Bluetooth Sound Bar with Built-In Subwoofer CHT912 INSTRUCTION MANUAL
FCC Warnings WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
AC/DC adapter 1. Placing on the table Ventilation When placing the Sound Bar on an entertainment center, bookshelf, or any type of enclosed space, be sure to allow at least 2-3 inches of space around the Sound Bar for ventilation. If the Sound Bar is enclosed in a tight space, without ventilation, heat generated from the Sound Bar could produce a potential heat hazard. 2. Mounting the Speaker Bar onto a wall We recommend having this speaker professionally mounted.
You will need : • Tape Measure • Manual or Electric drill • Level • Pencil 2.1. Mounting on the wooden wall You should use 2 pieces of short screws 2 pieces of EVA 1. Use the TAPE MEASURE to decide how high you’d like to hang the sound bar on the wall. The sound bar must be hung within 5 feet of an AC power outlet for the attached AC power cord to reach. 2. Mark the position of the mounting screws on the wall using a pencil. 3. Line the LEVEL up on both of your mark sure they are level.
2.2. Mounting on the dry wall You should use 2 pieces of short screws 2 pieces of EVA 2 pieces of plastic tubes 8VH WKH 7$3( 0($685( WR GHFLGH KRZ KLJK \RXƍG OLNH WR KDQJ WKH 6SHDNHU %DU RQ WKH ZDOO 7KH 6281' %DU PXVW EH KXQJ ZLWKLQ IHHW RI DQ $& SRZHU RXWOHW IRU WKH DWWDFKHG $& SRZHU FRUG WR UHDFK 0DUN WKH SRVLWLRQ RI WKH PRXQWLQJ VFUHZV RQ WKH ZDOO XVLQJ D SHQFLO /LQH WKH /(9(/ XS RQ ERWK RI \RXU PDUN VXUH WKH\ DUH OHYHO ,I WKH\ UH QRW DGMXVW WKH PDUNV DV QHHGHG WR PDNH
1. REMOTE SENSOR: Ensure this area is not covered or blocked by any object. 2. STANDBY button: Press to turn the speaker bar off or on. 3. SOURCE button: Press to switch between Bluetooth receiver, AUX, LINE in and FM. 4. VOLUME +: Press to increase the volume. 5. VOLUME -: Press to decrease the volume 6. MUTE: Press to mute the volume. 7. STANDBY Indicator. 8. FM Indicator. 9. Bluetooth Indicator. 10. AUX Indicator. 11. LINE IN Indicator. 12. FM antenna port. 13. AUX L/R IN: To insert RCA cable. 14.
1. STANDBY button: Press to turn the unit on or off. 2. BT button: Press to switch to Bluetooth mode. 3. SCAN button: Press to scan for available radio stations in FM Radio mode. 4. MUSIC button: Press to switch to the EQ optimized for music. 5. TREBLE button: Press to adjust the treble up or down. 5. VOL- button: Press to decrease the volume. 6. AUX button: Press to switch to AUX mode. 7. MUTE button: Press to mute the volume. 8. LINE button: Press to switch to LINE In mode. 9.
PUSH OPEN CR2025 Li th CR iu 20 m SC 3V 25 Cel l UL 1. It includes one 2025 button cell battery. (pre-installed) 2. Removes the transparent sheet.
Audio Inputs (1) Using the Stereo RCA Inputs When connecting two products using an RCA Cable, match the colored ports with the same colored connection. Before use, disconnect any cables connected to the LINE IN. 1. Connect the RCA Cable to the RCA Stereo Inputs located on the back of the unit, and to the audio outputs on the television. 2. Press the STANDBY button to power on the unit. 3. Press the AUX button on the remote or SOURCE button on the unit repeatedly to enter aux mode. 4.
4. When successfully paired and connected, blue LED indicator will be light only and stop blinking. 5. If your device should become upaired or it is unable to connect, blue LED indicator will continue flashing and blinking. Repeat the above steps to try to pairing. 6. If the initial set up connection is succesful, the next time the speaker is turned on , the speaker will automatically pair to the last device it was connected with . NOTE: 1. The Bluetooth speaker only connects to device at a time .
Problem What to do No power Check that the power is switched on at the wall. Check if the power cord is properly connected to the power outlet. No sound Check that the volume control is NOT at minimum setting. Check that it is NOT set to mute. Function disturbed If none of the above solutions work, then switch off and unplug your Speaker system, leaving it for 2 minutes and then switching it back on again. The remote control won' t work Inspect or replace the batteries.
Power Source :……………………. AC120V, 60Hz Power Source of Remote Control:……DC 3V, 1X CR2025 battery (Included) Power Consumption:…………………………………….< 1W Audio Power : Woofer …………………………………............ 30W Left Channel ……………………………...........10W Right Channel………………………….............10W Radio Coverage …..………………………...............…. FM 87.5-108.0 MHz Impedance of Speakers : Woofer ……………………………….….......… 8 Ohm,18W x 2 Left Channel …………………………….......... 4 Ohm,12W Right Channel…………………………........….