Installation Guide

ManualsBrandsGemmy ManualsHalloween InflatablesThe Nightmare Before Christmas 7-ft x Lighted Mayor Of Halloween Town Halloween Inflatable

Rotating Airblown Inﬂatable

™

Assembly Instructions

STEP 1: MAIN BASE

• Place main base in desired display location and unfold the legs. Pull up the four corners

on the main base and lock them into position.

• Illustration 1: Thread main base power cord plug down through center of the main base.

• Plug main base power cord into power source.

• Make sure the switch on the top of the main base is in the OFF position

(ON position has red light).

STEP 2: SPIRAL GROUND STAKES

• Secure the main base to the ground using the spiral ground stakes. See Illustration 2.

Twist each stake through the legs of the main base and into the ground.

STEP 3: TETHER POLES

• Illustration 3: Assemble tether poles. Insert each tether pole into a corner of the main base,

with loop end outward.

STEP 4: AIRBLOWN

INFLATABLE

• Illustration 4: Ensure the four clips on the bottom of the fabric of the inﬂatable are

attached to the plastic legs on the base of the inﬂatable.

• Illustration 5: Ensure that the air intake on the inﬂatable unit is clear of fabric and

other obstructions and that the zipper is fully closed. Some inﬂatables have more than

one zipper.

• Illustration 6: Place Airblown

on main base, aligning the feet of the Airblown

base

to the coordinating spaces on the main base. Secure using four hand screws.

• Illustration 7: Wrap Airblown

power cord around the two hooks on top of the main

base to keep clear of rotation. Make sure the Airblown

is zipped up. Plug Airblown

power cord into main base power cord receptacle to begin inﬂation.

STEP 5: TETHERS

(Illustration 10: Please note, ﬁnal tethers should form an upside down “V” shape.)

• Illustration 8: Clip two tethers to one of the fabric loops on the Airblown

. Repeat on

opposite side of Airblown

• Use one pair of clipped tethers and lace each end through a corresponding plastic loop

in a tether pole, forming an upside down “V” shape (see Illustration 10). Repeat with the

other pair of clipped tethers.

• Tie each tether to its tether pole, adjusting as needed to ensure the Airblown

is vertical

and straight. This may take several adjustments. When complete, each tether should be

taut.

• Illustration 9: Wrap excess cord around the tether pole.

STEP 6: SWITCH ON

Press the switch on the main base to the ON position to begin rotation. see Illustration 11.

Rotation begins after three minutes to allow for any ﬁnal adjustments.

PRO TIP: Before starting STEP 4, make note of where the switch is located

on the main base so you can easily ﬁnd it when the Airblown

is inﬂated.

NOTE: To prevent power cord damage, the Airblown

rotates 350° in one direction

then reverses to rotate 350° in the other direction. Also, if the Airblown

encounters an

obstruction, it will rotate the other direction.

Illustration1 Illustration 2

Illustration 7 Illustration 8

Illustration 9

Illustration 11

PARTS

Airblown

Inﬂatable (1)

Main Base (1)

Spiral Ground

Stakes (4)

Tether Poles (4)

Tethers (4)

Hand Screws (4)

Illustration 4

Illustration 5

ASSEMBLY STEPS

Please allow about 15-20 minutes to assemble a Rotating Airblown Inﬂatable

™

Illustration 3

Illustration 6

Illustration 10

Summary of content (1 pages)

PAGE 1
Rotating Airblown Inflatable™ Assembly Instructions PARTS Airblown® Inflatable (1) Tethers (4) Spiral Ground Stakes (4) Main Base (1) Tether Poles (4) Illustration1 Illustration 2 Illustration 3 Illustration 4 Illustration 5 Illustration 6 Illustration 7 Illustration 8 Illustration 9 Illustration 10 Hand Screws (4) ASSEMBLY STEPS Please allow about 15-20 minutes to assemble a Rotating Airblown Inflatable™. STEP 1: MAIN BASE • Place main base in desired display location and unfold the legs.