SpectroLED Baton LED STICK LIGHT USER MANUAL
THANK YOU FOR CHOOSING GENARAY SpectroLED INTRODUCTION The Genaray Baton is a bicolor wand-style LED light that provides even illumination along its entire length. The Baton’s simplicity and portability is surpassed only by its versatility. It packs up in its own carry bag and is light enough to take anywhere. Use it as a key light, an accent light, or for background ambience. As a handheld fixture, it can create dramatic indoor or outdoor effects for photo and video shoots.
· Please read and follow these instructions, and keep his manual in a safe place. · Handle the unit with care. · Keep this unit away from water and any flammable gases or liquids. · Clean the unit with only a soft, dry cloth. · Make sure the unit is powered off when plugging it into a power source. · Keep this unit away from children. · Use only the correct, recommended voltage. · Do not attempt to disassemble of repair the equipment.
Front BATON OVERVIEW 5-pin mini DMX in/out ports Threaded ring for battery handle 4 SpectroLED Baton LED Stick Light - USER MANUAL
Back LCD screen Product Overview Power button Mode button Up/Down buttons Magnet mount sockets Brightness preset buttons Color temperature preset buttons SpectroLED Baton LED Stick Light - USER MANUAL 5
Top LCD screen BATON OVERVIEW Power button Up/Down buttons Mode button Bottom 4-pin power input port 6 SpectroLED Baton LED Stick Light - USER MANUAL
Arca-Swiss style ballhead mount Product Overview Release knob Arca-Swiss style mount Ballhead tension knob Locking knob 5/8-inch receiver/11⁄8-inch stud SpectroLED Baton LED Stick Light - USER MANUAL 7
CONTENTS INCLUDE · Baton light fixture · AC adapter Contents · Power cable · DMX Cable · Magnet mounts · Arca-Swiss style ballhead mount · Carrying case · User manual 8 SpectroLED Baton LED Stick Light - USER MANUAL MOUNTING THE BATON ATTACHING THE ARCASWISS STYLE MOUNT 1. Loosen the release knob, and fit the back edges of the Baton into the grooves of the mount. 2. Tighten the release knob until secure.
The included ballhead can be mounted onto any light stand with a 5/8-inch stud. The 5/8-inch receiver has a passthrough, so the ballhead can be mounted horizontally or vertically. 1. Mount the Baton on a light stand with a 5/8-inch stud, and turn the locking knob until secure. 2. Adjust the orientation of the Baton by loosening the ballhead tension knob.
POWERING THE BATON USING THE BATON WITH AC POWER Instructions Important The Baton is a multivoltage fixture capable of running on 100 to 240 V, 50/60 Hz. The included cable has a 120 V, 50 Hz plug. To use this fixture with other voltages, you must use a plug adapter (sold separately). Connect the AC power adapter to the Baton with the 4-pin XLR cable, and use the power cable to connect the adapter to an outlet. Important! The 4-pin connector should easily attach.
TURNING ON THE BATON ADJUSTING THE COLOR TEMPERATURE Warning! When set to full brightness, the Baton is a powerful light. Do not look directly into the light while it’s being switched on. 1. Press the Mode button to enter color temperature mode. Press the ON/OFF button to turn on the Baton. ADJUSTING THE BRIGHTNESS The Baton starts up in brightness adjustment mode. Use the Up/Down buttons to adjust the brightness in 1% increments. Instructions OPERATING THE BATON 2.
USING DMX Instructions The Baton supports DMX-512, so the light’s settings can be remotely controlled from a DMX console. To set up DMX operation on the Baton, follow these steps: 1. Use the included 5-pin cable to attach a DMX controller to either one of the mini DMX ports. The other port will automatically become the output port. 2. Use the other mini DMX port to connect multiple lights. Note: If the Baton is the only light connected to the DMX controller, no DMX termination is necessary. 3.
DMX CONTROL 2 — 16 17 — 511 512 Corresponding Channels on DMX Console 1-1 Brightness 1-2 Color temperature 1-2 Brightness 1-3 Color temperature — 1-16 Brightness 2-1 Color temperature 2-1 Brightness 2-2 Color Temperature — 32-15 Brightness 32-16 Color temperature — Instructions DMX Address on LCD screen 1 SpectroLED Baton LED Stick Light - USER MANUAL 13
PRODUCT SPECIFICATIONS LIGHT FIXTURE Specifications Output Power: 20: 28 W 34: 58 W 53: 88 W Beam Angle: 110° Color Temperature: 2800 ±150 K to 6500 ±300 K Color Accuracy Standard: CRI: 95 to 98 TLCI: 95 Dimming: 100% to 10% Display: LCD Housing Material: Metal Photometrics @ 3ft.
CONNECTORS Specifications Power Input Connector: 4-pin male XLR DMX Connector: 5-pin mini male XLR MOUNTING Fixture Mount: 5/8 in. receiver 11⁄8 in.
ONE-YEAR LIMITED WARRANTY This Genaray product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.