MANUALE DI ISTRUZIONI
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Il simbolo del fulmine con la freccia, incluso in un triangolo equilatero, mette in guardia l’utente sui rischi dovuti alla presenza di componenti non isolati elettricamente all’interno dello strumento, che possono costituire pericolo di scosse elettriche.
Sommario Prefazione .......................................................................................................................... 1 Sezione 1 Layout dello strumento .................................................................................................................. Pannello posteriore ........................................................................................................................... Power e Standby ..........................................................
PREFAZIONE Grazie per aver scelto il Promega della GENERALMUSIC. Il Promega rappresenta il vertice della tecnologia applicata agli strumenti musicali. Con l’ausilio della nuova tecnologia proprietaria DRAKE, il Promega offre una potentissima combinazione di generazione sonora che unisce la tecnica dei modelli fisici, con lo stato dell’arte della riproduzione di campionamenti.
Sezione 1 Layout dello strumento Generalmusic Promega 3 Page 1
PANNELLO POSTERIORE (1) (2) (1) MAIN OUT (uscite principali bilanciate ) Right e Left/Mono (2) AUX OUT (uscite ausiliarie ) 1e2 (3) INPUT Right e Left/Mono MIDI (4) In (3) (4) (5) (6) (7) (8) (9) (10) (11) Canale destro e sinistro quando lo strumento è connesso in stereo. Se volete una connessione mono utilizzando un solo cavo, connettete il cavo all’uscita LEFT/MONO ed assicuratevi che nessun cavo sia connesso all’uscita RIGHT. Uscite programmabili 1 e 2.
POWER e STANDBY L’interruttore principale si trova sul pannello posteriore dello strumento. La prima volta che accendete il Promega, la memoria interna dello strumento richiede una fase di decompressione di circa 60 secondi prima di poter essere utilizzata. Nella parte in basso a sinistra sotto la tastiera, trovate il tasto STANDBY. Questo tasto può essere usato in alternativa all’interruttore principale.
Sezione 2 Quick Guide “ Per quelli di voi che non amano leggere i manuali o magari preferiscono farlo in un secondo momento, ecco tutto quello che dovete sapere per usare subito il Promega”.
Il Promega3 è stato pensato per essere semplice da usare ed offrire un accesso immediato a tutte le funzioni principali. Funzioni di base quali sovrapporre suoni (layer), dividere la tastiera in due parti (split) o assegnare gli effetti sono immediatamente accessibili senza ricorrere ad alcun menu di edit e senza utilizzare il display. In questo capitolo troverete le indicazioni principali per utilizzare subito ed al meglio il vostro Promega.
Proviamo insieme a combinare i suoni di tre sezioni in modo che possiate verificare quanto è semplice lavorare con il Promega. Vi raccomandiamo di procedere nell’ordine indicato poiché ogni esempio inizia dalle regolazioni del precedente. ESEMPIO 1: SOVRAPPORRE SUONI (LAYER). Accendiamo lo strumento in modo da avere solo il suono principale di pianoforte attivo. Come potrete notare, solo la prima sezione è attiva (il tasto ON/ OFF della sezione è illuminato).
ESEMPIO 2: CONTROLLARE GLI EFFETTI. Proviamo ora a rendere il nostro suono di string più interessante aggiungendo un effetto CHORUS. PR O EFX 1 CHORUS TREMOLO CHOR/FLANGER CHOR/TREM Nella sezione EFFECTS, utilizzate il Virtual-POT della parte PRO EFX per selezionare l’effetto CHORUS. CHOR/ EXC WAH DELAY ST. DELAY MIDI DELAY COMPRESSOR LOUDNESS Aggiungiamo quindi quest’effetto al suono string. 2 Attivate il tasto PRO EFX nella sezione ORCHESTRA/PAD.
Premendo uno dei tasti SEND, si accede al modo EDIT. Lo slider di ogni sezione vi permette in questo caso, di modificare parametri diversi dal volume della sezione (che è la sua funzione principale). Per indicare che lo strumento è in modo EDIT, tutti i displays, insieme al tasto che avete premuto per attivarlo (in questo caso il tasto SEND) cominciano a lampeggiare. Vi capiterà molto spesso di dover entrare in modo EDIT per regolare alcuni valori o per altre esigenze.
Se volete, potete cambiare il punto di split. Smettete per un attimo di suonare e premete il tasto SPLIT P. nella sezione EDIT & CONTROLS. Tenetelo premuto e con l’altra mano premete il tasto sulla tastiera dove volete posizionare il nuovo punto di split. Rilasciate quindi il tasto SPLIT P. Avrete notato che il display verde della sezione EDIT & CONTROLS ha temporaneamente visualizzato il nome delle note relative al punto di split.
Suonate degli accordi nella parte sinistra e nel frattempo premete il tasto OCTAVE+ nella sezione ORCHESTRA/PAD. Sentirete il suono alzarsi di un’ottava. Premete di nuovo per ottimizzare l’impostazione. - A questo punto non abbiamo più bisogno del suono di basso, quindi spegniamolo. Premete il tasto rosso ON/OFF della sezione BASS/OTHER per eliminare il suono. - ESEMPIO 5: Semplici modifiche dei suoni.
Ora possiamo riportare lo strumento in condizioni normali e per farlo dobbiamo semplicemente premere il tasto che sta lampeggiando, in questo caso il tasto EDIT SOUND. - Premete il tasto EDIT SOUND per disattivare la funzione. Esempio 6: Selezione di una performance (Performance Memories). Una performance è l’insieme di tutte le funzioni dello strumento opportunamente regolate.
Spostarsi su un altro banco richiede due operazioni. Prima dovete selezionare il nuovo banco, Poi selezionare una delle memorie. Non sentirete alcun cambiamento fino a che non avrete completato la seconda operazione. Selezioniamo il PRESET C4. Premete il tasto C. - Potete notare che i tasti cominciano a lampeggiare. Gli unici che non lampeggiano sono quelli che indicano la selezione precedente. Premete il tasto 4.
Dovreste ora sentire la combinazione di pianoforte e archi precedentemente salvata. Salviamo ora un altro suono in una locazione USER. Ritornate all’esempio 2 e 3. Seguite la procedura descritta in entrambi gli esempi in modo da arrivare ad avere un suono di basso a sinistra e pianoforte ed archi a destra. Salviamo quindi questa combinazione di suoni in USER A2. - Premete il tasto STORE. Premete il tasto 2.