Product Manual

ManualsBrandsGenerac ManualsElectricalHomeLink Upgradeable 30 Amp Manual Transfer Switch

SAVE THIS MANUAL FOR FUTURE REFERENCE

Owner's and Installation Manual

For

Manual Transfer Switch



NOT INTENDED FOR USE IN CRITICAL LIFE SUPPORT

APPLICATIONS.



THIS PRODUCT CAN BE INSTALLED BY

THE HOMEOWNER. HOWEVER, IF YOU ARE

UNCOMFORTABLE WITH THE SKILLS OR TOOLS

REQUIRED, HAVE A QUALIFIED ELECTRICIAN OR

CONTRACTOR PERFORM THE INSTALLATION.



INDOOR INSTALLATION ONLY!

Para español , visita: http://www.generac.com/service-support/product-support-lookup

Pour le français, visiter : http://www.generac.com/service-support/product-support-lookup

WWW.GENERAC.COM

888-436-3722

MODEL NUMBER: _________________________

SERIAL NUMBER: _________________________

DATE PURCHASED:________________________

Models:

006852 Switch and Cord

006853 Switch, Cord and Resin Power Inlet Box

006854 Switch, Cord and Aluminum Power Inlet Box

Summary of content (12 pages)

PAGE 1
Owner's and Installation Manual For Manual Transfer Switch Models: 006852 Switch and Cord 006853 Switch, Cord and Resin Power Inlet Box 006854 Switch, Cord and Aluminum Power Inlet Box MODEL NUMBER: _________________________ SERIAL NUMBER: _________________________ DATE PURCHASED:________________________ WWW.GENERAC.COM 888-436-3722 Para español , visita: http://www.generac.com/service-support/product-support-lookup Pour le français, visiter : http://www.generac.
PAGE 2
Table of Contents Safety Rules........................................................Inside Front Cover General Information.........................................................................2 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Introduction...........................................................................................2 Unpacking............................................................................................2 Equipment Description...................................................
PAGE 3
Safety Rules WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. (000002) CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. (000003) NOTE: After this heading, read instructions that, if not strictly complied with, may result in damage to equipment and/or property. These safety warnings cannot eliminate the hazards that they indicate.
PAGE 4
General Information 1.1 INTRODUCTION Figure 1.1 — Panelboard This manual has been prepared especially for the purpose of familiarizing personnel with the design, application, installation, operation and servicing of the applicable equipment. Read the manual carefully and comply with all instructions. This will help to prevent accidents or damage to equipment that might otherwise be caused by carelessness, incorrect application, or improper procedures.
PAGE 5
Installation 1.8 SAFE USE OF TRANSFER SWITCH Figure 2.1 — Mount Transfer Switch Before installing, operating or servicing this equipment, read the SAFETY RULES (inside front cover) carefully. Comply strictly with all SAFETY RULES to prevent accidents and/or damage to the equipment. The manufacturer recommends that a copy of the SAFETY RULES are posted near the transfer switch. Also, be sure to read all instructions and information found on tags, labels and decals affixed to the equipment.
PAGE 6
Installation Figure 2.2 — Typical 3-Pole Transfer Mechanism Note: The power inlet box, if not supplied in this kit, is available through Generac. You may wish to purchase special Generac cable through your dealer with control cables for easier standby generator installation/upgrades in the future. A Conductors must be properly supported, of approved insulative qualities, protected by approved conduit, and of the correct wire gauge size in accordance with applicable codes.
PAGE 7
Installation 2.6 CIRCUIT BREAKER WIRING A manual handle is shipped with the transfer switch. Manual operation must be checked before the transfer switch is operated electrically. To check manual operation, proceed as follows: NOTE: Balance must be maintained when moving circuit locations from main electrical distribution panel to optional standby load center. Circuit breaker positions alternate buss bars vertically.
PAGE 8
Operation Figure 3.1 — Actuating Transfer Switch DANGER LOAD CONNECTED TO STANDBY POWER SOURCE LOAD CONNECTED TO UTILITY POWER SOURCE TRANSFER SWITCH OPERATING LEVER MANUAL TRANSFER HANDLE Indicates a hazardous situation which, if not avoided, will Proceed with caution. Generator output voltage result death or serious injury.to transfer switch + is in now being delivered terminals. Contact with live terminals results in extremely dangerous and possibly fatal (000001) electrical shock. 7.
PAGE 9
Operation 3. 4. 5. 6. 7. connected to the main harness of the transfer switch. Install the front cover of the transfer switch with four (4) screws provided. See Figure 3.2. Turn ON the utility power supply to the transfer switch, using the means provided (such as utility main line circuit breaker). The Utility Light will illuminate only if the transfer switch is in the Generator position, and utility voltage is present.
PAGE 10
8 375mm [14.7"] 279mm [11.0"] 366mm [14.4"] R7mm [R0.3"] 4.42mm [0.2"] 292mm [11.5"] 400.6mm [15.8"] 7.08mm [0.3"] R4mm [R0.2"] 392mm [15.4"] 13mm [0.5"] 13mm [0.5"] 528.17mm [51.1"] KNOCKOUT SUITABLE FOR 3/4" & 1" CONDUIT SIZE (IF 2 FT WHIP NOT INCLUDED) 96mm [3.8"] 4mm [0.2"] Installation Diagram Installation Drawing No.
PAGE 11
REVISION: -ADATE: 9/12/14 * NOTE: WHEN UTILIZED IN THIS APPLICATION A GROUNDING ELECTRODE MAY BE REQUIRED BY LOCAL CODE TO BE CONNECTED TO THE GENERATOR. 50A 2-POLE CIRCUIT BREAKER NOTE: NEUTRAL CONDUCTOR AND GROUND SHOULD BE BONDED AT PORTABLE GENERATOR. SEE GENERATOR MANUAL FOR DETAILS.
PAGE 12
Part No. 0K9960 Rev. A 01/09/15 Printed in USA ©2015 Generac Power Systems, Inc. All rights reserved Specifications are subject to change without notice. No reproduction allowed in any form without prior written consent from Generac Power Systems, Inc. Generac Power Systems, Inc. S45 W29290 Hwy. 59 Waukesha, WI 53189 1-888-GENERAC (1-888-436-3722) generac.