SpectroLED STUDIO LIGHT USER MANUAL SpectroLED STUDIO LIGHT - USER MANUAL 1
SpectroLED INTRODUCTION Thank you for choosing a Genaray SpectroLED Studio Light. The SpectroLED Studio light features a sturdy metal housing and produces bright, consistent, professionalquality light in a compact form. The Studio series LED lights are available in 500-LED and 1012-LED versions. Each version comes in two variations: Daylight and Bi-Color. The Daylight version generates a 5600°K daylight-balanced light, and includes a tungsten filter to balance the light to 3200°K.
KEY FEATURES · Daylight version produces 5600°K light and includes a tungsten filter for 3200°K light · Bi-Color version has adjustable color temperature from 3200°K to 5600°K · Convenient touch-screen controls · Daylight version has dimming from 100% to 0% · Bi-Color version has dimming from 100% to 10% · Wireless remote control included · Removable mounting knuckle can be positioned for horizontal or vertical placement FEATURES · Powerful, lightweight 500-LED or 1012-LED fixture · Includes easily rem
CONTENTS INCLUDE CONTENTS · Genaray SpectroLED Studio fixture (500 or 1012 LEDs) · Two cable straps · Removable adjustable mounting knuckle with ratchet lock · User manual · Wireless remote control · Diffusion filter · Tungsten filter (Daylight version only) 4 SpectroLED STUDIO LIGHT - USER MANUAL · AC power cord and adapter · Carry case with shoulder strap · One-Year Limited Warranty
· Please read and follow these instructions, and keep this manual in a safe place. · Handle the unit with care. · Keep this unit away from water and all flammable gases or liquids. · Clean the unit with a soft, dry cloth. · Make sure the unit is powered off when plugging it into a power source. · Use only the correct, recommended voltage. · Do not attempt to disassemble or repair the equipment—doing so will void the warranty, and Genaray will not be responsible for any damage.
PRODUCT OVERVIEW Barndoors Led Array Magnetic Filter / Diffuser Mounts Mounting Knuckle 6 SpectroLED STUDIO LIGHT - USER MANUAL
SP-S-1000 Filters PRODUCT OVERVIEW SP-S-500 Filters Wireless Remote Control Locking Flange Large Locking Wheel Tightening Knob Ratchet Handle Magnetic Diffusion Filter Magnetic Tungsten Filter SpectroLED STUDIO LIGHT - USER MANUAL 7
Carry / Tilt Handle PRODUCT OVERVIEW Lcd Touch-Screen 4-Pin Power Jack Fuse Bay Gel Clips 8 Battery Plate Mounting Holes SpectroLED STUDIO LIGHT - USER MANUAL Power Switch
PRODUCT OVERVIEW Carry / Tilt Handle Battery Plate Mounting Holes 4-Pin Power Jack Lcd Touch-Screen Fuse Bay Gel Clips Power Switch SpectroLED STUDIO LIGHT - USER MANUAL 9
MOUNTING THE LIGHT INSTRUCTIONS · The removable mounting knuckle has a ratchet handle for quick tightening and loosening. It can be placed anywhere along any of the four sides of the fixture, giving you precise control over placement of the light. · To use the mounting knuckle, insert the locking flange into the enlarged section of the mounting groove that's along each side of the fixture. Slide the knuckle to the position you desire, and securely lock the large locking wheel.
POWERING THE LIGHT · The Studio light operates on any 120/220 VAC circuit using the included adapter. A built-in fuse (located between the power switch and the power connector on the back of the fixture) provides overcurrent protection for electric circuits, and two spare fuses are included. To change the fuse, use a small screwdriver to turn the cover of the fuse bay counterclockwise while pressing in. Remove the old fuse, insert a new fuse into the bay, and replace the cover.
TOUCH-SCREEN CONTROL INSTRUCTIONS · A touch-screen on the back of the fixture gives you convenient control of dimming (for the Daylight and the Bi-Color versions) and of color temperature (for the Bi-Color version). Simple arrow controls are easy to read and easy to use. The fixture comes with a protective film covering the touch-screen. Please remove this protective film before using the light. · On the touch-screen there are two sections, the Dimmer and the Color Temperature.
