Extender for HDMI w/POL GTB-HDBT-POL GTB-HDBT-POL-BLK User Manual gefentoolbox.
ASKING FOR ASSISTANCE Technical Support: Telephone Fax (818) 772-9100 (800) 545-6900 (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday through Friday, Pacific Time Write To: Gefen, LLC. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefentoolbox.com support@gefentoolbox.com Notice Gefen, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation without prior written notice.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Unit Layout 5 Sender Unit Descriptions 6 Receiver Unit Layout 7 Receiver Unit Descriptions 8 Connecting the Extender for HDMI w/POL 8 Wiring Diagram 9 Bi-Directional IR (Controlling the Source) 11 Bi-Directional IR (Controlling the Display) 13 Network Cable Wiring Diagram 14 Wall Mounting Instructions 15 Specifications 16 Warranty
INTRODUCTION Congratulations on your purchase of the Extender for HDMI w/POL. Your complete satisfaction is very important to us. About Gefen We specialize in total integration for your home theater, while also focusing on going above and beyond customer expectations to ensure you get the most from your hardware. We invite you to explore our distinct product line. Please visit http://www.gefen.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE EXTENDER FOR HDMI W/POL • CAT-5e or CAT-6 cables should not exceed 230 feet (70 meters). • Shielded (STP) CAT-5 or CAT-6 is recommended. However, unshielded (UTP) CAT-5 or CAT-6 is acceptable, depending on cable quality, but is not the top choice. Care should always be given to keep these cables away from power lines and other electromagnetic interference sources.
FEATURES HDMI Features Supported • Resolutions up to 1080p Full HD • 12-bit Deep Color • LPCM 7.
SENDER UNIT LAYOUT Front 1 2 Back 5 3 7 4 6 4
SENDER UNIT DESCRIPTIONS 1 IR Out Connect the included single infrared IR emitter (Gefen part no. GTB-IREMIT) from this jack to the IR sesnor window of the source. 2 Link Connect a CAT-5e/CAT-6 cable from the Sender to the Receiver unit 3 24V DC Connect the included 24V DC power supply to this connector and plug the AC power cord into an available electrical outlet. Only use the power supply shipped with this unit.
RECEIVER UNIT LAYOUT Front 1 2 Back 4 6 3 5 6
RECEIVER UNIT DESCRIPTIONS 1 IR Out Connect a single g infrared IR emitter (Gefen ( part no. GTB-IREMIT) from this jack to the IR sensor window of the HDTV display. 2 Link Connect a CAT-5e/CAT-6 cable from the Sender to the Receiver unit 3 Power/HDCP Indicatior This LED will turn on once the included 24V DC power supply has been connected. If HDCP is present, the LED will be lit in solid blue. If HDCP is not detected, the LED will flash blue/amber.
CONNECTING THE EXTENDER FOR HDMI W/POL How to Connect the Extender for HDMI w/POL 1. Using the included locking HDMI cable, connect a Hi-Def source to the HDMI Input port on the Sender unit. 2. Connect an HDTV display to the HDMI Output port on the Receiver unit using another HDMI cable. 3. Connect a CAT-6 cable from the Link jack on the Sender unit to the Link jack on the Receiver unit up to 230 feet (70 meters). A CAT-5e cable can be used to extend up to 198 feet (70 meters).
CONNECTING AND OPERATING THE EXTENDER FOR HDMI W/POL How to Connect the Bi-Directional IR Bi-Directional IR The Bi-Directional IR feature allows two simultaneous methods of control: Control of the source device and control of the display. The source device can be controlled from the viewing location by connecting an IR Extender (Gefen part no. EXT-RMT-EXTIRC) to the Receiver unit. The display can be controlled from the source location by connecting a PACS / Mini PACS to the Sender unit.
CONNECTING AND OPERATING THE EXTENDER FOR HDMI W/POL 3. To control the source from the display location, point the included IR remote control at the IR Extender connected to the Receiver unit. The IR signals are transmitted from the Receiver to the Sender unit over the CAT-5e/CAT-6 cable.
CONNECTING AND OPERATING THE EXTENDER FOR HDMI W/POL How to Connect the Bi-Directional IR Bi-Directional IR Controlling the Display In the example below, we will be setting up IR control for the display from the source location. The following illustrations assume all A/V devices have already been connected. See page 8 for details. 1. For IR control of a display from the source location, connect a 3.5mm-to3.
CONNECTING AND OPERATING THE EXTENDER FOR HDMI W/POL 3. To control the display from the source location, point the included IR remote control at the PACS or MIni PACS connected to the Sender unit. The IR signals are transmitted from the Sender to the Receiver unit over the CAT-5e/CAT-6a cable. Refer to the PACS or Mini PACS User Manual for more information on using IR commands. EXT-PACS Source DV D TAS VT ? 3 _ HDMI Cable 9 0 6 8 5 7 2 4 1 Source Remote 3.
NETWORK CABLE WIRING DIAGRAM Gefen recommends the TIA/EIA-568-B wiring option. Please adhere to the table below when field terminating cable for use with Gefen products. Pin Color 1 Orange / White 2 Orange 3 Green / White 4 Blue 5 Blue / White 6 Green 7 Brown / White 8 Brown 12345678 CAT-5, CAT-5e, and CAT-6 cabling comes in stranded and solid core types. Gefen recommends using solid core cabling. CAT-6a cable is also recommended.
WALL MOUNTING INSTRUCTIONS The GefenToolbox Extender for HDMI w/POL should be mounted vertically on a wall or inside / outside a cabinet with wood / drywall screws as shown in the diagram above. There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for connection and disconnection of the HDMI cable. For installation on a drywall surface, use a #6 drywall screw.
SPECIFICATIONS Maximum Pixel Clock................................................................................225 MHz Video Input Connector (Sender)..............(1) HDMI Type-A, 19-pin, female, locking Video Output Connector (Receiver)........(1) HDMI Type-A, 19-pin, female, locking Link Connectors (Sender / Receiver).........................................(1) RJ-45, shielded Power/HDCP Indicator LED: ..................................................Bi-color: Blue/Amber IR Extender Port (Receiver):..
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
*MA-GTB-HDBT-POL* Rev A1 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefentv.com Pb This product uses UL or CE listed power supplies. fax: 818-772-9120 support@gefentv.