SpectroLED 9 PRODUCT GUIDE Genaray SpectroLED 9 Guide | Page 1
INTRODUCTION Thank you for choosing Genaray. The Genaray SP-AD35 LED Light uses 500 LED lights installed on an 8.25” diameter circuit board array for an approximate output equivalent to 35 W. The light is balanced at 5600 K daylight temperature. The LED emits very little heat, eliminating the need to wait for it to cool off before handling. A variable dimmer knob on the back of the lamp will allow you to control the light output between 10% and 100%.
The light mounts onto any standard 5/8” light stand, and the mounting bracket articulates over 90° vertically. Uniquely featured with the Genaray LED is the umbrella socket built into the six o’clock position of the circuit board array. Diffuse the light from the array by inserting an umbrella (sold separately) through the umbrella socket. You may also use the included diffuser sock to fit around the circumference of the reflector. Additional diffuser socks are available as an accessory from Genaray.
Specifications SPECIFICATIONS • Light source – 500 Super Bright LEDs set at a 60° angle. • Reflector diameter – 9.
• Genaray SP-SD External Dimmer • Diffuser Sock • C-Stand with Turtle Base • Super Clamp • Air Cushioned Light Stand • Collapsible Circular Reflector Disc • 12 V Battery w/Cigarette Lighter Plug Adapter • 32” + Translucent Ubrella WARNINGS ⚠ ⚡ • Do not attempt to disassemble or repair the equipment – doing so will void the warranty, and Genaray will not be responsible for any damage. • Handle the unit with care. • Clean the unit with a soft dry cloth. • Keep this unit away from children.
Power switch Dimmer knob INSTRUCTIONS Remote dimmer Umbrella socket Two-pin connection Upper locking knob Lower locking knob Genaray SpectroLED 9 Guide | Page 6
MOUNTING THE LIGHT 2. Mount the LED light by fitting the mount onto the top of the light stand. 3. Tighten the lower locking knob on the mounting bracket to secure the LED light. USING THE DIMMER 1. Rotate the dimmer knob clockwise to increase the brightness to 100%. 2. Rotate the dimmer knob counterclockwise to decrease the brightness to 10%. Genaray SpectroLED 9 Guide | Page 7 Instructions 1. Loosen the lower locking knob on the mounting bracket of the LED light.
ADJUSTING THE ANGLE 1. Loosen the upper locking knob on the mounting bracket of the LED light. Instructions 2. Carefully adjust the articulation. 3. Tighten the upper locking knob to secure the new position. PLUGGING INTO AN AC POWER SOURCE 1. Power off the LED light by turning the power switch to the OFF position. 2. With the groove in the cable jack facing down, insert the jack into the two-pin connection on the back of the lamp. 3.
1. Be certain the power switches on both the LED fixture and the battery are in the OFF position. 2. With the groove in the cable jack facing down, insert the jack into the two-pin connection on the back of the lamp. 3. Rotate the locking collar on the jack clockwise to secure the connection. 4. Plug the male end of the cable into the battery socket. 5. Turn the LED light’s power switch to the ON position. 6. To turn the LED light on or off, use the battery’s power switch. 7.
MOUNTING AN UMBRELLA (SOLD SEPARATELY) Instructions 1. Insert the umbrella into the umbrella socket located in the bottom of the diameter within the LED array. 2. Adjust the umbrella as necessary. 3. The pressure from the socket itself will hold the umbrella in place. Visit our website at www.genaray.com for more Genaray accessories.
This GENARAY product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
© Copyright 2014 Genaray