Instructions / Assembly

Assembly Instructions
Hook-On Trees
Each carton contains one top section, one center pole with color-
coded branch brackets (larger trees include additional poles), one
tree stand and color-coded branches.
1. Unfold tree stand and insert eye bolts. Remove packing material
from ends of poles. Insert center pole(s) securely into stand.
2. BRANCH SHAPING. (Branches should be attached to tree pole
from the bottom up.) Locate the color-coded branches that match
the color code of the bottom bracket on the center pole (Figure 1).
Each branch must be shaped to a natural position by spreading
out the left and right tips away from
the center tip (Figure 2). See
Shaping Instructions on page 4.
3. After all bottom bracket branches
are properly shaped they can be
attached to the center pole brackets.
Gently push each branch down into
the bracket slots until they lock into
place (Figure 3).
4. Continue to work your way up the
Fig. 4
Fig. 3Fig. 2
Fig. 1
CAUTION: IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Do not use seasonal products outdoors
unless marked suitable for indoor and
outdoor use. When products are used in
outdoor applications, connect the product
to a Ground Fault Circuit Interrupter
(GFCI) outlet. If one is not provided,
contact a qualified electrician for proper
installation.
• This seasonal use product is not intended
for permanent installation or use.
• When decorating trees, use miniature
light bulb strings or LED light strings only.
“C” size bulbs are not recommended.
• Do not mount or place near gas or electric
heaters, fireplaces, candles or other
similar sources of heat.
• Do not secure the wiring of the product
with staples or nails, or place on sharp
hooks or nails.
• Unplug the product when leaving the
house, when retiring for the night, or if left
unattended.
• CAUTION: This is an electrical product –
not a toy! To avoid risk of fire, burns,
personal injury and electric shock, it should
not be played with or placed where small
children can reach it.
• Do not let lamps rest on the supply cord or
any wire.
• Do not use this product for other than its
intended use.
• Do not hang ornaments or other objects
from cord, wire or light string.
• Do not close doors or windows on the
product or extension cords as this may
damage the wire insulation.
• Never operate this product if the power
cord or plug is damaged.
• Use only manufacturer specified
replacement bulbs.
• Read and follow all instructions that are on
the product or provided with the product.
USE AND CARE INSTRUCTIONS
• When storing the product, carefully remove
the product from wherever it is placed,
including trees, branches, or bushes, to
avoid any undue strain or stress on the
product conductors, connections, and wires.
• When not in use, store neatly in a cool, dry
location protected from sunlight.
FOR INDOOR USE ONLY. Retain carton for storage purposes.
CONTENTS
Hook-On Trees . . . . . . . . . . . . . . . . . . . . . . . 1
Hinged and Wrapped Trees . . . . . . . . . . . . . 2
Pre-Lit Hinged and Wrapped Trees . . . . . . . 2
Low-Voltage Trees . . . . . . . . . . . . . . . . . . . . 3
Shaping Instructions . . . . . . . . . . . . . . . . . . 4
Bulb Replacement . . . . . . . . . . . . . . . . . . . . 4
FuseReplacement . . . . . . . . . . . . . . . . . . . . 4
S
torage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Limited Warranty . . . . . . . . . . . . . . . . . . . . . 4
pole shaping and attaching branches as described above.
5. When all tree branches have been attached, the tree top section
can be shaped and attached. Shape the tree top as you did the
lower branches.
6. Push bottom of tree top into green plastic “pole cap” at top of
center pole until it is firmly seated (Figure 4). Assembly is now
complete.
7. You may wish to further shape your finished tree as desired.
SAVE THESE INSTRUCTIONS
Scan this with
your smart phone
to be directed to
assembly videos.
A Tree Assembly and Shaping Video is available online. Please visit
the Customer Service tab at www.nationaltree.com to view.
1