Mobile Link® Wi-Fi/Ethernet Remote Monitoring Installation and User Manual TM Mobile Link Customer Support http://support.mobilelinkgen.com US: 1-855-436-8439 Canada: 1-844-843-9436 Para español , visita: http://www.generac.com/service-support/product-support-lookup Pour le français, visiter : http://www.generac.
Generator Model: Generator Serial Number: Mobile Link Serial Number: Date Purchased: Record the information found on the unit data label on this page. Always supply the complete model and serial numbers of the unit when contacting an Independent Authorized Service Dealer (IASD) about parts and service. Operation and Maintenance: Correct maintenance and care of the unit ensures a minimum number of problems, and keeps operating expenses at a minimum.
Table of Contents Section 1: Safety Rules Section 5: Registration Introduction ..................................... 1 Antenna Statement .............................1 Read This Manual Thoroughly ............1 Safety Rules.................................... General Safety ................................ General Safety Hazards.................. Electrical Hazards ........................... Explosion Hazards ..........................
Safety Rules Section 1: Safety Rules Introduction Thank you for purchasing this home standby generator product accessory. NOTE: This device complies with Part 15 of the FCC Rules (and with Industry Canada license-exempt RSS standard(s)). Operation is subject to the following two conditions: • this device may not cause harmful interference, and • this device must accept any interference received, including interference that may cause undesired operation.
Safety Rules General Safety WARNING Consult Manual. Read and understand manual completely before using product. Failure to completely understand manual and product could result in death or serious injury. (000100a) General Safety Hazards DANGER Electrocution. High voltage is present at transfer switch and terminals. Contact with live terminals will result in death or serious injury. (000129) WARNING Accidental Start-up.
Safety Rules locked before operating the generator. If work must be done around an operating unit, stand on an insulated, dry surface to reduce potential shock hazard. Explosion Hazards DANGER Explosion and fire. Fuel and vapors are extremely flammable and explosive. No leakage of fuel is permitted. Keep fire and spark away. Failure to do so will result in death or serious injury. (000192) DANGER Explosion and Fire. Fuel and vapors are extremely flammable and explosive.
General Information and Setup Section 2: General Information and Setup Introduction This section of the manual describes the features and controls of the Mobile Link Wi-Fi/ Ethernet remote monitoring system. Ever y effort was made to ensure that the information and instructions in this manual were both accurate and current at the time the manual was written. However, the manufacturer reserves the right to change, alter, or otherwise improve this product or manual at any time without prior notice.
General Information and Setup A 009154 Figure 2-1. Mobile Link Information Screen A 002726b Figure 2-2.
General Information and Setup Setup • If the Wi-Fi signal is weak and the network Before installing the Mobile Link device, perform the Pre-Installation Signal Strength Test to determine if the existing Wi-Fi signal is sufficient for use or if it must be boosted. Pre-Installation Signal Strength Test NOTE: Most network routers automatically broadcast their Wi-Fi network name every few seconds. Network owners may choose to disable broadcasting, making the home network invisible. 1. See Figure 2-3.
Getting Connected Section 3: Getting Connected Connecting to Wi-Fi Networks Connecting to New Wi-Fi Network 1. Install the Mobile Link Wi-Fi/Ethernet accessory. 2. The Mobile Link Wi-Fi/Ethernet accessory will be immediately ready to connect after the accessory is powered on. 3. Download “Mobile Link Setup” App on Google Play or Apple Apps Store, if not already installed. 4. Open “Mobile Link Setup” App and follow guided instructions provided in the app.
Installation and Operation Section 4: Installation and Operation Mobile Link Kit Numbers 2. See Figure 4-2. Use arrow keys to toggle between “Yes” and “No.” Select “No” and press ENTER. Part No. Description G007170-0 Mobile Link Wi-Fi/Ethernet Device - Enable Wi-Fi? Yes + Installation NOTE: Verify correct generator operation and performance before adding a Mobile Link WiFi/Ethernet device during a new generator installation. 009010 Disabling On-Board Wi-Fi Figure 4-2.
Installation and Operation Preparing Generator (New Installations) DANGER Electrocution. Do not wear jewelry while working on this equipment. Doing so will result in death or serious injury. (000188) 1. Unlock both locks, open generator lid, and remove front panel. 2. See Figure 4-4. If generator is equipped with an internal breaker near the controller, remove end panel from right side. Otherwise, proceed to Step 3. 002729 002727 Figure 4-4. Removing End Panel (Internal Breaker) 3. Turn generator OFF.
Installation and Operation Preparing Generator (Equipped with Existing Mobile Link Unit) DANGER Electrocution. Do not wear jewelry while working on this equipment. Doing so will result in death or serious injury. (000188) Connecting New Mobile Link Unit 1. See Figure 4-7. Push the threaded end of the Mobile Link Wi-Fi/Ethernet device (A) from the controller end panel from the inside. Only the threads should show from the outside of the enclosure. A 1.
Installation and Operation 5. See Figure 4-8. With connector installed, tighten plastic fitting to secure Wi-Fi/Ethernet unit until tight and device is secured to end panel. • Align antenna vertically. 002733 Figure 4-9. Accessory Port (Internal Breaker) NOTE: If there is a decal labeled “Port 1” or “Accessory Prt 1,” remove decal to locate port. 8. Install eight pin connector harness into open socket on controller. NOTE: The connector will only fit one way. DO NOT force. CAUTION Equipment damage.
Installation and Operation Complete Unit Installation (New and Retrofit) 1. Install end panel, controller, or sheet metal controller cover. Install and tighten retaining fasteners. 2. Verify generator is OFF. 3. Install generator controller fuse. 4. Install T1 fuse into transfer switch using an appropriate fuse puller. 5. Turn main breaker in the home electrical panel to ON. On generator control panel, follow installation wizard and validate correct date, time, etc. 6. Place generator in AUTO.
Registration Section 5: Registration Once the Mobile Link Wi-Fi/Ethernet device has been installed, it should be registered and activated to obtain full benefits of product capabilities. Gather the following information prior to initiating registration process: • E-mail address • Mobile Link Serial Number located on label on back of unit. A second label on packaging also includes the serial number. • Generator serial number located on label plate, near control panel console.
Mobile Link Cellular App Section 6: Mobile Link Cellular App Download the Mobile Link Cellular for Generators app: Mobile Link Setup App “Mobile Link Setup” app guides users through the wireless connection process, allowing the generator to communication with the home Wi-Fi network. NOTE: For additional connection assistance, or for inquires about a Mobile Link DealerManaged plan, contact an IASD. After Connection See Figure 6-1.
Mobile Link Cellular App This page intentionally left blank.
Part No. A0000349354 Rev. A 02/19/2020 ©2020 Generac Power Systems, Inc. All rights reserved Specifications are subject to change without notice. No reproduction allowed in any form without prior written consent from Generac Power Systems, Inc. Generac Power Systems, Inc. S45 W29290 Hwy. 59 Waukesha, WI 53189 1-888-GENERAC (1-888-436-3722) www.generac.
