advanced Operation Commands #get_output_color Displays the current output color space.
Advanced Operation Commands #get_output_mode Displays the current output mode.
Advanced Operation Commands #get_output_res Displays the current output resolution.
Advanced Operation Commands #get_phase Displays the current phase setting.
Advanced Operation Commands #get_picture_settings Displays the current picture settings. This command provides the same information as consecutively executing the following commands: #get_contrast, #get_brightness, #get_saturation, #get_hue, get_color_range, #get_color_temp, #get_color_balance, #get_edge_enhance, and #get_sharpness.
Advanced Operation Commands #get_saturation Displays the current saturation value.
Advanced Operation Commands #get_sharpness Displays the current sharpness value.
Advanced Operation Commands #get_test_patterns Displays the currently active test pattern.
Advanced Operation Commands #get_timing_preset Displays the values for the specified timing preset. Syntax #get_timing_preset Parameters param1 Preset [0 ... 5] Example #get_timing_preset 1 Preset 2 Hor Scan = 45.0 Hor Active = 1280 Hor Ft Porch = 110 Hor Sync W = 40 Hor Bk Porch = 220 Hor Total = 1650 Hor Polarity = + Pixel Clk = 74.25 Ver Ver Ver Ver Ver Ver Ver Refresh = 60.
Advanced Operation Commands #get_uo_scan Displays the current underscan or overscan value.
Advanced Operation Commands #get_vertical_mirror Displays the current vertical mirror value.
Advanced Operation Commands #get_vertical_shift Displays the current vertical shift value.
Advanced Operation Commands #get_video_output Displays the current video output settings. This command produces the same output as consecutively executing the #get_output_res, #get_output_color, and #get_output_mode commands.
Advanced Operation Commands #get_video_settings Displays the current video settings. This command provides the same information as consecutively executing the #get_uo_scan, #get_aspect_ratio, #get_horizontal_mirror, #get_vertical_mirror, #get_horiziontal_shift, #get_vertical_shift, and #get_phase commands.
Advanced Operation Commands #help Displays help on a specific command. If no command is specified (param1), then a list of all available commands will be displayed. Syntax #help [param1] Parameters param1 Command (optional) Examples #help #FACTORY_RESET #FW_UPGRADE #GET_ASPECT_RATIO #GET_BRIGHTNESS #SET_COLOR_BALANCE #GET_COLOR_RANGE #GET_COLOR_TEMP #GET_CONTRAST #GET_DISPLAY_NOTIFY #GET_EDGE_ENHANCE ... ...
Advanced Operation Commands #reboot Reboots the unit.
Advanced Operation Commands #set_aspect_ratio Sets the aspect ratio of the output video signal. The default setting is 0. Syntax #set_aspect_ratio param1 Parameters param1 Aspect ratio param1 Description 0 16:9 1 4:3 2 Stretch 3 Source Example #set_aspect_ratio 1 ASPECT RATIO SET TO 4:3 Related Commands #get_aspect_ratio page | 85 [0 ...
Advanced Operation Commands #set_brightness Sets the brightness of the output video signal. The default setting is 50. Syntax #set_brightness param1 Parameters param1 Brightness [0 ...
Advanced Operation Commands #set_color_balance Sets the color balance of the output video signal. Syntax #set_color_balance param1 param2 Parameters param1 param2 Color channel param1 Description 0 Red 1 Green 2 Blue [0 ... 2] Intensity [0 ...
Advanced Operation Commands #set_color_range Sets the color range of the output video signal. Syntax #set_color_range param1 Parameters param1 Color range param1 Description 0 Full (0 - 255) 1 Limited (16 - 235) Example #set_color_range 1 PICTURE COLOR RANGE SET TO Limited Related Commands #get_color_range #set_color_balance #set_color_temp page | 88 [0 ...
