PRE-PROGRAMMED REMOTE INCLUDED FOR QUICK & EASY INSTALL Serial Number Decal BELT/CHAIN DRIVE GARAGE DOOR OPENER MODELS 1035, 2035, 2036, 2055, 3035, 3055, 7035, 7055 OPERATION & MAINTENANCE MANUAL Includes INTELLICODE® Remote Control. Safe-T-Beam® system must be installed to close the door. For use only with residential sectional overhead garage doors. Homelink® and Car2U® compatible Need help or have questions? For answers and assistance, STOP visit www.GenieCompany.
T Safety Information Safety Notifications................................................ 1 Important Safety Instructions ............................ 1 Important Installation Instructions .................. 2 Features Safety Features ........................................................ 3 Opener Features ..................................................... 3 Safe-T-Beam Protection Function ..................... 3 Wall Console Features ...........................................
Safety Information OVERVIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMATION Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual.
Safety Information IMPORTANT INSTALLATION INSTRUCTIONS ! WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. If you have any questions or do not understand an instruction, call The Genie Company. • DO NOT install operator on an improperly balanced door. An improperly balanced door could cause severe injury.
Features Begin here ONLY AFTER completing assembly and installation of the opener. Review the Assembly and Installation Poster to ensure all steps have been performed. Visit www.GenieCompany.com to download a printable file. SAFETY FEATURES OPENER FEATURES Safe-T-Beam® (STB) Non-Contact Reversing System Puts an invisible beam across the door opening. The door stops and reverses to the full open position if anything passes through the beam.
Wall Control Features One of the following wall controls will be included. NOTE: Wall consoles from other manufactures may not work with this new opener. Use only the wall control provided with this unit. See warning. SERIES II WALL CONSOLE Open/Close Button Opens and closes door from inside garage. Indicator Light -Red indicator backlight is ON. -When Sure-Lock™ in ON, indicator is off. Sure-Lock™ Button -LOCK disables controls after door is completely closed. -UNLOCK allows controls to work normally.
Programming Overview NOTE: Before programming the operator, check to make sure there are no objects in the garage door opening. INTRODUCTION Now that the Genie® garage door opener is installed, follow the steps in this manual to program the opener so that the door opens and closes properly and all remote devices operate correctly. The following steps are a guide to setting opener so it functions properly. The following steps list the order of programming the opener’s functional settings for use. 1.
Programming Information TRAVEL LIMITS ! • WARNING Make sure doorway is in full view and clear of obstacles and people to avoid injury or property damage. DO NOT operate this unit from the wall control before LIMITS are set. Severe damage to the opener could occur. The carriage MUST be engaged to turnbuckle BEFORE setting limits. See installation poster (if provided) or call Customer Service at 1-800-35-GENIE or visit www.GenieCompany.com. DO NOT set limits with Battery Backup attached.
Programming Information Opening Garage Door (Up Limit) NOTE: Beginning with garage door closed is recommended but not necessary. READ AND UNDERSTAND STEPS 6-9 BEFORE PROCEEDING 6. Press and hold the UP arrow button (+) for two seconds or until the long LED comes on blue. (The round LED stays off.) 9. Press and release the program/set button—both LEDs flash blue and then go off. The UP (OPEN) TRAVEL LIMIT IS NOW PROGRAMMED. Steady Blue Flashing Blue 7.
Wall Control Operation Force Control Contact Reverse Test The force controls are automatically set when the wall control is used for the first time with garage door opener. The door MUST complete one full cycle, from full open to full close and then, full close to full open, before the settings are automatically recorded. NOTE: The limit and Force settings MUST BE COMPLETED before performing the Contact Reverse Test. 12.
Remote Control Programming REMOTES NOTE: THE REMOTE CONTROLS INCLUDED WITH THIS OPENER, HAVE BEEN PRE-PROGRAMMED AT THE FACTORY FOR YOUR CONVENIENCE. NOTE: The following instructions are for remote control transmitters purchased separately in addition to those provided with this opener, but can also be used if any remote(s) may require re-programming. 3. Slowly press and release the remote button two times. The opener LEDs will flash and go off, indicating it has been successfully programmed to the remote.
Programming Wireless Keypad (Optional on some models) Tip: Program Keypad before mounting. Keypad Overview: Synchronizing Keypad to Door: 1. Press PROGRAM SET button two seconds until the round LED turns blue, then release. The long purple LED will blink. BLINKING PURPLE 2. 3. 4. 5. Key in the new PIN on the keypad. Press Up/Down key and opener LEDs will stay on steady. Press Up/Down key again and opener LEDs turn off. Press Up/Down key a third time and opener runs.
