Replacement Part List

ITEM
NO.
PART
NO.
DESCRIPTION
QTY.
1
2103227 SWIVEL, DCFSCS22
1
2103226 SWIVEL, DCFSCS22Z
2
2103224 ARM, ROTARY, FSC
1
3
2630010 PLATE, RETAINING
1
4 2500017 COLLAR, SPLIT 1
5
2200093 SHCS
4
6
2200055
SHCS, M8 X 30 1
7
2550161 HANDLE, LOWER
1
8
2550160 HANDLE, FSC, UPPER
1
9
2660047 GRIP, HANDLE
1
10
2660224 PLUG, HANDLE
1
11
2103223 ASSY, BRUSH
1
12 DCG4000FSC
GUN, FSC
1
13
2103228 CASTER KIT,SS
1
14
2702000 HOSE, FSC
1
ITEM
NO.
PART
NO.
DESCRIPTION
QTY.
15 2200053 NUT, M8X1.25 4
16
D10079 PLUG, 3/8 X 3/8-M
1
17
D10075 COUPLER, 3/8 X 3/8-M
1
18
2500016 BLOCK, HANDLE
2
19 2200094 BOLT, M6 8
20
2203406 WASHER, M6
8
21
2200026 NUT, NYLOK, M6
2
22
2202010 PIN, 55MM, W/RING, SS
2
23
2200058 HHCS, M6 X 60
2
24
2200018 WASHER, M6
4
25
2203507 WASHER
1
26
2540070 DECK, FSC, SST
1
27
D40015 FILTER, IN-LINE, SST
1
28
2660297 GROMMET, FSC HANDLE
2
General Pump
1174 Northland Drive • Mendota Heights, MN 55120
Phone: [phone] • Fax: [phone]
www.generalpump.com • [e-mail]
Ref 300918 Rev. B
05-16
Operating Pressures: 1,000 to 4,000 PSI
Max Flow: 8.0 GPM
Dimensions: 70” x 23” x 23”
Weight: 24.5 lbs.
Operating Instructions
1. Connect inlet filter, D40014, to FSC gun inlet.
2. Connect to Pressure Washer.
3. Turn water on and open valve. Open trigger gun for flow of water
through nozzles. Nozzles must have flowing spray. If not, remove
tips and clean; reassemble, making sure that groove of nozzle is
parallel to spray bar. Use thread sealant when installing nozzles.
4. Start Pressure Washer. The Hammerhead is ready for operation.
5. Walk slowly behind the Hammerhead cleaning as you go. If
striping occurs, slow down your pace.
6. Periodically check weep hole on bottom of swivel. Water will
seep slowly; if water shoots out, stop and replace seals. Swivel
assembly can be rebuilt.
7. For maximum effectiveness keep spray tips clean. If the machine
vibrates, stop and clean spray tips.
8. For the DCFSCS22Z ONLY: Grease the swivel with one or two
grease gun pumps every 200 hours (or once about every 30 days of
use).
NOTE: After 50 hours of use, remove the inlet filter, take apart and clean
filter screen.
DO NOT ALLOW MACHINE TO REMAIN STATIONARY
ON SOFT SURFACES SUCH AS WOOD.
Caution: Striking any raised obstacle during operation will damage
machine. If contact does occur and results in vibration when
operating machine, STOP and replace spray bar. Continued
operation could result in serious injury or damage to machine.
Ref 300918 Rev. B
05-16