Specification Sheet
6 of 6
®
Model # Product Description
G005819-0 26R Wet Cell Battery
Every standby generator requires a battery to start the system. Generac offers the recommended 26R wet cell bat-
tery for use with all air-cooled standby product (excluding PowerPact
®
).
G007101-0 Battery Pad Warmer
The pad warmer rests under the battery. Recommended for use if the temperature regularly falls below 0 °F (-18
°C). (Not necessary for use with AGM-style batteries)
.
G007102-0 Oil Warmer
Oil warmer slips directly over the oil filter. Recommended for use if the temperature regularly falls below 0 °F (-18 °C).
G007103-1 Breather Warmer
The breather warmer is for use in extreme cold weather applications. For use with Evolution controllers only in
climates where heavy icing occurs.
G005621-0
Auxiliary Transfer Switch
Contact Kit
The auxiliary transfer switch contact kit allows the transfer switch to lock out a single large electrical load you may
not need. Not compatible with 50 amp pre-wired switches.
G007027-0 - Bisque Fascia Base Wrap Kit
The fascia base wrap snaps together around the bottom of the new air cooled generators. This offers a sleek, con-
toured appearance as well as offering protection from rodents and insects by covering the lifting holes located in
the base.
G005703-0 - Bisque Touch-Up Paint Kit
If the generator enclosure is scratched or damaged, it is important to touch up the paint to protect from future
corrosion. The touch-up paint kit includes the necessary paint to correctly maintain or touch up a generator en-
closure.
G006482-0 – 10 kW
G007216-0 – 14 / 18 kW
Scheduled Maintenance Kit
Generac's scheduled maintenance kits provide all the items necessary to perform complete routine maintenance
on a Generac automatic standby generator (oil not included).
G007005-0 Wi-Fi LP Fuel Level Monitor
The Wi-Fi enabled LP fuel level monitor provides constant monitoring of the connected LP fuel tank. Monitoring
the LP tank's fuel level is an important step in verifying the generator is ready to run during an unexpected power
failure. Status alerts are available through a free application to notify users when the LP tank is in need of a refill.
G007000-0 (50 amps)
G007006-0 (100 amps)
Smart Management Module
Smart Management Modules (SMM) are used to optimize the performance of a standby generator. It manages
large electrical loads upon startup and sheds them to aid in recovery when overloaded. In many cases, using
SMM’s can reduce the overall size and cost of the system.
G007169-0 (4G LTE)
G007170-0 (Wi-Fi/Ether-
net)
Mobile Link
®
Cellular
Accessories
The Mobile Link family of Cellular Accessories allow users to monitor the status of the generator from anywhere
in the world, using a smartphone, tablet, or PC. Easily access information such as the current operating status and
maintenance alerts. Users can connect an account with an authorized service dealer for fast, friendly, and proac-
tive service. With Mobile Link, users are taken care of before the next power outage.
Dimensions & UPCs
Dimensions shown are approximate. See installation manual for exact dimensions. DO NOT USE THESE DIMENSIONS FOR INSTALLATION PURPOSES.
648 mm
[25.5 in]
727.2 mm
[28.6 in]
637.6 mm
[25.1 in]
1232 mm
[48.5 in
]
1218 mm
[48.0 in]
LEFT SIDE VIEW
FRONT VIEW
Model UPC
G007171-0 696471074680
G007172-0 696471074673
G007223-0 696471082548
G007224-0 696471082555
G007225-0 696471082562
G007226-0 696471082579
G007228-0 696471082586
10/14/18 kW
Generac Power Systems, Inc. • S45 W29290 HWY. 59, Waukesha, WI 53189 • generac.com
©2020 Generac Power Systems, Inc. All rights reserved. All specifications are subject to change without notice. Part No. A0000973374 Rev. A 10/22/2020
®
Available Accessories10/14/18 kW