SETUP & OPERATION MANUAL 22" PRESS DRILL FEATURES Rotating, crank-operated worktable with quick release clamp. Large front mounted paddle style stop switch. Adjustable spindle tension return spring. Built-in lamp illuminates the drilling area (Bulb not included). Spindle is supported by high quality ball bearings. Cast-iron pulleys reduce vibration. Industrial 1 HP motor. Heavy-duty positive depth stop for quick adjustment. 3/4” drill chuck with key included.
GENERAL® INTERNATIONAL 8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Telephone (514) 326-1161 • Fax (514) 326-5555 • www.general.ca THANK YOU for choosing this General® International model 75-500 22” Drill Press. This press drill has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service.
GENERAL® INTERNATIONAL WARRANTY All component parts of General® International and Excalibur by General International® products are carefully inspected during all stages of production and each unit is thoroughly inspected upon completion of assembly.
TABLE OF CONTENTS Rules for safe operation...................................................................................................... 5 Electrical requirements....................................................................................................... 6 Identification of main parts and components................................................................... 7 Installation...............................................................................................................
RULES FOR SAFE OPERATION To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as potential hazards. General® International disclaims any real or implied warranty and holds itself harmless for any injury that may result from the improper use of it’s equipment. 1. Do not operate the drill press when tired, distracted, or under the effects of drugs, alcohol or any medication that impairs reflexes or alertness. 2.
ELECTRICAL REQUIREMENTS BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE WITH GREATER VOLTAGE THAN NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE TO THE MACHINE. IF IN DOUBT, CONTACT A QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER SOURCE. THIS TOOL IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS.
IDENTIFICATION OF MAIN PARTS AND COMPONENTS FRONT VIEW K G F H E I D C J B A A. BASE G. HEAD STOCK B. COLUMN H. MOTOR C. TABLE I. D. INTERLOCK CHUCK GUARD J. TABLE CRANK HANDLE E. CHUCK K. BELT/PULLEY COVER F.
INSTALLATION PLACEMENT WITHIN THE SHOP This machine should be installed and operated only on a solid, flat and stable floor that is able to support the weight of the sander (372 lbs - 169 kg) and the operator. Using the dimensions shown as a guideline, plan for pla-cement within your shop that will allow the operator to work unencumbered and unobstructed by foot traffic (either passing shop visitors or other shop workers) or other tools or machinery.
2. PLACE SAFETY GUARD PIVOT HOUSING ON THE BRACKET INSTALLING THE CHUCK GUARD ON THE HEADSTOCK vvv TO REDUCE THE RISK OF SERIOUS INJURY, ALWAYS COVER THE CHUCK AND DRILL BIT WITH THE CHUCK GUARD WHEN USING THE DRILL PRESS. NOTE: THE SEE-THROUGH SWING-AWAY CHUCK GUARD IS EQUIPPED WITH A SAFETY INTERLOCK THAT AUTOMATICALLY SHUTS OFF THE MACHINE WHEN THE CHUCK GUARD IS OPENED. TO TURN ON OR RUN THE DRILL PRESS, MAKE SURE THAT THE CHUCK OVE SCREWS FROM BRACKET GUARD IS PROPERLY CLOSED. A B A 3.
BASIC ADJUSTEMENTS & CONTROLS CONNECTING TO A POWER SOURCE TO REDUCE THE RISK OF SHOCK OR FIRE DO NOT OPERATE THE UNIT WITH A DAMAGED POWER CORD OR PLUG. REPLACE DAMAGED CORD OR PLUG IMMEDIATELY. SWITCH OFF TO AVOID UNEXPECTED OR UNINTENTIONAL START-UP, MAKE SURE THAT THE POWER SWITCH IS IN THE OFF POSITION BEFORE CONNECTING TO A POWER SOURCE. Once the assembly steps have been completed, uncoil the power cord and plug into an appropriate outlet.
ADJUSTING TABLE HEIGHT TO AVOID UNEXPECTED OR UNINTENTIONAL START-UP, MAKE SURE THAT THE POWER SWITCH IS IN THE “OFF”. 1. Loosen the column lock handle 1. 2. Turn the crank handle 2 until the table is at the desired height. 3. Retighten the column lock handle 1 before starting. TABLE TILT ADJUSTMENT TO AVOID UNEXPECTED OR UNINTENTIONAL START-UP, MAKE SURE THAT THE POWER SWITCH IS IN THE “OFF”. 1. Loosen the nuts 4 and 5. 2. Tilt the table to the desired angle. 3. Retighten the nuts 4 and 5.
CHANGING SPEEDS MAKE SURE THE DRILL PRESS HAS COME TO A COMPLETE STOP BEFORE CHANGING SPEEDS. REFER TO THE SPINDLE SPEED SELECTION CHART LOCATED BELOW AND INSIDE OF THE SPINDLE COVER. 1. Disconnect the drill press from the power source. 2. Loosen the two slides bar bolts 1 located on the right and left side of the head. 3. Push the slide motor handle 2 to reposition the motor 3 and loosen the belts. 4. Relocate belt to desired pulley for new spindle speed. 5.
MAINTENANCE TIP: KEEP THE UNIT CLEAN AND FREE OF DUST AND DEBRIS. PAINTED SURFACES CAN BE WIPED WITH A DAMP RAG LUBRICATION Periodically lubricate all sliding or moving parts including the column, rack and the quill shown (use any all purpose grease, available at any hardware store). Note: Bearings in the quill and the V-belt pulley are sealed, permanently lubricated and maintenance free.
RECOMMENDED OPTIONAL ACCESSORIES Here is a sampling of optional accessories available from your local General International dealer to help you increase convenience, productivity, accuracy and safety when using your machine. For more information about our products, please visit our website at www.general.ca item #70-030 item #75-025 ABRASIVE SLEEVES 25 PIECE - RUBBER 10 piece replacement abrasive sleeve set for 70-025. Includes 5 (one of each size) 80 & 120 grit sanding sleeves. Drum sanding set.
PARTS LIST Press Drill (#75-500) IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.
PARTS LIST Press Drill (#75-500) IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.
PARTS LIST Press Drill (#75-500) IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.
DIAGRAM 18
NOTES 19
8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Tel.: (514) 326-1161 Fax: (514) 326-5565 - Parts & Service / (514) 326-5555 - Order Desk orderdesk@general.ca www.general.
