Full Product Manual

ManualsBrandsGeneral International ManualsDust Collectors & Air Filtration5 HP 3800 CFM 2-Stage Dust Collector

SETUP & OPERATION MANUAL

2 STAGE DUST COLLECTOR

Heavy-duty construction.

Simple design with easy set-up and mainte-

nance.

High quality motor designed speciﬁcally for

heavy-duty use and long service life.

Cast steel, high efﬁciency fan for superior perfor-

mance and low noise level.

Equipped with two ultra efﬁcient 1 micron can-

ister ﬁlters to reduce airborne dust and offers

ﬁltering capacity 6 times more than traditional

ﬁlter bags.

Canister ﬁlter equipped with crank handle/

internal shaker for easy ﬁlter cleaning without

removing bag.

2 piece caster mounted 45 gallon (55 U.S. gallon)

drum included (item #10-820B).

FEATURES

• Airﬂow capacity

3800 cfm (10-850CF) / 4955 cfm (10-875CF)

• Air speed

48 m/sec (10-850CF) / 45 m/sec (10-875CF)

• Sound rating

85-90 dB (10-850CF) / 90-95 dB (10-875CF)

• Inlet Diameter (1)

(1) 9” (229 mm) (ou 4) 5” (127 mm) (10-850CF)

(1) 10” (254 mm) (ou 4) 5” (127 mm) (10-875CF)

• Static Pressure

15 5/8” of water (10-850CF) / 16 1/2” (10-875CF)

• Canister Filters (Dia. x H)

20” x 44” x 2 pcs (510 x 1120 mm x 2 pcs)

• Motor

M1 5 HP, 220 V, 1 Ph, 21 A (10-850CF)

M2 5 HP, 220 V, 3 Ph, 13.7 A (10-850CF)

M2 7 1/2 HP, 220 V, 3 Ph, 21.5 A (10-875CF)

M3 5 HP, 600 V, 3 Ph, 4.9 A (10-850CF)

M3 7 1/2 HP, 600 V, 3 Ph, 6.9 A (10-875CF)

• Overall dimensions (L X W X H)

63” x 51” x 90 1/2”

(1600 x 1300 x 2300 mm) (10-850CF)

69” x 59” x 110”

(1750 x 1500 x 2800 mm) (10-875CF)

• Weight

418 LBS (190 kg) with ﬁlters (10-850CF)

462 LBS (210 kg) with ﬁlters (10-875CF)

SPECIFICATIONS

MODEL

#10-850CF

#10-875CF

10-850CF

10-875CF

10-850CF Version 2/Revision 1 - June 2014 (S/N 14559311)

10-875CF Version 2/Revision 1 - June 2014 (S/N 14697012)

Summary of content (19 pages)

