User's Manual

Table 1. Recommended cable gauges for
dierent lengths of signal cable.
Analog Output 1 and 2
Analog balanced XLR connectors connect
the subwoofer to the monitors.
These analog outputs carry an unltered
copy of the inputs. The subwoofer/main
monitor crossover is adjusted in the GLM
software from 50 Hz to 100 Hz.
See chapter "Bass Management" for
details.
THRU AES/EBU
The THRU AES/EBU is a bit-to-bit copy of
the digital audio signal on the IN Digital.
This output can be used for digital sharing
of the audio between subwoofers in the
case where multiple subwoofers are used.
This output can also be used for distributing
a stereo digital audio signal to monitors,
creating a 2.1 digital audio stereo monitoring
system.
Subwoofer Connector
This Speakon connector is used for
linking the RAM-SW amplier unit and the
7382A subwoofer enclosure. There is a
corresponding connector on the reex port
end of the enclosure.
A 10 m (33.3 ft) cable is provided with the
subwoofer. See Table 1 for recommended
minimum gauges for different lengths of
cable. Four pole cable is recommended. The
cable connectors are connected pin to pin,
with 1+ and 2+ in parallel, same as 1- and 2-.
GLM Management Network
All controls and calibration features included
in the 7382A SAM subwoofer are set using
the Genelec Loudspeaker Manager (GLM)
software. Two GLM Network connectors are
provided on the amplier for computer control.
These accept CAT5 or higher cable (RJ45
connector). Standard CAT cables can be used.
The GLM management network runs a
proprietary protocol. This is not an Ethernet
connection, do not connect to an Ethernet
network.
LED Connector
This connector allows linking a remote status
indicating light if the amplier unit is placed
so that its front panel light can not be seen.
Mains Power Input
The main power connection supports a wide
mains voltage range (100-240 VAC, 50-60
Hz). This enables the RAM-SW amplier to
be plugged in anywhere globally. When the
mains power is provided with a generator,
inverter, or certain lower-quality UPS
devices, we recommend ltering power to
remove harmonics and ensuring the voltage
supply is stable.
Figure 1. Connector panel of the RAM-SW amplier unit.
Cable Gauge Max. Length
4 x 2.0 mm
2
(14 AWG) 30 m / 100 ft
4 x 2.5 mm
2
(13 AWG) 40 m / 130 ft
4 x 3.3 mm
2
(12 AWG) 50 m / 165 ft
4 x 4.0 mm
2
(11 AWG) 60 m / 200 ft
SUBWOOFER
CONNECTOR
CONNECT ONLYTO GENELEC NETWORK
CONTROL NETWORK
MAINS INPUT
50 /60Hz1100 W
100 - 120 V~
220 - 230 V~
LFE IN
IN THRU
SERIAL NUMBER
RAM-SW AMPLIFIER
MODULE
www.genelec.com
MADE IN FINLAND
LED CONNECTOR
This device complies
with FCC Part 15 and
Canadian ICES-003
radio frequency Class
A emission
requirements. Refer
to operating manual
for full information.
213
OUT/THRU
IN
1
1
23
3
2
-
GND
+
IN 1
OUT 1
IN 2
OUT 2
ELECTRIC SHOCK HAZARD.DO NOT OPEN.DO NOT
SUBJECT TO WATER ORMOISTURE. NO USER SERVICEABLE
PARTSINSIDE. REFER SERVICING TO QUALIFIED
PERSONNEL. USE EARTHED MAINSCONNECTION ONLY.
WARNING
RISQUE DE CHOC ÉLECTRIQUE. NEPA S OUVRIR. NEPA S
EXPOSERÀL'EAU OU L'HUMIDITÉ. AUCUN COMPOSANT À
L'INTÉRIEUR REMPLAÇABLE PARL'UTILISATEUR. ADRESSER
TOUTE RÉPARATIONÀUN PERSONNELQUALIFIÉ. CET
APPAREILDOIT ÊTRE RACCORDÉÀLATERRE.
AVERTISSEMENT
LAITEONLIITETTÄVÄSUOJAKOSKETTIMILLAVARUSTETTUUN
PISTORASIAAN. APPARATET MÅTILKOPLESJORDET
STIKKONTAKT. APPARATEN SKALLANSLUTAS TILL JORDAT
UTTAG.
THISAMPLIFIER HAS BEEN CALIBRATED FOR USE WITHTHE
LOUDSPEAKER MARKED WITH THE SAMESERIAL NUMBER.
DO NOT MIXTHE CALIBRATED AMPLIFIER/LOUDSPEAKER
PAIRS!TURN OFFPOWER BEFORE DISCONNECTING
LOUDSPEAKER CONNECTIONS!
NOTE !
DIGITA L AES/EBU
ANALOG
ANALOG LFE
CHANNEL
INPUT
ANALOG SIGNAL INPUTS
AND OUTPUTS 1 AND 2
DIGITAL AES/EBU
IN AND THRU
CONNECTORS
GLM CONTROL
NETWORK
CONNECTORS
REMOTE LED
CONNECTOR
SUBWOOFER
CONNECTOR
MAINS
CONNECTOR
Figure 2. GLM Network cabling. Audio cabling not shown.
LISTENING
POSITION
MICROPHONE
GLM
NETWORK
GLM
NETWORK
GLM
NETWORK
USB
RAM-SW
RAM-XL
RAM-XL