Installation Instructions

ManualsBrandsGemini ManualsCar alarm7463

DESCRIPTION

The systems 7463 and 7462 are modular systems which consists of an alarm unit and one audible external

siren. These alarm systems can be installed on vehicles with 12V battery with negative to earth.

FUNCTIONS

7463

- Self-powered unit and remote controlled alarm with dynamic code (frequency 433.92 MHz).

- Blinker and external siren.

- Negative control for additional siren.

- Central door locking, windows and electric sunroof control (for vehicles with “Pac -comfort” system).

- Perimetric, volumetric (K1 and K2 model ) protection.

- Alarm memory through audible and optical signalisations.

- Remote controlled “PANIC” function.

- Emergency disarming through “PIN” code.

- Accessorial functions programmable with the transmitter.

7462- As 7463 not self-powered.

INSTALLATION INSTRUCTIONS

- Connect the power wire to the battery positive terminal and the earth directly to the bodywork of

the vehicle.

- Connect always the alarm GREEN-BROWN wire to the door pin switches.

- Connect always the alarm GREEN wire to the bonnet switch.

- On catalysed vehicles the engine immobilisation must be carried out on the fuel pump.

- If an ultrasonic module is used, the ultrasonic heads must be positioned on the left and right

windscreen pillar of the rear windows, turned to the passenger’s compartment and away from the

facia outlet.

- After the electric connections have been carried out, programme the functions through the

transmitter and change the manufacturer “PIN” code.

WIRING CONNECTIONS

(DISCONNECT THE BATTERY NEGATIVE TERMINAL AND ONLY RECONNECT AFTER THE INSTALLATION IS

COMPLETE)

FUNCTION WIRE COLOUR

Earth ðð BLACK initialled “M”

Battery positive terminal ðð BLACK initialled “R”

Command for external relais ðð 2 x BLACK initialled “H”

Ignition live ðð YELLOW

Direction indicator lights ðð 2 x ORANGE

Door and boot pin switches ðð GREEN-BROWN

Bonnet switch ðð GREEN

Positive alarm armed ðð PINK

Sensors inlet ðð GREEN-BLACK

Negative outlet control additional siren

ðð YELLOW-BLACK

Central door locking ðð YELLOW-BLUE, RED-BLUE, YELLOW-GREY,

RED-GREY, YELLOW-BROWN, RED-BROWN

Sound unit ðð BLUE and GREY

NOTE: in the wiring harness there are 2 connectors; connect the 4-pin connector to the ultrasonic or high

frequency module and the 2-pin connector to the LED.

The terminals of the Blue and Green wire of the sound unit must be positioned in the White connector of

the unit on positions 10 and 20. In the kit there is an extension of the BLACK initialled V wire for the

connection of the bonnet b utton.

FUNCTIONS PROGRAMMABLE THROUGH THE TRANSMITTER

FUNCTIONS MANUFACTURER’S PROGRAMMING

1 Arming / disarming audible tones Activated

2 Panic alarm / Car Finder Panic activated

3 Current sensor De-activated

4 Automatic alarm rearming /

Automatic locking of the doors

De-activated

5 Passive alarm arming De-activated

6 CDL pulse time Selected time 1 second

7 Comfort time De-activated

8 CDL opening double pulse De-activated

INLET IN THE PROGRAMMING PROCEDURE OF THE ACCESSORIAL FUNCTIONS.

Disarm the alarm with the transmitter, open the vehicle’s door (keep it opened) and turn the ignition

key to ON: the LED will switch on for 0,5 seconds.

During this period (led switched on) press at the same time on both transmitter’s button.

The confirmation of the programming phase inlet is given by the Led switching on with fix light followed

by two acoustic signalling; one with low frequency (BOP) and one with high frequency (BIP).

The system now is in the programming modality and it is waiting for the controls that will be sent with

the transmitter’s buttons.

CHANGE OF THE FUNCTIONS PROGRAMMING.

Any selection will be signalled by two different audible tones:

REMOTE CONTROL PUSH BUTTON N°1 : HIGH FREQUENCY AUDIBLE TONE (BIP). TO SET ON THE

CURRENT FUNCTION AND SELECT THE NEXT ONE.

REMOTE CONTROL PUSH BUTTON N°2 : LOW FREQUENCY AUDIBLE TONE (BOP). TO SET OFF THE

CURRENT FUNCTION AND SELECT THE NEXT ONE.

Push Button N° 1: Set ON

ARMING / DISARMING AUDIBLE TONES

Push Button N° 2: Set OFF

Push Button N° 1: Panic set ON

Car finder set OFF

PANIC ALARM / CAR FINDER

Push Button : Panic set OFF

Car finder set ON

Push Button N° 1: Set ON

CURRENT SENSOR

Push Button N° 2: Set OFF

Push Button N° 1: Set ON

AUTOMATIC ALARM REARMING / AUTOMATIC

LOCKING OF THE DOORS

Push Button N° 2: Set OFF

Push Button N° 1: Set ON

PASSIVE ALARM ARMING

Push Button N° 2: Set OFF

Push Button 1: 6 seconds

CDL PULSE TIME

Push Button 2: 1 second

Push Button N° 1: Set ON

COMFORT TIME

Push Button N° 2: Set OFF

Push Button N° 1: Set ON

CDL OPENING DOUBLE PULSE

Push Button N° 2: Set OFF

Summary of content (5 pages)

PAGE 1
FUNCTIONS PROGRAMMABLE THROUGH THE TRANSMITTER DESCRIPTION The systems 7463 and 7462 are modular systems which consists of an alarm unit and one audible external siren. These alarm systems can be installed on vehicles with 12V battery with negative to earth. FUNCTIONS 7463 - Self-powered unit and remote controlled alarm with dynamic code (frequency 433.92 MHz). - Blinker and external siren. - Negative control for additional siren.
PAGE 2
OUTLET FROM THE PROGRAMMING PROCEDURE OF THE ACCESSORIAL FUNCTIONS. It is possible to leave any moment the programming procedure turning the ignition key to OFF. In this case it is obtained the memorisation of the condition for the changed functions and the confirmation of the previous condition for the unchanged functions.
PAGE 3
4) ALARM FOR CUT WIRES: 4 flashing of the direction indicator lights, of the Led and 4 audible signalling with low tone (BOP) at the same time of the optical signalling. 5) ALARM FOR EXTERNAL SENSORS/BONNET: 5 flashing of the direction indicator lights, of the Led and 5 audible signalling with low tone (BOP) at the same time of the optical signalling.
PAGE 4
Learning de-activation: To stop the learning, (after point 5), it is necessary to close the DOOR and the BONNET of the vehicle and to turn the ignition key to OFF. The system will signal the outlet from the learning procedure with an optical / audible signalling which consists of one audible low tone (BOP) and one flashing of the direction indicator lights. NOTE: the alarm system, for working security reasons, has not a procedure to erase the devices previously memorised.
PAGE 5
Alarm Triggering LED R Pink Brown Green /black Ultrasonic Red Conne TECHNICAL DATA Working Voltage Current absorption Working temperature 7059 T 9÷16VDC 2,5 mA -30°C +85°C AMP Connector Sensitivity Adjustment White Conne 7059 Sensor - Fitting Positions DESCRIPTION OF THE 7059 MODULE (K2 models). GEMINI 7059 protects the vehicle detecting attempts to break into the passenger’s compartment by the emission of an electromagnetic field (frequency = 2,45 GHz).