Wireless VGA Extender LR GTV-WVGA-LR User Manual www.gefentv.
ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday PST (Pacific Standard Time) Write To: Gefen Inc. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen Inc. reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice. Wireless VGA Extender LR is a trademark of Gefen Inc.
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Sender Panel Layout 5 Sender Panel Descriptions 6 Receiver Panel Layout 7 Receiver Panel Descriptions 8 Sender LED Layout 9 Receiver LED Layout 10 Connecting And Operating The Wireless VGA LR 12 Specifications 13 Warranty
INTRODUCTION Congratulations on your purchase of the Wireless VGA LR. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies.
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE WIRELESS VGA LR • The Wireless VGA LR will accept component video signals (YPbPr) up to 1080p. However, 1080i and 1080p signals will be down scaled and transmitted at 1280x720. Please see the table at the bottom of this page for a list of input and output resolutions and framerates. • For better transmitting quality, please do not place units into cabinets or cupboards that will reduce the wireless transmitting signal.
FEATURES Features • Wireless extension of VGA up to 100 feet • • • • Video Input Formats Supported: Max. VGA: 1280x1024@60Hz Max. Y/Pb/Pr: 1080p@60Hz SVideo, Composite: 480i@60Hz, 576i@50Hz • • • Video Output Formats Supported: Max. VGA: 1280x1024@60Hz Max.
SENDER PANEL LAYOUT Front Panel 2 1 3 Back Panel 4 5 4 6 7 8 4 4 9 10 11
SENDER PANEL DESCRIPTIONS 1 Power Switch This switch will toggle the main power on and off. 2 Source Selector Button This button will cycle through the available input video sources. The cycle is outlined below: VGA Component S-Video Composite 3 Channel Selection Button This button will cycle through the available radio channels. There are 4 channels to choose from. This feature is useful when a certain channel is oversaturated and another needs to be used.
RECEIVER PANEL LAYOUT Front Panel 2 1 3 Back Panel 4 5 4 6 7 8 6 4 9
RECEIVER PANEL DESCRIPTIONS 1 Power Switch This switch will toggle the main power on and off. 2 Output Selector Button This button will cycle through the available output choices. The cycle is outlined below: VGA Component 3 Channel Selection Button This button will cycle through the available radio channels. There are 4 channels to choose from. This feature is useful when a certain channel is oversaturated and another needs to be used.
SENDER LED LAYOUT LED Wi-Fi Color Green Red CH 1~ CH 4 Blue VGA Blue YPbPr Blue S-Video Blue Composite (CVBS) Blue Behavior Indication On Wireless function is active. Blinking Data receiving. Blinking Data transmitting overflow. On Wireless channel firm. Blinking Switch channels. On VGA source is active. Blinking Switching sources. On YPbPr source is active. Blinking Switching sources. On S-Video source is active. Blinking Switching sources.
RECEIVER LED LAYOUT LED Wi-Fi Color Green Red CH 1~ CH 4 Blue VGA Blue YPbPr Blue Behavior Indication On Wireless function is active. Blinking Data receiving. Blinking Data transmitting overflow. On Wireless channel firm. Blinking Switch channels. On VGA source is active. Blinking Switching sources. On YPbPr source is active. Blinking Switching sources.
CONNECTING AND OPERATING THE WIRELESS VGA LR How to Setup the Wireless VGA LR Sender Unit 1. Connect source devices to the Wireless VGA LR sender unit. The sender unit has the following connection options: VGA Component S-Video Composite 2. Connect a single analog audio source to the Wireless VGA LR sender unit using a 3.5mm mini-jack audio cable. 3. Connect one or both of the following output device types to the Wireless VGA LR receiver unit: VGA (VGA cable included) Component 4.
CONNECTING AND OPERATING THE WIRELESS VGA LR If the Wi-Fi LED remains on (green) and does not blink, the sender and receiver units are not linked and video/audio is not being transmitted. When this occurs, video will not be displayed and the output will remain on a blue screen. This text will be displayed: “No Wi-Fi connection” Try moving the sender or receiver unit’s location until a link is established and the Wi-Fi LED is blinking green. The Wi-Fi LED may occasionally blink red.
SPECIFICATIONS Wireless Standard ...................................................................... IEEE 802.11b/g/n Antenna Type .......................................................... External Dipole antenna 2dBi PCM Encoding ................................................................... 48KHz 16-bit sampling Power Supply .......................................................................... 2 x 12V @ 1A each Audio Inputs/Outputs ....................................................... 3.
WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
Rev A5 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 www.gefentv.com Pb fax: 818-772-9120 support@gefentv.