Programming Wireless Keypad (Continued) Door Operation with Wireless Keypad: Mounting Keypad To open and close a single door with the Keyless Entry Pad, enter the PIN number and press Up/Down Key (enter). The keypad MUST be mounted within sight of the garage door(s) at least five feet above the floor and clear of any moving door part. For multiple doors enter the PIN number, press the UP/Down Key once and enter the door number (1,2 or 3). 1. Remove battery cover and batteries. 2.
Programming Vehicle Remotes Programming HomeLink® System Step 1 Clear HomeLink Clear HomeLink by pressing and holding down the first and third buttons until the indicator on the HomeLink blinks slow and then fast for 20 seconds; then release both buttons. NOTE: Clearing the HomeLink will remove all previously programmed garage door openers. Step 2 Train HomeLink to the Genie Remote Choose the button on the HomeLink that will be used to open the door.
Clearing Remotes CLEARING MEMORY OF REMOTES NOTE: Clearing memory of remotes from the powerhead will clear ALL programmed remotes and wireless keypads. The opener will no longer recognize any signal from any remote device, including a missing remote device. All remaining (or recovered) remotes and wireless keypads MUST be reprogrammed as shown in pages 9,10,12. NOTE: The garage door opener will operate normally using the wall console. 3.
Maintenance and Adjustments For help, call customer service at: 1-800-35-GENIE or visit www.GenieCompany.com IMPORTANT SAFETY INSTRUCTIONS ! WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH, READ AND FOLLOW ALL INSTRUCTIONS. 1. NEVER let children operate or play with the door controls. 2. Keep remote away from children. 3. ALWAYS keep the moving door in sight and away from 4. 5. 6. 7. people and objects until door is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
Maintenance and Adjustments (continued) Regular Maintenance Basic monthly maintenance tasks include: • • • • • • • Contact Reverse Test Lubricate door hardware Safe-T-Beam® System check Door balance Remote Battery Replacement (As needed) Light Bulb Replacement (As needed) Chain/Belt Tension A. Contact Reverse Test See page 8. B. Lubricate Door Hardware Inspect door rollers and hinges and lubricate as needed using a light weight general purpose grease. C.
Maintenance and Adjustments (continued) F. Light Bulb Replacement ! • • • • • WARNING Use extreme caution when working from a ladder or step stool or serious injury can occur. When replacing light cover, make sure wires are not pinched or near moving parts. Use only properly rated incandescent, LED or CFL light bulbs. DO NOT use bulbs with a rating greater than 60 Watts. Use A19 size light bulbs. DO NOT use bulbs having a short neck.
Maintenance and Adjustments H. Adjust Carriage for (optional) Emergency Release System Rail, Chain, & Door Arms not shown for clarity The carriage on this opener can be adjusted to work with the Emergency Release Cable Lock System (available at your local Genie® Retailer). 1. Operate door to mid position. 2. Pull emergency release cord and manually close door. 3. Make sure carriage latch is in the upright (engaged) position. 4. Remove (2) 5/16” machine screws and cap. 5.
Maintenance and Adjustments Multiple Garage Doors • NEVER position Safe-T-Beam® modules where signals will cross. • Place the Transmitter (Red LED) Safe-T-Beams on adjacent doors facing in opposite directions. LOCATING SAFE-T-BEAM® PAIRS Transmitter (RED LED) and Receiver (GREEN LED) NOTE: Direct sunlight creates interference with Safe-T-Beam® Receiver (Green LED).
Troubleshooting Need help or have questions? DO NOT RETURN to the store. Visit www.genicompany.com or call Customer Service at 1-800-35-GENIE. PROBLEM: WHAT TO DO: Opener does NOT operator when wall control is pressed. • Turn Sure-Lock™ OFF See page 4. • Check power source. – Plug a lamp into outlet used for powerhead. If lamp works, power source is OK. – If not, check fuse or circuit breaker. • If power is OK, – Check connections at powerhead terminals and at wall console.
Troubleshooting OPERATION (continued) PROBLEM WHAT TO DO Noisy operation. • Be sure all door fasteners are tight. • Be sure garage door is in good repair, properly lubricated and balanced. • Be sure opener is in good repair. Door opener runs slow. • Check operating condition of door. Door may need professional repair/adjustment. • Is this opener installed on a one-piece door? This opener is not designed to operate a one-piece door.
Genie Battery Backup (BBU) Battery backup devices from other manufacturers will not operate with this opener. Use only Genie Battery Backup type battery that was provided. Genie P/N 111658-0002 Installing Genie Battery Backup For units that included with optional battery backup (BBU) 1. Unplug powerhead from power source. 2. Tilt BBU approximately 450 and lower into slots in the top rear of the powerhead. 3. Fasten to powerhead with 2 supplied self tapping screws. NOTE: There are no holes in rear cover.
Genie Models 1035, 2035, 2036, 2055, 3035, 3055, 7035, 7055 Limited Warranty GMI Holdings, Inc.