PAGE 1
SETUP & OPERATION MANUAL FEATURES 2 STAGE DUST COLLECTOR Heavy-duty construction. Simple design with easy set-up and maintenance. High quality motor designed speciﬁcally for heavy-duty use and long service life. Cast steel, high efﬁciency fan for superior performance and low noise level. Equipped with two ultra efﬁcient 1 micron canister ﬁlters to reduce airborne dust and offers ﬁltering capacity 6 times more than traditional ﬁlter bags.
PAGE 2
1. General safety rules "WARNING炰When using electric tools basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following. Read all these instructions before attempting to operate this product and save these instructions". 1- Keep work area clear 2- Consider work area environment - Do not expose tools to rain. - Do not use tools in damp or wet locations. - Keep work area well lit.
PAGE 3
15- Stay alert - Watch what you are joining, use common sense and do not operate the tool when you are tired. 16- Check damaged parts - Before further use of tool, it should be carefully checked to determine that it will operate properly and perform its intended function. - Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation.
PAGE 4
<4> Contact local agent for any problem of assembly and missing part. Warning! Do not connect the dust collector to the power source until machine is completely assembled and you have read and understand the entire instruction manual. 4. Handling and transportation The net weight of this machine is about 270 kgs. We recommend to move and assemble it with forklift truck. 5. Electrical connection / disconnection <1> Electrical connection: a.
PAGE 5
7. Assembly drawing & instructions Remove the dust collector components from the shipping containers. Please check parts list for missing or damaged parts. 10-850CFM PARTS LIST 1. CARTRIDGE FILTER 2 pieces 2. DRUM 3. Ø 8” FLEXIBLE HOSE 1 piece 2 pieces 4. Ø 7” FLEXIBLE HOSE 5. COVER 6. 9” HOSE CLAMP 1 piece 1 piece 2 pieces 7. HOSE CLAMP 8. HANGER (R & L) 9. HANGER (S) 4 pieces 2 pieces 2 pieces 10. CYCLONE SEPARATOR 11. AIR FLOW PIPE 12. BLOWER & SWITCH 13.
PAGE 6
10-875CFM PARTS LIST 1. CARTRIDGE FILTER 2 pieces 2. Ø 8” FLEXIBLE HOSE 3. Ø 8” HOSE CLAMP 4. Ø 7” HOSE CLAMP 5. DRUM COVER 2 pieces 4 pieces 4 pieces 2 pieces 6. HANGER (S) 7. HANGER (R & L) 8. MANIFOLD 2 pieces 2 pieces 1 piece 9. Ø 7” FLEXIBLE HOSE 10. Ø 8” X 2 OUTLET 2 pieces 1 piece 11. AIR FLOW PIPE 12. CYCLONE SEPARATOR 13. BLOWER & SWITCH 14. UPPER LEG 1 piece 1 piece 1 piece 4 pieces 15. DRUM 1 piece 16. BAG CLAMP 17. PLASTIC BAG 18. HARDWARE PACKAGE 19. Ø 5" X 4 INLET 20.
PAGE 7
1. Fasten air flow pipe to blower housing with four 5/16” flat washer and four 5/16” x 3/4 inch-long screws. (10-850CFM) Fasten air flow pipe to blower housing with four 3/8” flat washer and four 3/8” x 3/4 inch-long screws. (10-875CFM) 4. Put the rubber gasket material around the outer edge of Cyclone separator and continue until a complete circle. Make sure the rubber gasket hole fit on flange hole. (10-850CFM &10-875CFM) 2.
PAGE 8
7. Assemble one leg section to blower housing and fasten with four 3/8" x 1 inch-long screw, four 3/8" flat washers. (10-850CFM) Assemble one leg section to blower housing and fasten with four 3/8" x 1 inch-long screw, four 3/8" flat washers. (10-875CFM) 8. Assemble remaining three legs to blower housing in the same manner. (10-850CFM & 10-875CFM) 9. Illustrates upper legs assembled to blower housing. (10-850CFM & 10-875CFM) 10. Place one support bracket on the inside of two upper legs.
PAGE 9