Advanced Operation Commands #set_color_temp Sets the color temperature of the output video signal. Syntax #set_color_temp param1 Parameters param1 Color temperature param1 Description 0 Warm 1 Neutral 2 Cool Example #set_color_temp 2 PICTURE COLOR TEMPERATURE SET TO Cool Related Commands #get_color_temp #set_color_balance #set_color_range page | 89 [0 ...
Advanced Operation Commands #set_contrast Sets the contrast of the output video signal. Syntax #set_contrast param1 Parameters param1 Contrast [0 ...
Advanced Operation Commands #set_display_notify Enables / disables the input/output resolution information dialog. When set to On, the input/ output resolution information dialog will be displayed, momentarily, whenever the source is disconnected / reconnected to the VGA & Audio to HDMI Scaler/Converter or if a change to the output is made. When set to Off, the information dialog will not be displayed.
Advanced Operation Commands #set_edge_enhance Sets the picture edge enhancement (sharpness) threshold. The Mid and Max settings are sharpness presets. To set the sharpness to a specific setting, set param1 = 3, then use the #set_sharpness command to set the sharpness value.
Advanced Operation Commands #set_horizontal_mirror Enables or disables horizontal mirroring. When set to on, the output image is flipped horizontally. Syntax #set_horizontal_mirror param1 Parameters param1 State param1 Description 0 Off 1 On Example #set_horizontal_mirror 1 HORIZONTAL MIRROR SET TO On Related Commands #get_horizontal_mirror #get_video_settings #set_vertical_mirror page | 93 [0 ...
Advanced Operation Commands #set_horizontal_shift Adjust the horizontal position of the output image. Syntax #set_horizontal_shift param1 Parameters param1 Horizontal shift Example #set_horizontal_shift -20 HORIZONTAL SHIFT IS SET TO -20 Related Commands #get_horizontal_shift #get_video_settings #set_vertical_shift page | 94 [-100 ...
Advanced Operation Commands #set_horz_active Sets the number of active horizontal pixels and saves it to the specified preset. Syntax #set_horz_active param1 param2 Parameters param1 param2 Pixels [0 ... 9999] Preset [0 ...
Advanced Operation Commands #set_horz_back_porch Sets the horizontal back porch and saves it to the specified preset. Syntax #set_horz_back_porch param1 param2 Parameters param1 param2 Pixels [0 ... 9999] Preset [0 ...
Advanced Operation Commands #set_horz_front_porch Sets the horizontal front porch and saves it to the specified preset. Syntax #set_horz_front_porch param1 param2 Parameters param1 param2 Pixels [0 ... 9999] Preset [0 ...
Advanced Operation Commands #set_horz_scan_rate Sets the horizontal scan rate and saves it to the specified preset. param1 is a floating-point value and can be specified up to three decimal places. Syntax #set_horz_scan_rate param1 param2 Parameters param1 param2 Scan rate (kHz) [0.000 ... 999.000] Preset [0 ...
Advanced Operation Commands #set_horz_sync_polarity Sets the horizontal sync polarity and saves it to the specified preset. Syntax #set_horiz_sync_polarity param1 param2 Parameters param1 param2 State param1 Description 0 Negative 1 Positive [0 ... 1] Preset [0 ...
Advanced Operation Commands #set_horz_sync_width Sets the horizontal sync width in pixels and saves it to the specified preset. Syntax #set_horz_sync_width param1 param2 Parameters param1 param2 Width (pixels) [0 ... 9999] Preset [0 ...
Advanced Operation Commands #set_horz_total Sets the total number of horizontal pixels and saves it to the specified preset. Syntax #set_horz_total param1 param2 Parameters param1 param2 Total (pixels) [0 ... 9999] Preset [0 ...
Advanced Operation Commands #set_hue Sets the picture hue of the output video signal. Syntax #set_hue param1 Parameters param1 Hue [0 ...
