Instruction Manual Rack Power Distribution Unit BRE and VRTE Series Geist 1821 Yolande Ave., Lincoln, NE 68521 800.432.3219 | 402.474.3400 | F: 402.474.4369 | www.geistglobal.
Contents Specifications ....................................................................................................................3 Overview 3 Environmental 3 Electrical 3 Receptacle Ratings 3 Detachable Power Supply Cords 4 EMC Verification 4 Installation .......................................................................................................................5 Instructions 5 Guidelines 5 Mounting .......................................................................................
Specifications Overview The BRE and VRTE Series products are Power Distribution Units (PDU) intended for connection to a 20 Amp AC Mains circuit. The BRE and VRTE Series PDUs connect to AC Mains power through an IEC-320 C19 style AC Inlet. These PDUs are rated 125/250 Vac, 50/60 Hz, 16 A and can optionally be configured with single pole thermal breakers or hydraulic-magnetic circuit breakers used for supplementary over-current protection of the output receptacles 1.
Detachable Power Supply Cords Use only detachable power supply cords of the appropriate size and type, as stated below, with the PDU. Use only with light PVC sheathed flexible cords (according to IEC 60227) or ordinary tough rubber-sheathed flexible cords (according to IEC 60245) that terminate in an attachment plug meeting local/national code requirements. For Global units use a minimum 1.5 mm2 nominal conductor cross-sectional area detachable power supply cord with ratings of 300 V and 75 °C.
Installation Instructions 1. Using appropriate hardware, mount PDU to rack (see Mounting section for additional instructions. 2. Plug PDU into de-energized 20 Amp branch circuit receptacle3. 3. Connect devices into PDU’s output receptacles. It is recommended that the devices are turned off until all devices are connected to PDU 4. Turn on branch circuit to energize PDU. 5. Power on devices. Sequential power up is recommended to avoid high inrush current.
Mounting Full Length Bracket Using the full length bracket, mount PDU to rack as shown Mini "L" Brackets (SLB-4) Using the mini “L” brackets, attach PDU to rack as shown GM1003 Rev 2 6 Rev Date: 7/28/2014
Vertical Extension Brackets (VCB-1) Using the vertical extension brackets, attach PDU to rack as shown Toolless Mounting Hardware (11621) Secure toolless mounting buttons to PDU as shown. Use toolless buttons with key-holed slots built into cabinet or with optional Geist key-holed brackets.
Toolless Full Length Bracket (TLFL) Using full length toolless bracket and toolless mounting buttons, attach PDU to rack as shown Single Side Mount 2 Unit Brackets (TSMX2) Using single side mount 2 unit brackets and toolless mounting buttons, attach PDU to rack as shown GM1003 Rev 2 8 Rev Date: 7/28/2014
Offset/Side Mount Brackets (EZB-1) Using the offset/side mount brackets, attach PDU to rack as shown.
Flush Mount Brackets (FM) Using flush mount brackets, attach PDU to rack as shown Adjustable Mount Brackets (AM) Using adjustable mount brackets, attach PDU to rack as shown GM1003 Rev 2 10 Rev Date: 7/28/2014
Panel Mount Brackets (PM) Using panel mount brackets, attach PDU to rack as shown 23" Conversion Mounting Brackets (23-RM) Using conversion mounting brackets, attach 19” PDU to 23” rack as shown GM1003 Rev 2 11 Rev Date: 7/28/2014
Cable Mount Bracket (CMB-1) Attach cable mount bracket to PDU as shown; use tie-wraps to secure cords to bracket 19" Horizontal/Panel Mount Brackets (7938) Using the 19” horizontal/panel mount brackets, attach PDU to rack as shown GM1003 Rev 2 12 Rev Date: 7/28/2014
Optional Local Monitoring Power Meter The Geist PM-1 power meter is a low-power, high accuracy meter capable of measuring true RMS Current, Voltage, Power, and Power Factor. These values are individually shown on an easy to read, 4-digit LED Display, which continuously scrolls through the four different measured values. Each one of these displayed parameters is defined below. The Power Meter will automatically begin cycling through the displayed values when the PDU is connected to AC Mains power.
Service/Tech Support Service and Maintenance No service or maintenance is required. Do not attempt to open the PDU or you may void the warranty. No serviceable parts inside. It is recommended that power be removed from the unit before installing or removing any equipment. More Technical Support http://www.geistglobal.com (800) 432-3219 Email: support@geistglobal.com Or contact your distributor.
Table of Figures Full Length Bracket................................................................................................................................................................... 6 Mini "L" Brackets (SLB-4) ...................................................................................................................................................... 6 Vertical Extension Brackets (VCB-1) ...............................................................................................
Revision History Revision 1.0 Date 4/23/2009 2.