THE LINKSYS GROUP, INC. 17401 Armstrong Ave., Irvine, CA 92614 TEL: (949) 261-1288 FAX: (949) 261-8868 Wireless Presentation Gateway WPG11 User’s Manual FCC ID: MXF-PS910815 Draft 2.0 – Apr.
Copyright statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording, or otherwise without the prior written consent of the publisher. Printed in Taiwan, April 2002 IMPORTANT INFORMATION Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
R&TTE Compliance Statement This equipment complies with all the requirements of the DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety Notification Your Wireless Presentation Gateway should be placed in a safe and secure location. To ensure proper operation, please keep the unit away from water and other damaging elements. Please read the installation guide thoroughly before you install the Wireless Presentation Gateway. The Wireless Projector should be repaired by authorized and qualified personnel only Please do not try to open or repair the Wireless Presentation Gateway yourself.
TABLE OF CONTENTS 1. Introduction………….………………………………………………………… 7 2. Hardware Installation ………………………………………………………….8 3. WPG11 Web Configuration ………. …………………………………………10 4. EPS player Program .…….……………………………………………………14 5. Troubleshooting.………..…………………………………………………..….20 6.
1. INTRODUCTION 1.1 Congratulation on Your Purchase of the Wireless Presentation Gateway The Wireless Presentation Gateway features state of the art technology that helps bring wireless capability to a conventional projector. You can now access the projector through a wireless network effortlessly without being constrained by the physical layout of a wired connection. The Wireless Presentation Gateway allows for multiple dynamic wireless connections from several PCs.
2. HARDWARE INSTALLATION 2.1 Front panel EPS11 has 3 LED indicators on its front panel. Refer to the following table for the meaning of each indicator. LED’s Power Traffic Link Status Description. Power status indicator. A steady light indicates power is being applied to the EPS11 unit. Data traffic indicator. A blinking light indicates that at least one person is doing a presentation via EPS11 on the projector. Wireless link status indicator.
irrespective of the network setting of your computer. The image of your computer desktop should transfer to the Projector via EPS11 immediately. The architecture of a communication network with EPS11 is shown below.
3. WPG11 WEB Configuration 1. Open the web browser and hyperlink to the default IP address “169.254.1.1”. An authentication dialog box will pop up like the one shown below. 2. Enter the correct username and password in the dialog window. The default username and password are both “admin”.
3. After a successful logon, the window first displays the values of the current WPG11 setting, including “Projector Name”, “Projector Password” and “Firmware version”. 4. Click the Setup tab on top of the window to move to the device setup page. Enter the desired “Projector Name”, “Projector Password” and “Admin Password” for your device in the appropriate fields. (You can only input at most 8 characters in the “Projector Password” field.) 5. When done, click the Save button.
The device will now begin saving the new setting and display this progress. When the progress bar at the bottom of the web browser counts to 100%, the setting is saved. 6. Click the Update tab to navigate to the firmware-update page. Next, click the Browser button to select the new firmware image from your local file system. When done with firmware selection, click the Update button to replace your current firmware with the selected file. The update process may take some seconds to complete.
7. You can click the Help tab to obtain more information on this WPG11 at any time. Or you can click the Exit tab to close the web browser.
4. EPS player Program This section provides instructions on how to install and run the EPS player software program on your PC. The software program enables you to connect your PC to the EPS11 and use the projector from your PC. 4.1 Installing the EPS player Program a. Running the setup program A copy of the client setup program, EPSsetup.exe, is included on the accompanying CD-ROM that comes with the EPS unit. Double-click on the EPSsetup.exe file to open the Installation Wizard.
(iii) On the Installation Completed window, click the Finish button to complete the setup process. (iv) When the installation is completed, a shortcut will be created on the desktop. You can double-click this shortcut to run the “EPS player” program. Please read Section 2 for more information on EPS player.
4.2 Running the EPS player (i) Double-click the icon program. on the desktop to run the “EPS player” (ii) On the Welcome ! window, check the Only use Ad-Hoc mode checkbox to make EPS player connect to the EPS unit in Ad-Hoc mode. Uncheck this box to keep the player’s original setting. When done, click the Next button to proceed. (iii) The EPS player is now searching for every EPS unit on the network. The search may take several seconds.
(Graph 1) (Graph 2) 16
(iv) On the Presentation Station Found window, click the EPS Selection combo box button to select the EPS station of your choice. Then click the Next button to proceed. (The player is now configuring the selected EPS based on your EPS player’s network setting. If configuration is completed, the EPS player will show the Presentation Options window (Graph 3). Otherwise, the Presentation Station Couldn’t be found window is shown.
Take Control of the Presentation Station button Click this button to start presentation. Give Control to Another User button Click this button to give up presentation. Exit button Click this button to exit the EPS player program. 4.3 Context menu and Hot-keys When the EPS player is executed, a tray icon will be created on the taskbar. Users can right-click on this icon to invoke its context menu.
5. Troubleshooting There is no EPS11 Client Utility on your PC Please insert the Installation Disc of EPS11 and click the Setup button. The Installation Wizard should automatically install the client utility and place a shortcut on your desktop. Double-click this shortcut to begin desktop image presentation.
Specifications Product Name：Wireless Presentation Gateway Model Name：EPS11 FCC ID: MXF-PS910815 Country to be certified: FCC ID grant, CE certification Items 1. Modulation type Contents DSSS 2. How to move out the modulation Software Control 3. Number of channels Default: 11, Europe: 13 2412, 2417, 2422, 2427, 2432, 2437, 4. Carrier frequency of each channel 2442, 2447, 2452, 2457, 2462, 2467, 2472MHz 5. Bandwidth of each channel 5 MHz 6. IF & L.O. frequency IF=374 MHz, L.O.=2038∼2098 MHz 7.
