080P DVI to HDSDI Pro Scaler GEF-DVI-2-HDSDIPRO User Manual www.gefenpro.
ASKING FOR ASSISTANCE Technical Support: Telephone Fax (818) 772-9100 (800) 545-6900 (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday Pacific Time. Write To: Gefen LLC c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefenpro.com support@gefenpro.com Notice Gefen LLC reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Connecting and Operating the DVI to HDSDI Pro Scaler 4 5 6 7 8 9 10 Wiring Diagram Panel Layout - Front Panel Panel Descriptions Panel Layout - Back Panel Panel Descriptions IR Remote Layout / Description IR Remote Description 11 IR Remote Installation 12 IR Remote Configuration 13 Menu Functions 13 General 14 Patterns 15 Output 18 Input 20 Picture 22 Layout 22 Aspect 25 Specifications 26 Warranty
INTRODUCTION Congratulations on your purchase of the DVI to HDSDI Pro Scaler. Your complete satisfaction is very important to us. GefenPRO In the realm of video distribution, certain features are invaluable in a commercial or broadcast environment. Accommodations such as a build-in power supply and flat black rack-mount enclosures set GefenPRO apart from our traditional products.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE DVI TO HDSDI PRO SCALER • On power-up, the DVI to HDSDI Pro Scaler will automatically detect the format of the input signal. • The DVI to HDSDI Pro Scaler contains a master and a slave DVI to HDSDI Scaler unit. Both Scaler units are controlled using the IR Remote Control Unit. To view the built-in menu system for the master unit, press the Menu button once on the IR Remote Control Unit.
FEATURES Features: • Input and Output Resolutions up to 2048x1080 • 10-bit resolution for greater precision and dynamic range • Proprietary 10-bit motion adaptive video de-interlacing with edge interpolation for HD / SD formats • Frame rate conversion to / from any refresh rate • Fully integrated sprite based multi-plane OSD controller • Advanced noise reduction and detail enhancement • Test Pattern mode with color bars and cross hatch patterns • Color correction • Noise Reduction • Detai
PANEL LAYOUT Front Panel 3 2 1 4
PANEL DESCRIPTIONS Front Panel 1 IR Window 1 (Primary Board) Receives signals from the IR Remote Control unit. 2 IR Window 2 (Secondary Board) Receives signals from the IR Remote Control unit. 3 Power Indicator This LED indicator will glow red when the power is turned on.
PANEL LAYOUT Back Panel 13 12 11 14 10 9 8 7 4 6 5 6
PANEL DESCRIPTIONS Back Panel 4 RS-232 Serial Port Connects to the RS-232 control device. The DVI to HDSDI Pro Scaler may be controlled using this port. See page 26 for more information. 5 5V DC Locking Power Connector Connects the included 5V DC Locking Power Supply to this receptacle. 6 DVI Input Port (Primary Board) Connect the DVI source device to this port. 7 Reference In Connector 1 Connect an external clock to this connector.
CONNECTING AND OPERATING THE GEFENPRO DVI TO HDSDI PRO SCALER How to Connect the GefenPRO DVI to HDSDI Pro Scaler 1. Connect two (2) DVI sources to the GefenPRO DVI to HDSDI Pro Scaler using the supplied DVI cables.. 2. Connect up to two (2) HDSDI devices to the outputs. 3. Apply power to the source and HDSDI devices first then apply power to the product.. The DVI source will be converted to HDSDI and then scaled on the output.
IR REMOTE LAYOUT RMT-8HDS-IR Remote Control 9 8 1 2 7 3 6 4 5 1 Up Cursor Button Moves the selection cursor Up, when using the built-in menu system. 2 Left Cursor Button Moves the selection cursor to the Left, when using the On-Screen Display menu system. 3 Down Cursor Button Moves the selection cursor Down, when using the built-in menu system. 4 Source Button Not used. 5 Output Button Pressing this button to cycle through the following Output Modes: 480i, 576i, 720p, and 1080i.
IR REMOTE LAYOUT 6 Menu Button Displays the built-in menu system. 7 Right Cursor Button Moves the selection cursor to the Right, when using the On-Screen Display menu system. 8 Enter Button Confirms the current action. 9 Activity Indicator This LED will be activated momentarily each time a button is pressed.
IR REMOTE INSTALLATION Installing the IR Remote Control Battery 1. Remove the battery cover on the back of the IR Remote Control unit. 2. Insert the included battery into the open battery slot. The positive (+) side of the battery should be facing up. 3. Replace the battery cover. The Remote Control unit ships with two batteries. One battery is required for operation and the other battery is a spare.
IR REMOTE CONFIGURATION Resolving IR Code Conflicts In the event that IR commands from other remote controls conflict with the supplied IR remote control unit, changing the remote channel will alleviate this issue. The IR remote control unit has a bank of DIP switches for setting the remote IR channel. The DIP Switch bank on the IR remote control unit is located underneath the battery cover.
