3GSDI Audio Embedder 4K Ultra HD Extender w/ RS-232 and 2-way IR GTB-UHD2IRS-ELRPOL-BLK User Manual Release A2
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this product near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install or place this product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Warranty Information Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
Contacting Gefen Technical Support Technical Support (818) 772-9100 (800) 545-6900 8:00 AM to 5:00 PM Monday - Friday, Pacific Time Fax (818) 772-9120 Email support@gefen.com Web http://www.gefen.com Mailing Address Gefen, LLC c/o Customer Service 20600 Nordhoff St. Chatsworth, CA 91311 Product Registration Register your product here: http://www.gefen.com/kvm/Registry/Registration.
Operating Notes • CAT-5e (or better) cables should always be used. • The 4K Ultra HD Extender w/ RS-232 and 2-way IR will extend 1080p Full HD up to 495 feet (150 meters) and is limited to 8-bit color. 4K x 2K resolution can be extended up to 330 feet (100 meters). See Distance Setting (page 14) for more information. • Power Over Line (POL) is a Gefen proprietary technology that provides power to the Receiver unit over a single CAT-5e (or better) cable.
Features and Packing List Features • Extends 4K Ultra HD (3840 x 2160 @ 30 Hz, 8-bit color), RS-232, and bidirectional IR, up to 330 feet (100 meters) over a single CAT-5e cable (or better) • Extends HDMI at 1080p Full HD, RS-232, and Bi-Directional IR, over a single CAT-5e (or better) cable up to 495 feet (150 meters) at 8-bit color or up to 330 feet (100 meters) at 12-bit deep color • Supported HDMI Features ►► HDCP ►► 12-bit Deep Color ►► LPCM 7.
Features and Packing List Packing List The following items are shipped with the 4K Ultra HD Extender w/ RS-232 and 2-way IR. If any of these items are not present in the box when you first open it, immediately contact your dealer or Gefen. • • • • • • • • 1 x 4K Ultra HD Extender w/ RS-232 and 2-way IR (Sender unit) 1 x 4K Ultra HD Extender w/ RS-232 and 2-way IR (Receiver unit) 1 x 6 ft. locking HDMI cable (M-M) 1 x 6 ft.
Table of Contents 1 Getting Started Introduction............................................................................................................ 2 Sender unit..................................................................................................... 2 Receiver unit.................................................................................................. 4 Installation..............................................................................................................
4K Ultra HD Extender w/ RS-232 and 2-way IR 1 Getting Started Introduction............................................................................................................ 2 Sender unit..................................................................................................... 2 Receiver unit.................................................................................................. 4 Installation.....................................................................................
HDMI Power HDMI Power IR In HDMI Power IR Out Link IR Out RS-232 RS-232 Link IR Out RS-232 Link 5 6 7 page | 2 IR In w/RS-232 w/RS-232 w/RS-232 andand 2-way and 2-way 2-way IR IRIR 4K4K 4K Ultra Ultra Ultra HD HD HD S SS ELR-POL ELR-POL ELR-POL Extender Extender Extender 3 24V DC 2 24V DC 1 IR In 24V DC Getting Started Introduction Page Title Sender unit 4
Getting Started Introduction Page Title ID Name Description 1 24V DC Connect the included 24V DC power supply to this power receptacle. 2 Power This LED indicator will glow bright blue and will remain illuminated as long as the power supply is connected to the Sender unit. See Power LED Status (page 10) for details on LED status messages. 3 HDMI Use the included HDMI cable to connect an Ultra Hi-Def source to this HDMI port. 4 IR In Connect a mini-mono 3.
RS-232 Link IR Out RS-232 Link IR Out RS-232 Link 5 6 page | 4 IR Ext HDMI Power IR Ext HDMI IR Ext HDMI w/RS-232 w/RS-232 w/RS-232 andand 2-way and 2-way 2-way IR IRIR 2 4K4K 4K Ultra Ultra Ultra HD HD HD R RR ELR-POL ELR-POL ELR-POL Extender Extender Extender IR Out 4 Power 1 Power Getting Started Introduction Page Title Receiver unit 3
Getting Started Introduction Page Title ID Name Description 1 Power This LED indicator will glow bright blue and will remain illuminated as long as the power supply is connected to the Receiver unit. See Power LED Status (page 10) for details on LED status messages. 2 HDMI Connect an HDMI cable between this port and an Ultra HD display. 3 IR Ext Connect the included IR extender to this port. 4 IR Out Connect an IR emitter (Gefen part no.
