,'(17,),&$7,21 2) 0$,1 3$576 $1' &20321(176 RIG IDE VIEW S HT L M N K F O J E I P H G G D C Q B A. BASE B. COLUMN C. TABLE PIVOT LOCK LEVER D. TABLE E. FLIP-UP CHUCK GUARD F. MUSHROOM STYLE STOP WITH LOCK-OUT KEY G. MAIN ON/OFF SWITCH H. VARIABLE SPEED CONTROLLER I. DIGITAL SPEED DISPLAY J. LASER SWITCH K. ELECTRONIC INVERTER L. PULLEY COVER M. BELT TENSION LEVER N. MOTOR O. FEED HANDLE P. RACK A Q.
UNPACKING Carefully unpack and remove the unit and its components from the box and check for missing or damaged items as per the list of contents below. NOTE: PLEASE REPORT ANY DAMAGED OR MISSING ITEMS TO YOUR GENERAL® INTERNATIONAL DISTRIBUTOR IMMEDIATELY. LIST OF CONTENTS QTY A. HEAD STOCK ............................................................................ 1 B. BASE ......................................................................................... 1 C. TABLE .............................
CLEANING The protective coating on the machine prevents rust from forming during shipping and storage. Remove it by rubbing with a rag dipped in kerosene, mineral spirits or paint thinner. (Dispose of potentially flammable solvent-soaked rags according to manufacturer’s safety recommendations). A putty knife, held flat to avoid scratching the surface, may also be used to scrape off the coating followed by clean-up with solvent.
ASSEMBLY INSTRUCTIONS BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER CORD IS UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL. INSTALLING THE COLUMN ON THE BASE 1. Set the base on a flat and stable surface, and then install the column on the base. 2. Align the mounting holes in the column with the corresponding holes in the base.
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER CORD IS UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL. INSTALLING THE HEAD STOCK ON THE COLUMN (CONTINUED) A B 3. Center the head stock with the column and the base. 4. Secure the head stock to the column by tightening screws A & B using a 5 mm Allen key. 2.
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER CORD IS UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL. INSTALLING THE TABLE (CONTINUED) 5. Tighten the arm's mounting bolt using a 24 mm wrench. 6. Insert the table into the arm mount as shown. D C A 7. Lock the table in place by turning lever A clockwise. B 8. Slide handle B onto the arbor C as shown D.
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER CORD IS UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL. INSTALLING THE CHUCK GUARD A 1. Slide the chuck guard onto its support as shown A. 2. Tighten the chuck guard using a phillips screwdriver. 2. Tighten each handle using a 9 mm wrench. 2.
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER CORD IS UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL. INSTALLING THE CHUCK (CONTINUED) 3. Fit the arbor into the chuck as shown. 4. Make sure the arbor is inserted all the way into the chuck. 5. Slide the arbor into the quill assembly as shown. 6.
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER CORD IS UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL. INSTALLING A DRILL BIT B A 1. Open the chuck by turning the key A counterclockwise until you can insert a drill bit B. 2. Secure the drill bit in the chuck by turning the key clockwise.
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS. ADJUSTING THE CHUCK GUARD HEIGHT A 1. Loosen the wing nuts A. 2. Position the shield at the desired height, then retighten the wing nuts. ADJUSTING THE DEPTH STOP This drill is equipped with an adjustable depth stop to allow repetitive drilling to a set depth. To set the depth stop: B C 1. Loosen knob B counterclockwise as shown. 2.
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS. PIVOTING THE TABLE 1. Loosen the pivot lock handle as shown. 2. Turn the table to the desired position, and then retighten the pivot lock handle. 2. Turn the crank handle as shown until the table is at the desired height, then retighten the column lock handle. 2. Tilt the table to the desired angle, and then retighten the nut A. ADJUSTING TABLE HEIGHT 1.