Instruction Manual Nexus Remote Monitor www.generac.
Table of Contents TABLE OF CONTENTS SAFETY........................................................... Inside Front Cover Read This Manual Thoroughly ........................................... 1 Safety Rules ..................................................................... 1 Operation and Maintenance ............................................... 2 How to Obtain Service ...................................................... 3 INTRODUCTION ...............................................................
Safety Rules THESE INSTRUCTIONS – This manual is in addition to the Owner's Manual for the generator. All nSAVE warnings and recommendations in the manufacturer's manuals bust be strictly adhered to for safe use. THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe operation be copied and nSAVE posted in potential hazard areas. Safety should be stressed to all operators, potential operators, and service and repair technicians for this equipment.
Safety Rules GENERAL HAZARDS • For safety reasons, the manufacturer recommends that the installation, initial start-up and maintenance of this equipment is carried out by a Dealer. • The engine exhaust fumes contain carbon monoxide, which can be DEADLY. This dangerous gas, if breathed in sufficient concentrations, can cause unconsciousness or even death. Do NOT alter or add to the exhaust system or do anything that might render the system unsafe or in noncompliance with applicable codes and standards.
Wireless Display System It is the operator's responsibility to perform all safety checks, to make sure that all maintenance for safe operation is performed promptly, and to have the equipment checked periodically by an Authorized Service Dealer. Normal maintenance service and replacement of parts are the responsibility of the owner/operator and, as such, are not considered defects in materials or workmanship within the terms of the warranty.
Wireless Display System PAIR/RESET BUTTON Figure 2 — Remove Cover Plate & Rubber Gasket The display unit has a Pair/Reset button on the bottom of the enclosure (Figure 11). The Pair/Reset button has three functions. • It is used to pair the display unit with the generator transceiver during installation. See the installation section for complete instructions. • It will silence the internal buzzer when briefly pressed and released.
Wireless Display System Figure 4 – Unplug the existing 4-pin plug Figure 6 – Plug in the 5-pin plug 11. Re-route the 4-pin plug just disconnected to the generator transceiver. Cut the wire harness tie wraps if necessary. NOTE: • Route the 4-pin end of the cable back to the LED board and plug it into the 4-pin header on the LED board. (Refer back to Figure 4.) DO NOT force the plug into the header. Gently insert the plug until it locks into place. 14.
Wireless Display System DISPLAY UNIT STARTUP The Display unit and the generator transceiver are “Paired” at the factory during final test and should start communicating as soon as they are both powered up. If, however, pairing is required (when replacing a module, adding a second display unit, etc.), follow the “Pairing the Generator Transceiver with the Display Unit” procedure. Figure 10 – Place the Display Unit Against the Generator Transceiver 16.
Wireless Display System 27. Proceed with the “Re-Assemble the Generator” section 28. If the two modules fail to pair up within 30 seconds, the yellow LED will stop flashing and the red LED will begin to flash. 29. The flashing red LED indicates the pairing process has failed. If this happens proceed as follows: • Press and release the Pair/Reset button to stop the red LED from flashing.
Wireless Display System RESETTING THE SYSTEM 3. The Nexus Remote Monitor system can be reset, and all existing pairing information deleted, as follows: 4. RESETTING THE DISPLAY UNIT 5. Press and hold the Pair/Reset button on the bottom of the display unit for a minimum of 10 seconds. Cut the tie wrap holding the 4-wire LED wire harness to the enclosure (Figure 2, "A"). Carefully cut and remove the tape from the main wire harness. (Figure 2, "B").
Final Assembly Decal Drawing Drawing 0H9609 ITEM 1 2 3 4 5 6 7 8 9 10 11 PART NO. 0G7127 0H9607 0G7161 0H8075 0H9593 0H9608 0G7130 OG7092 084543A 052777 0H8352 QTY. 1 1 2 1 1 1 2 1 2 2 1 DESCRIPTION CARTON 306 X 227 X 80 PE FOAM BATTERY, AAA BASIC WIRELESS 2010H GENERATOR SIDE RF ANNUNCIATOR MANUAL STATIC SHIELDING BAG, 200 X 140 X 0.08mm GASKET, 2.0 X 4.
Warranty GENERAC POWER SYSTEMS “180 DAY” LIMITED WARRANTY FOR WIRELESS REMOTE MONITOR (for AIR-COOLED GENERATORS) For a period of 180 days from the date of original sale, Generac Power Systems, Inc. (Generac) warrants its wireless remote monitor will be free from defects in materials and workmanship for the items and period set forth below.