GCOT335 3” High-Speed Electric Cut-Off Tool Tronçonneuse à métaux électrique haute vitesse de 7,6 cm Herramienta eléctrica de corte de alta velocidad, de 3” Operator’s Manual Manuel d’utilisation Manual del Operario 888-552-8665 TOLL FREE HELP LINE: WEBSITE: www.genesispowertools.
English SPECIFICATIONS • • • • • • Model:------------------------- GCOT335 Rated Power: ----------------- 120V~/60Hz, 3.5 Amp No Load Speed: --------------- 24,000 RPM Disc Size: --------------------- 3” (76mm) Max Cutting Depth: ----------- 1" (25mm) Net Weight: ------------------- 3.2 lbs Includes: 3” Cut-off Disc, Arbor Wrench and Hex key Warning: To reduce the risk of injury, user must read and understand this operator’s manual before operating this tool. Save this Manual for future reference.
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adaptor plugs in any earthed (grounded) power tools. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way.
English • Turn power tool off, and disconnect the plug from the power source and/or battery pack from the power tool before making any adjustments, changing the accessories, or storing the tools. Such preventive safety measures reduce the risk of an accidental start up which may cause personal injury. • Store idle tool out of reach of children and other inexperienced persons. It is dangerous in the hand of untrained users. • Maintain power tools with care.
• If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in Canada) to indicate that it is acceptable for outdoor use. • Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. • Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
English • Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock • Causes and operator prevention of Kickback: Kickback is a sudden reaction to a pinched or snagged rotating cutting disc. Pinching or snagging causes rapid stalling of the rotating disc which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.
Warning: Read and understand all warnings, cautions and operating instructions before using this equipment. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS English > Use extra caution when making a pocket cut into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.
English SYMBOLS Some of the following symbols may appear on this product. Study these symbols and learn their meaning. Proper interpretation of these symbols will allow for more efficient and safer operation of this product. SYMBOL DESCRIPTION SYMBOL DESCRIPTION V Volts A Amperes Hz Hertz Class II construction Double Insulated construction W Watts Warning symbol.
KNOWING YOUR CUT-OFF TOOL 4 1 2 English 3 8 7 6 5 1. 2. 3. 4. FIG 1 ON/OFF Switch Motor Guard Guard Locking Lever 5. 6. 7. 8. Cut-Off Disc Disc Locking Screw Arbor Wrench Hex Key UNPACKING AND CONTENTS IMPORTANT: Due to modern mass production techniques, it is unlikely the tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.
English NOTE: Place the detent (6) so it will slide over the slot (5) in the guard mount • When the guard clamp is fully onto the guard mount, rotate the guard 180° so it is positioned at the top of the tool. • Press the guard locking lever firmly inward toward the tool to lock the guard (3) on to the tool. 2 4 INSTALLING THE CUT-OFF DISC (FIG 3) Warning: Make sure the replacement cut-off disc is rated for at least 24,000 RPM and is in good condition. 6 3 5 1 FIG 2 1. Unplug the tool. 2.
APPLICATION Warning: Always clamp the workpiece firmly into a vise or to a stable work surface. Never hold the workpiece with one hand and the tool with the other hand. Severe injury may result. Warning: Always wear appropriate eye, ear and breathing protection and protective clothing when operating the cut-off tool. 1. 2. 3. 4. 5. Mark the workpiece where the cut is to be made. Firmly clamp the workpiece in a vise or to a stable work surface.
English TWO-YEAR WARRANTY This product is warranted free from defects in material and workmanship for 2 years after date of purchase. This limited warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser is covered by this warranty and it is not transferable. Prior to returning your tool to store location of purchase, please call our Toll-Free Help Line for possible solutions. THIS PRODUCT IS NOT WARRANTED IF USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.
Richpower Industries, Inc. 736 Hampton Road Williamston, SC USA www.genesispowertools.com 2016.