14. Attach the remaining brackets and lower legs to upper legs assemblies in the same manner. (10-850CFM & 10-875CFM) 17. Attach the L-type hanger (right) to the mounting holes on the blower housing, as shown, using two 5/16” x 1 inch long screws and two 5/16” flat washers. (10-850CFM) 15. Put the rubber gasket material around the outer edge of ø 8” outlet and continue until a complete oblong. Make sure the rubber gasket hole fit on flange hole. (10-850CFM & 10-875CFM) 16.
PAGE 10
20. Connect the two flexible hose 8” to the outlet / inlet port and secure in place with the 8” hose clamp as shown. (10-850CFM & 10-875CFM) 23. Position the 5 inch x 4 holes inlet housing to 9 inch inlet of blower housing. Align holes in inlet housing with pre-drilled holes in inlet and fasten with three pan head screws. (10-850CFM) 21. Connect the handle to the center of cartridge filter and secure in place with the 5/16"x3/4" HEX SCREW as shown. (10-850CFM & 10-875CFM) 22.
PAGE 11
26.Attach the casters to the bottom of the lower collection drum,using four 3/8”ǘ16 hex nuts,eight 3/8” flat washers, and four 3/8” lock washers. (10-850CFM & 10-875CFM) 27.Install the three drum latches,with six 10-24ǘ 3/8”Phillips head screws and six 10-24 hex nuts.use the remaining six 10-24ǘ3/8” Phillips head screws and six 10-24 hex nuts to plug the lower latch mounting holes. (10-850CFM & 10-875CFM) 29.Insert the rubber seal over the top lip of the drum rim.
PAGE 12
32.Before assembling the flexible hose ensure that the ȶ1” plugs are removed from the vacuum tube and drum 35. Using two ȶ1”×1700 ϩˣȶ 2” flexible hose and two ȶ 1”clamps and ȶ2”clamps connect the lower collection drum assemblies to the manifold. Assemble manifold on the one lower leg with two 3/8”ǘ 1inch-long screws,two 3/8” flat washer. (10-875CFM) 33.Assemble the 1”ǘ1700 ϩ flexible hose with the 1”clamps.(10-850CFM) Assemble the two 1”ǘ1700 ϩ flexible hose with the 1”clamps.(10-875CFM) 36.
PAGE 13
Identification: 10-850CFM 10-875CFM 13
PAGE 14
ASSEMBLY DRAWING 10-850CFM ξ൤ᐒఓϦљ 3122/17/41 рკക 14
PAGE 15
REPLACEMENT PARTS LIST 10-850CFM OP! 2! NPUPS! QBSU!OBNF! R(UZ! 2! OP! 56! VQQFS!MFH! 3! QPXFS!DPSE! 3! 57! MPXFS!MFH! 5! 4! 203#!IFY!OVU! 5! 58! 6027#y!2#!IFY!IE!TDSFX! 27! 5! 203#!GMBU!XBTIFS! 5! 59! 6027#!GMBU!XBTIFS! 43! 6! NPUPS!HBTLFU! 2! 5:! 6027#!MPDL!OVU! 27! 7! NPUPS!CBTF! 2! 61! PVUMFU! 2! 7B! 203#y2.
PAGE 16
OP! QBSU!OBNF! R(UZ! OP! QBSU!OBNF! R(UZ! 98! 6027#!IFY!OVU! 2! 216C! 205#!GMBU!XBTIFS! 27! 99! DPWFS!DMBNQ! 4! 217! TXJWFM!IBOEMF! 3! 9:! 4027#y!409#!SPVOE!IE!TDSFX! 7! 217B! 6027#y405#!IFY!TDSFX! 3! :1! 4027#!IFY!OVU! 7! 217C! 6027#!TQFDJBM!GMBU!XBTIFS! 3! :2! 4027#y!409#!SPVOE!IE!TDSFX! :3! 205#!IFY!OVU! 9! 9! 218! CFBSJOH! 218B! HSFBTF!TFBM! 3! 3! :4! 3#DBTUFS! 5! 218C! 205#y2#!IFY!IE!TDSFX! 9! :5! 409#!IFY!OVU! 5! 218D! 205#!GMBU!XBTIFS! 9! :6! 409#!MPDL!XBTIFS! 5! 219!
PAGE 17
ASSEMBLY DRAWING 10-875CFM ξ൤ᐒఓϦљ 3122/18/16 рკക 17
PAGE 18
REPLACEMENT PARTS LIST 10-875CFM OP! QBSU!OBNF! R(UZ! OP! QBSU!OBNF! R(UZ! 2! 3! NPUPS! QPXFS!DPSE! 2! 3! 42! 409#!IFY!OVU! 43! 409#yPE34y3u!GMBU!XBTIFS! 9! 9! 4! 203#!IFY!OVU! 5! 44! JOMFU!HBTLFU! 2! 5! 203#!GMBU!XBTIFS! 5! 45! JOMFU! 2! 5B! 203#!TQSJOH!XBTIFS! 5! 46! 409#yPE34y3u!GMBU!XBTIFS! 9! 6! NPUPS!HBTLFU! 2! 47! 409#y2#!IFY!TDSFX! 9! 7! 409#!TQSJOH!XBTIFS! 5! 48! 8#!IPTF!DMBNQ! 5! 8! 409#y2.
PAGE 19
OP! QBSU!OBNF! R(UZ! OP! QBSU!OBNF! R(UZ! 94! DBCMF!HMBOE! 95! 409#y2#!IFY!TDSFX! 96! 409#yPE34y3u!GMBU!XBTIFS! 4! 3! 3! 229! 409#!IFY!OVU! 22:! 409#!TQSJOH!XBTIFS! 231! 409#yPE34y3u!GMBU!XBTIFS! 9! 9! 27! 97! DPWFS!DMBNQ! 3! 3! 98! 99! 9:! :1! 2! 3! 3! 3! 232! BDSZMJD!! 233! SVCCFSU!IBOEMF! 234! 6027#y405#!IFY!TDSFX!! 235! 6027#ØPE29Ø3u!GMBU!XBTIFS!! 236! 6027#!IFY!OVU! 3! 5! 5! 5! :2! TVQQPSU!CSBDLFU!)T*! 3! 237! 203#!TQFDJBM!GMBU!XBTIFS! 5! :3! ȶ3#!IPTF!DMBNQ! 3! 238! 203#y2.