Instructions / Assembly
PN# 37026500123 05/15/2009
16
3. Securely fasten wires.
• Securely fasten wires to ceiling and
wall using insulated staples provided.
– Use insulated staples.
– Staples should be snug only.
• If rear cover is attached to power head,
remove it.
• On power head:
– Route Wall Control wires through wire guide
on power head.
– Split and strip ends of wire (Fig. 3-2 on
previous page).
–Insert wire into terminal holes and lightly press in
the orange locking clips above each terminal
hole. (You can use a pencil or small screwdriver
to comfortably press in locking clips.) The white
wire into #1 terminal hole and striped wire into
the #2 terminal hole.
–Confirm wire lock by lightly tugging on the wire.
The wire should remain in the terminal hole.
• Do NOT install rear cover yet.
4. Mounting.
• Fasten Wall Control to wall with 2 screws
(provided) (Fig. 3-4).
• Remove protective backing from "Entrapment"
warning label (Fig. 3-5). The "Entrapment" label
is located in the center of this manual.
– Stick label on wall near Wall Control.
FIG. 3-4 Mounting Wall Control.
Chil
dcanbe p
in
n
ed u
nd
er autom
a
t
ic
gara
ge
doo
r.
D
ea
th or ser
io
u
s in
jury
can
res
u
lt.
•
N
e
v
er let
ch
i
ld w
a
l
k o
r ru
n
u
n
de
r
m
o
v
ing
d
o
or
.
.
•
N
e
v
e
r let
ch
i
ld
u
se
d
o
o
r op
en
e
r c
o
n
trols
.
•
A
lw
a
ys
ke
e
p m
o
v
in
g
do
o
r in sight.
•
If p
er
son
is pin
n
e
d
,
pu
s
h co
n
tro
l
b
u
tto
n
or use
em
er
ge
nc
y re
le
a
se
.
•
Te s
t doo
r ope
ner
m
on
thly:
R
e
fer
to you
r
ow
ner'
’
sm
a
n
ua
l
.
P
la
c
e
1
1
/
2
-inch
o
b
jec
t (or
2x
4
la
i
d f
lat) on f
loo
r
.
If
do
o
r
f
a
il
s to reve
rse
on co
n
ta
ct,
ad
j
ust
o
p
e
ne
r.
If op
e
n
er
still
fail
s to re
v
ers
e d
o
o
r
,
repa
ir
o
r rep
la
ce ope
n
er
.
D
o n
ot
re
move
o
r
p
ai
n
t
o
ve
r
th
is
la
be
l
.
M
ou
nt wall
control ou
t
of chi
ld's reach
(at lea
st
5
fee
t
abov
e floor)
.
Plac
e next to wal
l
con
trol.
©
199
9
Insulated
Staple
+–
PB
Infared Sensor
123456
FIG. 3-3 Insert wires
.
(Power Head With Rear Cover Removed)
1234
Terminal
Holes
Locking
Clips
56
FIG. 3-5 Mounting Entrapment warning label.
3
2
1
Independent Light Control
–
Controls door opener lights from inside garage
–
Energy-Saver shut-off turns OFF lights 3 minutes after
door activation
Vacation Locking Switch
– LOCK disables controls after
door is completely closed
– UNLOCK allows controls to
work normally
Door Control "Open/Close" Button
–
Open and closes door from
inside garage
wire guide