USING THE IR REMOTE CONTROL UNIT Controlling Master and Slave Units The DVI to HDSDI Pro Scaler contains a master and a slave unit. The built-in menu system is controlled using the IR Remote Control Unit. To view the built-in menu system for the master unit, press the Menu button once on the IR Remote Control Unit. To bring up the built-in menu system for the slave unit, press the Menu button twice. See the illustration below for details.
MENU FUNCTIONS General > Save Configuration Saves the current configuration of the Scaler (Input format, Output format, etc). These settings are restored at power-up. Changes can be made to the current settings and then saved using the Restore Default Configurations function (below). General > Restore Default Configuration Restores the Scaler to the factory default settings.
MENU FUNCTIONS Patterns > Color Bars Displays the Color Bar pattern using the built-in pattern generator. Patterns > Cross Hatch Displays the Hatch Pattern using the built-in pattern generator.
MENU FUNCTIONS Output > Output Format Selects the Output resolution. See page 27 for supported output timings. Output > Link Configuration Dual Link configuration: Single Link, Dual Link YCbCr, or Dual Link RGB.
MENU FUNCTIONS Output > Genlock Reference The video signal can be synced (“genlocked”) to an external clock or video input using the Reference In connector. In order to use Genlock, the external clock must be a multiple of four (4) of the source timing. Output > Language Localizes the On-Screen Menu to either English or French.
MENU FUNCTIONS Output > Gamma Correction Allows adjustment of the Gamma coefficient, in addition to changing to the sRGB color space or other custom color tables. Input > Video Format Selects the input video format. By default, this option is set to Auto-Detect.
MENU FUNCTIONS Input > Input Graphic Format Selects the input graphic format. This should only be used if using a nonstandard timing which the DVI to HDSDI Pro Scaler does not recognize. Input > Clean Aperture Controls the zoom on the input signal. Zooming the image can be controlled using individual axis.
MENU FUNCTIONS Input > Remote Channel Changes the IR channel of the DVI to HDSDI Pro Scaler. The IR channel range is 0 - 3. NOTE: The IR channel can only be changed when using the Master Menu. Picture > Image Colour Adjusts the color levels on the output signal.
MENU FUNCTIONS Picture > Detail Enhancement Adjusts the detail / sharpness of the image. The noise threshold can also be changed. Picture > Noise Reduction Digitally reduces noise in the image.
MENU FUNCTIONS Picture > Motion Threshold Sets the intra-frame motion detection threshold for the de-interlacer. Video artifacts are sometimes introduced when creating a progressive frame from interlaced frames. Use this function to set the motion threshold used by the motion-detection algorithm when de-interlacing. Picture > Color Range Adjusts between limited RGB and full-range RGB.
MENU FUNCTIONS Layout > Size and Position Adjusts both the vertical and horizontal size and position of the output signal. Aspect > Full Screen Stretches the output signal to fit the entire screen.
MENU FUNCTIONS Aspect > Letter / Pillar Box Sets the aspect ratio on the output signal to fit the letter box or pillar box format. Aspect > Panoramic Panoramic Zoom feature.
MENU FUNCTIONS Aspect > Extract This function extracts a sub-window of the input signal. Use the Extract Size parameter to define the window size based on the percentage of the input. Use the Horizontal and Vertical parameters to select the area of the window to be extract. Aspect > Through Defines a sub-window that is always centered on the screen. The position of the sub-window is relative to the full picture.
RS-232 CONTROL The GefenPRO DVI to HDSDI Scaler Pro can accept commands through the RS-232 serial communications port located on the rear panel. RS-232 can be used to control many of the product’s features which are also controlled using the IR Remote Control Unit. Refer to the HDSDI RS-232 Serial Communications Manual on the Gefen web site for details on using the RS-232 interface.
SUPPORTED RESOLUTIONS Input Video Formats Supported: 480i 720p/50 1080p/23.98 2K-p/23.98 480p 720p/59.94 1080p/24 2K-p/24 576i 720p/60 1080p/25 576p 1035i/59.94 1080p/29.97 720p/23.98 1035i/60 1080p/30 720p/24 1080i/50 1080p/50 720p/25 1080i/50M 1080p/50M 720p/29.97 1080i/59.94 1080p/59.
SPECIFICATIONS Input Video Bandwidth...............................................................................165 MHz Output Video Bandwidth................................................................. 2 x 1.485 Gbps Maximum Input Resolution.....................................................................2048x1080 Maximum Output Resolution.............................2048x1080 with Dual Link HD-SDI DVI Input Connector......................................................................
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
Rev A1 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefenpro.com fax: 818-772-9120 support@gefenpro.com Pb This product uses UL listed power supplies.