Getting Started Installation Connection Instructions ►► Video 1. Connect the included HDMI cable between the Ultra Hi-Def source and the HDMI port on the Sender unit. 2. Connect an Ultra HD display to the HDMI port on the Receiver unit using another HDMI cable. ►► CAT-5 3. Connect a CAT-5e (or better) cable, up to 495 feet (150 meters) from the Link port on the Sender unit to the Link port on the Receiver unit. Information Resolution will affect extension distance.
Installation Getting Started Sample Wiring Diagram CAT-5e CABLE HDMI CABLE IR RS-232 CABLE 4K Ultra HD Source Automation Device (Up to 495 ft) RS-232 Controlled Device 4K Ultra HD Display IR Input IR Emitter Receiver Sender IR Extender IR Emitter GTB-UHD2IRS-ELRPOL-BLK Information The wiring diagram, shown above, requires an additional IR emitter (Gefen part no. EXT-IREMIT).
4K Ultra HD Extender w/ RS-232 and 2-way IR 2 Basic Operation Power LED Status................................................................................................ 10 Sender unit LED........................................................................................... 10 Receiver unit LED........................................................................................ 11 IR Control.......................................................................................................
Basic Operation Power LED Status The Power LED indicator on the Sender and Receiver unit provides basic information on the current status of the 4K Ultra Extender w/ RS-232 and 2-way IR. Sender unit LED Status Description Off • Sender unit is not powered. • Check the power supply. • Link is established between Sender and Receiver unit. • The Sender unit is receiving the source signal. Flashing blue / orange • Non-HDCP content is being received by the Sender unit.
Basic Operation Power LED Status Receiver unit LED Status Description Off • Receiver unit is not receiving power from Sender unit. Inspect CAT-5 cable between Sender and Receiver unit. • Check the power supply. • Link is established between Sender and Receiver unit. • Receiver unit is powered and is receiving the source signal from the Sender unit. Flashing blue / orange • Non-HDCP content is being transmitted to the Receiver unit.
Page Title Controlling the Source from the Viewing Location 1. Connect the included IR extender to the IR Ext port on the Receiver unit. 2. Connect the included IR emitter from the IR Out port on the Sender unit to the IR sensor on the source device.
Controlling the Display from the Source Location 1. Connect the 3.5mm mini-mono connector from the IR In port on the Sender unit to the automation system. 2. Connect the included IR emitter from the IR Out port on the Receiver unit to the IR sensor on the display.
Basic Operation DIP Switch Configuration Distance Setting This product passes through the display’s EDID to the source. If the display is capable of accepting Deep Color, the source must be manually configured to output 8-bit color. This is only applicable when using 4K x 2K resolutions and “long-run” modes. The distance setting is controlled using a DIP switch on the bottom of the Receiver unit.
4K Ultra HD Extender w/ RS-232 and 2-way IR 3 Appendix Surface Mounting Instructions.............................................................................. 18 Network Cable Diagram....................................................................................... 19 Specifications....................................................................................................... 20 Index...........................................................................................................
Appendix Surface Mounting Instructions The Sender and Receiver units can be mounted on any flat surface, as shown below (screws not included). There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for connection and disconnection of the HDMI cables. For installation on a drywall surface, use a #6 drywall screw. When installing, it is recommended to use the center hole on a stud.
Appendix Network Cable Diagram Front of RJ-45 Connector 1 2 3 4 5 6 7 8 Gefen recommends the TIA/EIA-568-B wiring option. Use the following table when terminating cables in the field.
Basic Operation Specifications Supported Formats Video • • • 4K x 2K 1920 x 1200 (WUXGA) 1080p Full HD Audio • • • 7.1 Linear PCM Dolby® TrueHD DTS-HD Master Audio™ HDMI (Sender) • 1 x HDMI Type A, 19-pin, female HDMI (Receiver) • 1 x HDMI Type A, 19-pin, female Link (Sender / Receiver) • 1 x RJ-45, shielded, female IR In (Sender / Receiver) • 1 x 3.5mm, female IR Out (Sender / Receiver) • 1 x 3.
Basic Operation Index C T Connection Instructions 6 Table of Contents viii Technical Support iv D W DIP Switch Configuration 14 Warranty Information iii Wiring Diagram 7 Distance setting. See DIP Switch Configuration F Features vi I Installation 6 IR Control 12 controlling the display 13 controlling the source 12 L LED Status 10 “long-reach” mode.
*Preferred Stretch it. Switch it. Split it. Gefen’s got it. ® 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.
