User's Manual

产品功能
无线耳机连接手机步骤
6.开启手机1无线功能，找到之前连接过的耳机，点击连接即可完成一拖二连接。
USB接口
按键功能操作
你手机与耳机之间的无线工作范围大约为10米，超出此距离，耳机有可能出现音质下降和失去连接。
◎支持连接无线设备播放音乐
◎支持无线连接高清晰通话
◎内置中文语音提示音
1.请将无线耳机和手机（或其他的连接设备）的距离在1米的范围内，越近越好
2.确保耳机在关机状态，长按多功能键约5秒直到红/蓝灯交替闪烁，此时进入配对状态，等待连接；
3.开启用户手机无线功能（或其他无线设备），并进行搜索或扫描，此时手机会搜索到附近所有的
无线设备，点选搜索到的耳机名称：型号详见外包装，并输入密码0000（目前大部分手机不需要密
码），成功配对连接后，耳机指示灯转为蓝灯闪动，表示配对连接成功！
多功能按键
指示灯
开机：长按多功能键约2秒开机
如何重新连接
关机：长按多功能键约3秒关机
1.你的耳机会尝试重新连接失去的连接。
配对模式：长按多功能键约5秒进入配对状态
接听/挂断：单击多功能键实现来电接听与挂断
来电拒接：来电时快速双击多功能键松开实现来电拒接
末码重拨：双击多功能键开启末码重拨
播放/暂停：播放音乐时单击实现播放暂停功能
◎支持同时连接两个设备，一拖二功能
2.如果耳机未尝试重新连接，请轻按一次多功能按钮或通过手机的无线设备菜单以手动方式重新连接。
单边无线耳机
LED指示状态
耳帽
产品说明书
◎配对状态：红蓝灯交替闪烁
◎配对成功：蓝灯慢闪烁
◎开机:蓝灯闪烁三次
◎关机：红灯常亮2秒
◎待机：蓝灯5秒闪烁1次
◎充电中亮红灯
手机一拖二连接步骤
麦克风
1.无线耳机关机情况下，长按多功能键大约6秒，直到耳机提示灯出现红蓝交替闪烁，进入被搜索状
态。
无线版本
支持协议
内置电池
Wireless V5.3.2
工作范围
通话时长
充电时间
0~10m(无障碍空间)
约4小时（80%音量）
约2小时
2.开启手机1的无线功能，搜索无线设备寻找耳机名称，点“配对”完成连接。
3.将手机1的无线关闭，长按耳机多功能键，直到亮红灯，关闭耳机。
4.再次打开无线耳机进入被搜索状态。
A2DP、AVRCP、HSP、HFP
锂电池-3.7V,70mAh
◎充满电亮蓝灯
5.打开手机2无线功能，搜索无线设备寻找耳机名称，点击“配对”完成连接。
搜索不到耳机
【1】 【2】 【3】 【4】 【5】
USB charging port Connect with phone
6.Turn on wireless function of phone1 to connect the earphone again.
Please keep earphone and phone1/2 within 10meters
Notes
Multi-function button
Indicator light
OPERATION
1.Place earphone with phone within 1meter,the closer the better;
2.Long press MFB until red and blue lights flash alternatively,in pairing status;
3.Turn on wireless function on the phone,search the earphone model,click to connect without any
passwords,when successfully connect indicator will turns to blue light flashes.
1.7 When earphone under pairing status,please connect earphone with your phone within two
minutes,otherwise it will automatically power-off;
·Power-on：Press MFB 2seconds
·Pairing：Press MFB 5seconds
·Power-off Press MFB 3seconds
Problems&Solution
·Answer phone call：Short press MFB 1time
·Reject phone call：Double click MFB
1.Couldn’t search earphone model on your phone
Reasons:
Tips：Please use the charger which is below 1A, please disconnect AC power
when full charged,please donot chargeearphones with powerbanks
·End phone call：Short press MFB 1time
WIRELESS EARPHONE
·Redial the last phone number：Double click MFB 1time
·Pause/Play：Short press MFB 1time
1.1 Earphone in power-off status;
Ear cap
Congratulations!Successfully connect,now you can listen music and dial
USER MANUAL Microphone
1.2 Something goes wrong with earphone procedure;
1.3 Something goes wrong with phone procedure.
Solution:
Indicator
Multi-points connection
·Pairing:Blue and red lights flash alternatively
·Power-on:Blue light flash 3times
·Pairing success:Blue light flash slowly
·Power-off:Red light is on for 2seconds
1.Long press earphone MFB until red and blue lights flash alternatively,in pairing status;
2.Turn on wireless function on the phone1,search the earphone model,click to connect;
3.Turn off wireless function of phone1,long press MFB to turn off earphone;
4.Long press earphone MFB until red and blue lights flash alternatively again,in pairing status;
5.Turn on wireless function on the phone2,search the earphone model,click to connect;
Wireless version Wireless V5.3 Working range 10meters
1.4 After power-off earphone,long press MFB until red and blue lights flash alternatively to active
earphone’s pairing status;
Wireless standard A2DP、AVRCP、HSP、HFP
Battery -3.7V,70mAh
Talk time About 4hours(80% volume)
DC5V-500mA Micro USB
·Standby:Blue light flash 1time every 5seconds ·Red light is on when in charging status
·Blue light is on when full charged
1.5 Re-set earphone;
Charging input
criteria
1.6 Reboot your phone,and erase all connect or pairing data on your phone.
【1】 【2】 【3】 【4】 【5】
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
【
6】