DVI FM 2000 GEF-DVI-FM2000 User Manual DVI FM 2000 GEF-DVI-FM2000 User Manual
ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday, Pacific Time Write To: Gefen, LLC c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefenpro.com support@gefenpro.com Notice Gefen, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation without prior written notice.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender unit Layout 5 Sender unit Descriptions 6 Receiver unit Layout 7 Receiver unit Descriptions 8 Connecting the DVI FM 2000 9 Wiring Diagram 10 Specifications 11 Warranty CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender unit Layout 5 Sender unit Descriptions 6 Receiver unit Layout 7 Receiver unit Descriptions 8 Connecting the DVI FM 2000 9 Wiring Diagram 10 Specifications 11 Warranty
INTRODUCTION Congratulations on your purchase of the GefenPRO DVI FM 2000. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE DVI DUAL LINK FIBER EXTENDER • The DVI Dual Link Fiber Extender only uses multi-mode SC fiber cables. ATTENTION: Multi-mode fiber optic cable with a core diameter 50 or 62.5 microns is required, in order to extend to distance of 1000 feet (300 meters). • The included power supply is required for the Receiver unit. However, if the source does not supply enough power to the Sender unit, then an optional power supply (Gefen part no.
FEATURES Features • Extends Dual Link DVI up to 1000 feet (300 meters) using multi-mode (50 or 62.5 micron) fiber optic cable. • Supports HD resolutions up to 1080p Full HD. • Supports VESA resolutions up to 1920 x 1200 (WUXGA) and 3840 x 2400 (WQUXGA). • Optical signal transmission provides improved immunity from electromagnetic interference (EMI). • Supports HDCP pass-through.
SENDER UNIT LAYOUT Bottom Front 2 3 1 Back 4 4 SENDER UNIT LAYOUT Bottom Front 2 3 1 Back 4 4
SENDER UNIT DESCRIPTIONS 1 Status This LED indicator will glow bright blue, indicating that there is a valid connection between the Sender unit and Receiver unit. This LED will glow red when there is an interruption in the signal between the Sender unit and the Receiver unit. 2 Power Receptacle Connect the optional 5V DC power supply to this receptacle only if the source does not supply enough voltage to power the Sender unit. In most situations, the power supply will not be required.
RECEIVER UNIT LAYOUT Bottom Front 2 3 1 Back 4 6 RECEIVER UNIT LAYOUT Bottom Front 2 3 1 Back 4 6
RECEIVER UNIT DESCRIPTIONS 1 Status This LED indicator will glow bright blue, indicating that there is a valid connection between the Receiver unit and Sender unit. This LED will glow red when there is an interruption in the signal between the Receiver unit and the Sender unit. 2 Power Receptacle Connect this cable to the included 5 V DC power supply. 3 SC Fiber Connectors Connect two SC Fiber Optic cables from the Receiver unit to the Sender unit.
CONNECTING THE DVI FM 2000 How to Connect the DVI FM 2000 1. Connect the Dual Link DVI source to the Sender unit. 2. Connect the Dual Link DVI display to the Receiver unit. 3. Connect the Sender unit and Receiver unit together using two SC multi-mode fiber optic cables. IMPORTANT: On the bottom of both the Sender unit and Receiver unit, each fiber optic port is identified by the letter A or B.
WIRING DIAGRAM Wiring Diagram for the DVI FM 2000 ® FIBER OPTIC CABLE Sender Dual-Link DVI Source Receiver Dual-Link DVI Display GEF-DVI-FM2000 9 WIRING DIAGRAM Wiring Diagram for the DVI FM 2000 ® FIBER OPTIC CABLE Sender Dual-Link DVI Source Receiver Dual-Link DVI Display 9 GEF-DVI-FM2000
SPECIFICATIONS Maximum Pixel Clock................................................................................................................2 x 165 MHz Input Video Signal...........................................................................................................................1.2V p-p Input DDC Signal......................................................................................................................5V p-p (TTL) DVI Connector (Sender / Receiver)........................
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications. The two year warranty is only valid on new products purchased as of January 2007.
Rev A4 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefenpro.com fax: 818-772-9120 support@gefenpro.com This product uses UL listed power supplies. Rev A4 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefenpro.com This product uses UL listed power supplies. fax: 818-772-9120 support@gefenpro.