Advanced Operation Commands #set_osd_timeout Sets the OSD (On-Screen Display) time-out delay in seconds. If param1 = 0, then the OSD timeout will be set to “off”. The OSD will be displayed until it is exited, manually. See Moving around within the Menu System (page 9) for more information on how to manually exit the menu system.
Advanced Operation Commands #set_output_color Sets the output color space. Syntax #set_output_color param1 Parameters param1 Color space param1 Description 0 RGB 4:4:4 1 YCbCr 4:4:4 2 YCbCr 4:2:2 Example #set_output_color 1 OUTPUT COLOR SPACE SET TO YCbCr 4:4:4 Related Commands #get_output_color #set_color_balance #set_color_range #set_color_temp page | 104 [0 ...
Advanced Operation Commands #set_output_mode Sets the output mode. Syntax #set_output_mode param1 Parameters param1 Mode [0 ...
Advanced Operation Commands #set_output_res Sets the output resolution. Resolutions that use reduced-blanking are indicated with “(RB)”. Note the following frequency information: 23 = 23.98, 29 = 29.97, and 59 = 59.94.
Advanced Operation Commands param1 Description 22 SD (480i) / 60 Hz 23 SD (576i) / 50 Hz 24 SD (480p) / 60 Hz 25 SD (576p) / 50 Hz 26 HD (720p) / 60 Hz 27 HD (720p) / 59 Hz 28 HD (720p) / 50 Hz 29 HD (720p) / 30 Hz 30 HD (720p) / 29 Hz 31 HD (720p) / 25 Hz 32 HD (1080i) / 60 Hz 33 HD (1080i) / 59 Hz 34 HD (1080i) / 50 Hz 35 HD (1080p) / 60 Hz 36 HD (1080p) / 59 Hz 37 HD (1080p) / 50 Hz 38 HD (1080p) / 30 Hz 39 HD (1080p) / 29 Hz 40 HD (1080p) / 25 Hz 41 HD (1080p)
Advanced Operation Commands #set_phase Sets the phase adjustment. The default setting is “Auto”. Syntax #set_phase param1 Parameters param1 Phase Example #set_phase 26 PHASE SET TO 26 Related Commands #get_phase page | 108 [Auto, 1 ...
Advanced Operation Commands #set_pixel_clock Sets the pixel clock and saves it to the specified preset. param1 is a floating-point value and can be specified up to three decimal places. Syntax #set_pixel_clock param1 param2 Parameters param1 param2 Pixel clock [0.000 ... 999.000] Preset [0 ... 5] Example #set_pixel_clock 74.25 1 PIXEL CLOCK 74.
Advanced Operation Commands #set_saturation Sets the picture saturation. Syntax #set_saturation param1 Parameters param1 Saturation Example #set_saturation 65 PICTURE SATURATION SET TO 65 Related Commands #set_brightness #set_contrast #set_hue page | 110 [0 ...
Advanced Operation Commands #set_sharpness Sets the picture saturation. In order to set the sharpness value, the Edge Enhance setting must be set to User. Refer to the #set_edge_enhance command for details. Syntax #set_sharpness param1 Parameters param1 Sharpness Example #set_sharpness 68 PICTURE SHARPNESS SET TO 68 Related Commands #set_edge_enhance page | 111 [0 ...
Advanced Operation Commands #set_test_patterns Enables / disables or sets the test pattern. Syntax #set_test_patterns param1 Parameters param1 Pattern [0 ...
Advanced Operation Commands #set_uo_scan Adjusts the underscan / overscan of the output image. The default value is 0. Negative values produce an “underscanned” image. Positive values produce an “overscanned” image. Syntax #set_uo_scan param1 Parameters param1 Amount (%) Example #set_uo_scan 10 UNDER/OVER SCAN SET TO 10% Related Commands #get_uo_scan page | 113 [-50 ...
Advanced Operation Commands #set_vert_active Sets the vertical active pixels and saves it to the specified preset. Syntax #set_vert_active param1 param2 Parameters param1 param2 Pixels [0 ... 9999] Preset [0 ...
