WALL MOUNTABLE 2.0-CHANNEL BLUETOOTH SOUNDBAR SPEAKER USER MANUAL JSBW-210 PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
DEAR JENSEN® CUSTOMER Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level.
IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1.
16. Battery shall not be exposed to excessive heat such as sunshine, fire or the like 17. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. 18. Do not attempt to dismantle, open or repair this product yourself. If a fault occurs, seek advice from your local qualified service technician or contact the distributor via the telephone number at the back of this instruction manual. 19. Caution marking and nameplate are located on bottom of product.
ACCESSORIES 1 x AC Adaptor 1 x Remote Control, 1 x Stereo Audio Connection Cable with 3.5mm stereo plugs 1 x User Manual 1 x RCA Connection Cable 1 x Wall Mount Template 2 x Spaces 2 x Anchors (For Wall Mounting) 2 x 55mm Screws (For Wall Mounting) INSTALLATIONS Placing the JSBW-210 on a table Ventilation When placing the Sound Bar on an entertainment center, bookshelf, or any type of enclosed space, be sure to allow at least 2-3 inches of space around the Sound Bar for ventilation.
1. Use the supplied wall mounting template to make drill hole marks on the wall. Make sure the marks are level before drilling. 2. Attach the Spaces to the wall by screwing the supplied flat head screws directly into the marks that you have made on the wall as shown above. 3. Place the sound bar onto the mounting screw heads. Make sure the sound bar is attached firmly to the wall. Mounting the JSBW-210 on wall Use a power drill to make pilot holes for the plastic anchors 1.
LOCATION OF CONTROLS MAIN UNIT Front View 1 Back View Right Hand Side View 6
1. MODE INDICATOR LED 2. REMOTE INFRARED SENSOR 3. FM WIRE ANTENNA 4. OPTICAL INPUT JACK 5. AUX-IN 2 L/R RCA CONNECTORS 6. DC IN JACK 7. POWER ON/STANDBY ; MODE BUTTON 8. VOLUME + BUTTON 9. AUX-IN 1 JACK 10.
REMOTE CONTROL 1. POWER ON/STANDBY BUTTON 2. AUX IN 1 MODE BUTTON /PAIR BUTTON 3. BLUETOOTH MODE 4. FM MODE/SCAN BUTTON 5. MUSIC/MOVIE/VOICE SOUND EFFECT BUTTONS 6. TREBLE +/- BUTTONS 7. TUNE-/SKIP BACKWARD ; TUNE+/SKIP FORWARD BUTTON 8. AUX IN 2 MODE BUTTON 9. MUTE BUTTON 10. OPTICAL MODE BUTTON 11. CHANNEL UP (+)/DOWN (-) BUTTONS 12. VOLUME UP (+) / DOWN (–) BUTTONS 13. BASS +/- BUTTON 14.
GETTING STARTED CONNECTING THE JSBW-210 TO EXTERNAL AUDIO DEVICES You can connect the JSBW-210 audio input to the audio output of your television or DVD Player. Please see figure below. NOTE: 1. Make sure that the power is turned off when connecting or disconnecting the other devices. Make sure that the other devices are connected to the correct terminals. 2. This unit is not magnetically shielded and may cause color distortion on the screen of some TVs or video monitors.
Replacing the battery in the remote control: 1.) Press in on the side of the battery holder and pull the holder out of the remote. 2.) Removed the exhausted battery and then install 1 new “CR2025” lithium battery according to the polarity diagram on the battery compartment. 3.) Insert the battery holder into the remote control and make sure it locks into place. NOTE: Only use a well-known brand of battery to ensure the longest life and best performance.
LISTENING TO THE FM RADIO TUNING THE FM RADIO 1. Tap the /STANDBY button on the remote control or press and hold the /MODE button on main unit to turn on the unit. 2. Tap the FM/SCAN MODE button on remote control or tap the /MODE button on main unit repeatedly to select FM radio mode, the Mode Indicator LED turns to Yellow color. 3. Press and hold the FM/SCAN button on the remote control, unit will start to search stronger FM stations and store them automatically, yellow LED flashing.
NOTE: Automatic tuning depends on the signal strength of the broadcasting station, so weak stations may be skipped. You can manually tune to find the weak stations if a station gets skipped. With strong signals, the tuner may stop before it reaches the actual broadcast frequency, so you may need to manually tune for the best reception. RECALLING PRESET MEMORY CHANNELS In radio mode, recall the pre-set channels detected in FM Scan by pressing the CH+/button on remote control repeatedly.
2.) If your Bluetooth enabled device does not support A2DP, it will not play the music through the speaker, even after it's paired (linked). 3.) If you are pairing (linking) your computer to the JSBW-210 using Bluetooth, you may need to set the JSBW-210 as your computer’s default sound device. CONTROLLING THE MUSIC PLAYBACK ON YOUR BLUETOOTH DEVICE USING THE REMOTE CONTROL 1. Tap the /STANDBY button on remote control or press and hold the /MODE on main unit to turn on the unit. 2.
already in relative sound effect mode. In addition, you can adjust treble and bass effects by using the TREBLE & BASS +/buttons. NOTE: Press the MUSIC button on remote control, sound effect will be reset to the default (NORMAL) setting. The TREBLE and BASS settings will also be reset to the center position. MUTE (Remote Control Only) - Press the MUTE button on remote control to mute the sound output from speaker temporarily, the red LED will light and flash.
AUXILIARY INPUT This unit provides an auxiliary audio signal input jack for connecting external audio devices like MP3 players, CD players and listen to them through the speakers of this unit. 1. Use an audio cable (included) with one 3.5 mm stereo plug on each end of the cable. 2. Plug one end into the AUX-IN 1 jack on the right hand side (top panel) of main unit and the other end of the cable into the Line-out Jack or Headphone Jack of your external audio device. 3.
If the front panel becomes dirty or smudged with fingerprints it may be cleaned with a soft cloth slightly dampened with a mild soap and water solution. Never use abrasive cloths or polishes, as these will damage the finish of your unit. CAUTION: Never allow any water or other liquids to get inside the unit while cleaning. TROUBLESHOOTING GUIDE Should you experience difficulties in the use of this player please refer to the following chart or call 1-800-777-5331 for Product Service and Support.
Frequency Range Radio Band FM 87.5 ~ 108 MHz At Spectra, environmental and social responsibility is a core value of our business. We are dedicated to continuous implementation of responsible initiatives with an aim to conserve and maintain the environment through responsible recycling. Please visit us at http://www.spectraintl.com/green.htm for more information on Spectra’s green initiatives or to find a recycler in your area.
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $45.00 to cover the cost of repair, handling and return postage. All out of warranty returns must be sent prepaid. It is recommended that you contact SPECTRA first at 1-800-777-5331 or by email at custserv@spectraintl.com for updated information on the unit requiring service. In some cases the model you have may be discontinued, and SPECTRA reserves the right to offer alternative options for repair or replacement.
