SETUP & OPERATION MANUAL FEATURES Front mounted digital spindle speed display. Electronic inverter variable control adjusts spindle speed from 280-3200 rpm. 17″ DRILL PRESS - ELECTRONIC VARIABLE SPEED Large precision ground cast-iron table with t-slots and coolant trough. Front mounted positive control depth stop. Solid head construction for accuracy and rigidity. Slower speed options ideal for metal drilling applications. Rack and pinion table height adjustment.
GENERAL® INTERNATIONAL 8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Telephone (514) 326-1161 • Fax (514) 326-5555 • www.general.ca THANK YOU for choosing this General® International model 75-700 M1 17” Electronic Variable Speed Drill Press. This drill press has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service.
GENERAL® INTERNATIONAL WARRANTY All component parts of General® International and Excalibur by General International® products are carefully inspected during all stages of production and each unit is thoroughly inspected upon completion of assembly.
TABLE OF CONTENTS Rules for safe operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Grounding instructions.................................................................................................
RULES FOR SAFE OPERATION To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as potential hazards. General® International disclaims any real or implied warranty and holds itself harmless for any injury that may result from improper use of its equipment. 1. Do not operate the drill press when tired, distracted, or under the effects of drugs, alcohol or any medication that impairs reflexes or alertness. 2.
ELECTRICAL REQUIREMENTS BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE WITH GREATER VOLTAGE THAN NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE TO THE MACHINE. IF IN DOUBT, CONTACT A QUALI-FIED ELECTRICIAN BEFORE CONNECTING TO THE POWER SOURCE. THIS TOOL IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS.
17” ELECTRONIC VARIABLE SPEED DRILL PRESS 75-700 M1 IDENTIFICATION OF MAIN PARTS AND COMPONENTS RIGHT SIDE VIEW PULLEY CASE COVER DIGITAL SPEED DISPLAY VARIABLE SPEED CONTROLLER START BUTTON STOP BUTTON CHUCK GUARD TABLE COLUMN BASE COLUMN FLANGE RACK TABLE HEIGHT ADJUSTMENT HANDLE DOWNFEED HANDLES MOTOR BELT TENSION ADJUST LEVER PULLEY CASE COVER SCREW LEFT SIDE VIEW ELECTRONIC INVERTER DEPTH STOP LASER POINTER TABLE LOCK HANDLE CHUCK 7
BASIC FUNCTIONS This model 75-700 electronic variable speed drill press is designed for precision drilling applications in both wood and metal. This unit includes all the basic functions and features found on most standard drill presses and offers the user the added benefit of variable speed control. Featuring a front mounted digital spindle speed display the unit is equipped with two speed ranges.
PLACEMENT WITHIN THE SHOP / ESTABLISHING A SAFETY ZONE PLACEMENT WITHIN THE SHOP This machine should be installed and operated only on a solid, flat and stable floor that is able to support the weight of the sander (275 lbs - 125 kg) and the operator. Using the dimensions shown as a guideline, plan for placement within your shop that will allow the operator to work unencumbered and unobstructed by foot traffic (either passing shop visitors or other shop workers) or other tools or machinery.
INSTALL THE TABLE FIT THE COLUMN RING ONTO THE RACK Insert and hold the rack in the notch in the table bracket and slide the bracket and rack onto the column until the rack bottoms out on the rack seat and fasten two set screws by Allen key. Slide the ring onto the column with the beveled edge facing down to secure the rack to the column. Re-tighten the screw . Note: Do not over-tighten the screw. Note: Position the rack with more teeth towards the bottom .
INSTALL THE CHUCK GUARD REAR VIEW Fit the chuck guard onto the quill and tighten the Phillips screw to secure the chuck guard in place. ADJUSTING AND USING THE CHUCK GUARD 1. Loosen the wing nuts on both sides of the chuck guard and slide the chuck guard extension down along the two slots to the desired height . 2. Tighten the wing nuts to lock the chuck guard extension in place.
ADJUSTMENTS & CONTROLS TABLE SWING ADJUSTMENT TABLE HEIGHT ADJUSTMENT VIEW FROM BACK 1. Loosen table lock handle 2. Turn the table height adjustment handle table is at the desired height. 3. Tighten the table lock handle to lock the table in position. . until the 1. Loosen the table lock handle 2. Swing the table to the desired position the table lock handle. . . Tighten Note: When working with taller workpieces swing the table 180° out of the way and use the base as a table .
CONNECTING TO A POWER SOURCE TO REDUCE THE RISK OF SHOCK OR FIRE DO NOT OPERATE THE UNIT WITH A DAMAGED POWER CORD OR PLUG. REPLACE DAMAGED CORD OR PLUG IMMEDIATELY. SWITCH OFF TO AVOID UNEXPECTED OR UNINTENTIONAL START-UP, MAKE SURE THAT THE POWER SWITCH ON THE DRILL PRESS IS IN THE OFF POSITION BEFORE CONNECTING TO A POWER SOURCE. Once the assembly steps have been completed, uncoil the power cord and plug the power cord into an appropriate outlet.
CHANGING SPINDLE SPEED RANGE TURN OFF AND UNPLUG THE MACHINE FROM THE POWER SOURCE BEFORE OPENING THE PULLEY CASE COVER OR BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS. 1. With the machine turned off and unplugged from the power source, loosen the set screw located on each side of back portion of the headstock using a 4mm Allen key. 2. Using a phillips head screwdriver remove the pulley cover locking screw and open the pulley cover. 3.
MAINTENANCE • Keep the unit clean and free of dust and debris. Painted surfaces can be wiped with a damp rag. • Periodically lubricate all sliding or moving parts including the column and rack purpose grease, available at any hardware store). • Lightly grease the slide bars • Bearings in the quill and the V-belt pulley are sealed and permanently lubricated – no further lubrication is required. (use any all and the quill every two months or as needed depending on frequency of use.
RECOMMENDED OPTIONAL ACCESSORIES We offer a large variety of products to help you increase convenience, productivity, accuracy and safety when using your drill press Here’s a small sampling of optional accessories available from your local General International dealer. For more information about our products, please visit our website at www.general.ca 12” X 24” (305 X 610 mm) 25 piece - Rubber drum Sanding Set Item 70-025 Abrasive sleeves item 70-030 Turn your drill press into a mini drum sander.
47 57 N 58 56 47-3 55 54 47-1 59 53 60 52 123 61 38 51 63 62 37 64 50 47-2 49 39 42 43 41 72 71 67 70 69 47 46 68 33 36 48 65 66 35 34 32 40 45 73 21-1 76 75 26 25 21-2 44 74 24 28 23 27 22 92 91 90 89 88 87 29 86 31 21 85 84 96 20 83N 81 122 30 80 79 77 78 97 93 99 94 82 98 100 95 19 17 18 101 16 102 15 103 104 105 106 110 107 14 13 108 109 12 11 10 121 9 114 119 113 5N 120 112 8 7 111 129 118 117 116 115 6 124
PARTS LIST 75-700 M1 18 PART N0.
PARTS LIST 75-700 M1 PART N0.
PARTS LIST 75-700 M1 NOTES 20 PART N0.
NOTES 21
MODEL 75-700 M1 8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Fax: (514) 326-5565 - Tel.: (514) 326-1161 Fax: (514) 326-5555 - Parts & Service / Order Desk orderdesk@general.ca www.general.ca IMPORTANT When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.
