User's Manual
Table Of Contents
- Contents
- Tables
- Figures
- 1 Introduction
- 2 Interface Characteristics
- 2.1 Application Interface
- 2.2 RF Antenna Interface
- 2.3 Sample Application
- 3 Operating Characteristics
- 3.1 Operating Modes
- 3.2 Power Up/Power Down Scenarios
- 3.3 Power Saving
- 3.4 Power Supply
- 3.5 Operating Temperatures
- 3.6 Electrostatic Discharge
- 3.7 Blocking against RF on Interface Lines
- 3.8 Reliability Characteristics
- 4 Mechanical Dimensions, Mounting and Packaging
- 5 Regulatory and Type Approval Information
- 6 Document Information
- 7 Appendix
Cinterion
®
ELS61-AUS Hardware Interface Description
5 Regulatory and Type Approval Information
94
ELS61-AUS_HID_v00.031 2016-06-03
Confidential / Preliminary
Page 89 of 102
5 Regulatory and Type Approval Information
5.1 Directives and Standards
ELS61-AUS is designed to comply with the directives and standards listed below.
It is the responsibility of the application manufacturer to ensure compliance of the final product
with all provisions of the applicable directives and standards as well as with the technical spec-
ifications provided in the "ELS61-AUS Hardware Interface Description”.
1
Table 21: Standards of Australian Type Approval
1. Manufacturers of applications which can be used in the US shall ensure that their applications have a
PTCRB approval. For this purpose they can refer to the PTCRB approval of the respective module.
Table 20: Directives
1999/05/EC Directive of the European Parliament and of the council of 9 March 1999
on radio equipment and telecommunications terminal equipment and the
mutual recognition of their conformity (in short referred to as R&TTE Direc-
tive 1999/5/EC).
The product is labeled with the CE conformity mark
2002/95/EC (RoHS 1)
2011/65/EC (RoHS 2)
Directive of the European Parliament and of the Council
of 27 January 2003 (and revised on 8 June 2011) on the
restriction of the use of certain hazardous substances in
electrical and electronic equipment (RoHS)
GCF-CC v.3.61 Global Certification Forum - Certification Criteria
NAPRD.03
Version 5.28
Overview of PCS Type certification review board Mobile Equipment Type
Certification and IMEI control
PCS Type Certification Review board (PTCRB)
FCC Certification (CFR
47 Part 15, 22, and 24)
Federal Communication Commission Certification
Code of Federal Regulations (CFR) 47
PART 15 - RADIO FREQUENCY DEVICES
PART 22 - PUBLIC MOBILE SERVICES
PART 24 - PERSONAL COMMUNICATIONS SERVICES
EN 301 511 V9.0.2 Global System for Mobile communications (GSM); Harmonized standard
for mobile stations in the GSM 900 and DCS1800 Bands covering essen-
tial requirements under article 3(2) of the R&TTE Directive (1999/5EC)
EN 301 908-1 V5.2.1 Electromagnetic compatibility and Radio spectrum Matters (ERM); Base
Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-
Generation cellular networks; Part 1: Harmonized EN for IMT-2000, intro-
duction and common requirements, covering essential requirements of
article 3.2 of the R&TTE Directive
EN 301 908-2 V5.2.1 Electromagnetic compatibility and Radio spectrum Matters (ERM); Base
Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-
Generation cellular networks; Part 2: Harmonized EN for IMT-2000, CDMA
Direct Spread (UTRA FDD) (UE) covering essential requirements of article
3.2 of the R&TTE Directive