Advanced Operation Commands #set_vert_back_porch Sets the vertical back porch and saves it to the specified preset. Syntax #set_vert_back_porch param1 param2 Parameters param1 param2 Pixels [0 ... 9999] Preset [0 ...
Advanced Operation Commands #set_vert_front_porch Sets the vertical front porch and saves it to the specified preset. Syntax #set_vert_front_porch param1 param2 Parameters param1 param2 Pixels [0 ... 9999] Preset [0 ...
Advanced Operation Commands #set_vert_refresh_rate Sets the vertical refresh rate and saves it to the specified preset. param1 is a floating-point value and can be specified up to three decimal places. Syntax #set_vert_refresh_rate param1 param2 Parameters param1 param2 Refresh rate [0.000 ... 9999.000] Preset [0 ...
Advanced Operation Commands #set_vert_sync_polarity Sets the vertical sync polarity and saves it to the specified preset. Syntax #set_vert_sync_polarity param1 param2 Parameters param1 param2 Polarity [0 ... 1] param1 Description 0 Negative 1 Positive Preset [0 ...
Advanced Operation Commands #set_vert_sync_width Sets the vertical sync width and saves it to the specified preset. Syntax #set_vert_sync_width param1 param2 Parameters param1 param2 Sync width [0 ... 9999] Preset [0 ...
Advanced Operation Commands #set_vert_total Sets the total number of vertical pixels and saves it to the specified preset. Syntax #set_vert_total param1 param2 Parameters param1 param2 Total pixels [0 ... 9999] Preset [0 ...
Advanced Operation Commands #set_vertical_mirror Enables or disables vertical mirroring. When set to on, the output image is flipped vertically. Syntax #set_vertical_mirror param1 Parameters param1 State param1 Description 0 Off 1 On Example #set_vertical_mirror 1 VERTICAL MIRROR SET TO On Related Commands #get_vertical_mirror #get_video_settings #set_horizontal_mirror page | 121 [0 ...
Advanced Operation Commands #set_vertical_shift Adjust the vertical position of the output image. Syntax #set_vertical_shift param1 Parameters param1 Vertical shift Example #set_vertical_shift -10 VERTICAL SHIFT IS SET TO -10 Related Commands #get_vertical_shift #get_video_settings #set_horizontal_shift page | 122 [-100 ...
VGA & Audio to HDMI Scaler/Converter 4 Appendix Menu System Summary..................................................................................... 126 Default Settings.................................................................................................. 132 Surface Mounting Instructions............................................................................ 133 Specifications.....................................................................................................
Appendix Menu System Summary OUTPUT SETUP OUTPUT RESOLUTION 640x480 60Hz 1680x1050 60Hz 720p 29.97Hz 640x480 75Hz 1680x1050 60Hz † 720p 25Hz 800x600 60Hz 1920x1080 60Hz † 1080i 60Hz 800x600 75Hz 1920x1200 60Hz 1080i 59Hz 1024x768 60Hz 1920x1200 60Hz † 1080i 50Hz 1024x768 75Hz Bypass 1080p 60Hz 1280x768 60Hz Auto-Detect 1080p 59.95Hz 1280x800 60Hz 480i 60Hz 1080p 50Hz 1280x1024 60Hz 576i 50Hz 1080p 30Hz 1280x1024 75Hz 480p 60Hz 1080p 29.
Appendix Menu System Summary OUTPUT COLORSPACE RGB 4:4:4 YCbCr 4:4:4 YCbCr 4:2:2 OUTPUT MODE HDMI DVI Auto Detect BACK Information Note the following frequency information: 23 Hz = 23.98 Hz 29 Hz = 29.97 Hz 59 Hz = 59.94 Hz † Denotes output resolution that supports reduced blanking. Boxes in green indicate the default setting.
