User's Manual
3
power is provided with a generator, inverter or certain lower-
quality UPS devices, we recommend filtering of the mains
power voltage harmonics and taking care that the voltage
supply is stable.
The ANALOG IN connector is used for analog audio signals. The
maximum input level is +25 dBu. These monitors produce 100
dB SPL sound level at 1 meter in free space for an analogue
input signal of -6 dBu.
The DIGITAL IN AES/EBU female XLR connector is for AES/
EBU formatted digital audio input signals. This input is selected
automatically when a valid digital audio signal is present.
Analog input is selected when the AES/EBU signal input is
disconnected. The AES/EBU input supports two channels in a
single cable). When the digital source device controls the digital
output level, it may be advantageous to lower the level on the
monitor’s controls, which will enable the use of a higher digital
signal level with more digital resolution. With digital inputs the
audio is referenced to 0 dBFS (dB relative to the digital full scale,
the largest level that can be represented in the AES/EBU signal).
These monitors produce 100 dB SPL sound level at 1 meter in
free space for a digital input signal of –30 dBFS. The DIGITAL
OUT male XLR carries an unaltered copy of the digital signal fed
into the digital in connector. This enables daisy-chaining up to
four monitors.
The CONTROL NETWORK RJ-45 connectors are used with
Genelec Loudspeaker Manager™ (GLM™) network. These
connectors are not Ethernet LAN compatible. Do not connect
to Ethernet LAN.
Stand-Alone Control Functions
Bass Roll-Off Control
Bass Roll-Off control attenuates the monitor’s output near the
cut-off frequency. Attenuation levels of -2 dB, -4 dB or -6 dB
(both switches ON) can be selected.
Desktop 160 Hz
The desktop low frequency control (switch 5) attenuates the
bass frequencies around 160 Hz by 4 dB. This feature is de-
signed to compensate for the boost often occurring at this fre-
quency range when the monitor is placed upon a meter bridge,
table or similar reflective surface.
Bass Tilt Control
The Bass Tilt control switches (swiches 3 and 4) offer three at-
tenuation levels for the bass response below 800 Hz, usually
Figure 2. Connectors and controls on the back panel of a 8350A.
ANALOG
IN
DIGITAL THRU
AES/EBU
DIGITALIN
AES/EBU
MADE IN FINLAND
8350A
MAGNETICALLY SHIELDED
SERIAL NUMBER
www.genelec.com
GLM
NETWORK
MAINS INPUT
50/60Hz 200 W
100-240 V~
292-8350T-6
This devicecomplies
with FCCPart15and
Canadian ICES-003
radio frequency
ClassBemission
requirements. Refer
to operatingmanual
forfullinformation.
BASS ROLL-OFF
LEDDISAB LE
BASS TILT
A
-20dB
B
-2
-4
-2
-4
ON
OFF
STORED
(dB)
-10dB
RESET TO FACTORY
SETTINGS: PUSH
BUTTON FOR 10 SEC
LEVEL
DIGITAL
TREBLETI LT
+2
-4
DESKTOP160 Hz -4
(dB)
20 160
+2
-2
-4
dB
-6
0
4k 20k
BASS
TILT
800
BASS
ROLL-OFF
DESKTOP
ALL OFF
TREBLE
TILT
Frequency (Hz)
INPUT dBu
PRODUCING
100 dB SPL (1 m)
ISS
-2
+4
+2
-4
-6
+6
dBu
0
ON
OFF
SMART ACTIVE MONITO R
DIP SWITCHES FOR
STAND-ALONE USE
ROTARY
LEVEL
CONTROL
POWER
SWITCH
AUDIO SIGNAL
CONNECTORS:
-DIGITAL IN
-DIGITAL THRU
-ANALOG IN
MAINS INPUT
GLM NETWORK
CONNECTORS
Monitor
Mounting Position
Treble
Tilt
Bass
Tilt
Bass
Roll-Off
Desktop
Flat anechoic
response
None None None None
Free standing in
a damped room
None -2 dB None None
Free standing in
a reverberant room
None -4 dB None None
Near field on
a reflective surface
None -2 dB None -4 dB
In a corner None -4 dB -4 dB None
Table 1. Suggested Tone Control settings for some typical moni-
tor placement positions.