REMOTE CONTROL A wireless remote control is included with each Studio light. It can control both the Daylight and Bi-Color light fixtures, as well as multiple fixtures at once. You can use the remote to increase or decrease light output, adjust color temperature (Bi-Color version only), change light output in increments of 25% (Daylight versions only), and turn the power on or off. GROUPING AND SYNCHRONIZING LIGHTS · In order to use the remote, it first has to be synchronized to the fixture.
USING THE REMOTE Note: Since the remote controls the Daylight and Bi-Color fixtures differently, it is not recommended to sync a single remote to both types of lights. Rather, use at least two separate remotes in a setup incorporating both Daylight and Bi-Color lights. · To remove a light from a group or to assign a different remote to an existing light, you will have to re-sync the desired light to a new remote. First turn off any lights that you do not wish to change.
Bi-Color Synchronize A + D (hold) A + D (hold) Dimmer up A A Dimmer down B B Color temperature up – C Color temperature down – D Power On/Off D C+D Audio Confirmation Beep On/Off A+B A+B Dimmer 25% Down* C – · To replace the remote control's 23A battery, use a small Phillips-head screwdriver to remove the screw on the back. Lift up the back plate, and swap out the old battery for a new one. Replace the back and securely tighten the screw in place.
MODIFYING THE LIGHT OUTPUT INSTRUCTIONS · The light from this Studio fixture can be controlled and changed according to the effect you want. Barndoors and filters can shape the light or change the color or contrast for precisely the look you want. · The included diffusion filter has magnetized mounts at each corner. It can be easily placed on the fixture by simply positioning it with the magnets oriented down towards the four metal mounts on the fixture. The magnets hold it securely in place.
STORING THE LIGHT · When you're finished using the light, push the power switch to the Off position. Remove the power cord from the fixture by pressing the release button on the top of the connector and pulling the cord out of the fixture. Allow a few minutes for the fixture to cool down and then close the barndoors to protect the fixture during transport and storage. Always keep the barndoors closed when the light is not in use.
PRODUCT SPECIFICATIONS SP-S-1000B (Bi-Color) SPECIFICATIONS LED Count: 1012 LED Count: 1012 Color Temperature: 3200°K to 5600°K Color Temperature: 5600°K Dimming: 100% to 10% Dimming: 100% to 0% Watts: 60 Watts: 60 Lux: 6600 Lux @ 1m Lux: 6600 Lux @ 1m Coverage: 60° Coverage: 60° CRI: >93 CRI: >93 Bulb Life: 50,000 hours Bulb Life: 50,000 hours Weight: 8.3 lbs. (3.76 kg) Weight: 8.3 lbs. (3.76 kg) Dimensions: (H×W×L) 13.58 × 13.58 × 2.75˝ Dimensions: (H×W×L) 13.58 × 13.58 × 2.
SP-S-500D (Daylight) LED Count: 500 LED Count: 500 Color Temperature: 3200°K to 5600°K Color Temperature: 5600°K Dimming: 100% to 10% Dimming: 100% to 0% Watts: 30 Watts: 30 Lux: 3400 Lux @ 1m Lux: 3400 Lux @ 1m Coverage: 60° Coverage: 60° CRI: >93 CRI: >93 Bulb Life: 50,000 hours Bulb Life: 50,000 hours Weight: 5.8 lbs. (2.63 kg) Weight: 5.8 lbs. (2.63 kg) Dimensions: (H×W×L) 7.48 × 13.58 × 2.75˝ Dimensions: (H×W×L) 7.48 × 13.58 × 2.
ONE-YEAR LIMITED WARRANTY Genaray provides a limited warranty to the original purchaser that this product is free from defects in materials and workmanshipunder normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. Genaray’s responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at Genaray’s discretion, of any product that fails during normal consumer use.