Appendix Menu System Summary PICTURE CONTRAST [0 ... 100] BRIGHTNESS [0 ... 100] SATURATION [0 ... 100] HUE [0 ... 100] COLOR RANGE Full Limited COLOR TEMP. Warm Neutral COLOR BALANCE Red Channel Cool Green Channel EDGE ENH. Blue Channel Off SHARPNESS [0 ... 100] Mid Max BACK Boxes in green indicate the default setting.
Appendix Menu System Summary ADJUSTMENT UNDER/OVER SCN [-50 ... 50] 16:9 ASPECT RATIO 4:3 Stretch H. MIRROR On Source Off V. MIRROR On H. SHIFT [-100 ... 100] Off V. SHIFT [-100 ... 100] PHASE [Auto, 1 ... 64] BACK Boxes in green indicate the default setting.
Appendix Menu System Summary SYSTEM OSD TIMEOUT [Off, 5 ... 60] DISP. NOTIFY On Off INPUT RES. INFO Display Info FIRMWARE VER. Display Info FACTORY RESET Yes No BACK Boxes in green indicate the default setting.
Appendix Menu System Summary TEST PATTERNS White Window Cross H-Ramp Hatch WH-Ramp Color WV-Ramp Gray Off BACK EXIT page | 131
Appendix Default Settings Setting Value Aspect Ratio Source Brightness 50 Color Balance (Blue Channel) 50 Color Balance (Green Channel) 50 Color Balance (Red Channel) 50 Color Range Limited Color Temperature Neutral Contrast 50 Display Notifications On Edge Enhancement Off Horizontal Mirror Off Horizontal Shift Off Hue 50 OSD Timeout 5 seconds Output Color Space RGB 4:4:4 Output Mode Auto-Detect Output Resolution Auto-Detect Phase Auto Saturation 50 Sharpness 0 Tes
Appendix Surface Mounting Instructions The Sender and Receiver units can be mounted on any flat surface, as shown below (screws not included). There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for connection and disconnection of the DVI cables. For installation on a drywall surface, use a #6 drywall screw. When installing, it is recommended to use the center hole on a stud.
Appendix Specifications Connectors, Controls, and Indicators Video Input • 1 x VGA HD-15, female Video Output • 1 x HDMI Type A 19-pin, female Audio • 1 x 3.
Appendix Index A Active pixels horizontal 95 vertical 114 Aspect ratio 28, 55, 85 Audio Input 3 B Back porch horizontal 96 vertical 115 Brightness 19, 56, 86 C Color balance 24, 87 range 22, 88 saturation 20, 110 temperature 23, 89 Commands 50 #factory_reset 53 #fw_upgrade 54 #get_aspect_ratio 55 #get_brightness 56 #get_color_balance 57 #get_color_range 57, 58 #get_color_temp 59 #get_contrast 60 #get_display_notify 61 #get_edge_enhance 62 #get_firmware_version 63 #get_horizontal_mirror 64 #get_horizontal
Appendix Index D O Default settings 132 Display notify 37, 91 Operating Notes v OSD timeout 36, 103 Output color 14, 104 mode 16, 105 resolution 12, 106, 108 video 80, 81 Overscan 27, 113 E Edge enhance 25, 92 F Factory reset. See Resetting the unit Features vi Firmware displaying 40 Front porch horizontal 97 vertical 116 H P Packing list vi Phase 35 Picture settings 73 Pixel active. See Active pixels clock 109 total horizontal 101 Porch back.
Index Sync polarity horizontal 99 vertical 118 width horizontal 100 vertical 119 T Table of Contents viii Technical Support iv Test patterns 42, 112 Timing preset 77 U Underscan 27, 113 Upgrading the firmware 54 USB interface 48 COM port. See COM port: installing V Vertical mirror 31, 121 Vertical shift 34, 122 Video settings.
*Preferred Stretch it. Switch it. Split it. Gefen’s got it. ® 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.