Refer to the assembly poster for opener assembly and installation instructions. Return to this manual for programming, operation and maintenance. BELT/CHAIN/SCREW DRIVE GARAGE DOOR OPENER PROGRAMMING, OPERATION & MAINTENANCE MANUAL t 4UBOEBSE .PEFMT t ##6 .PEFMT t J%$. .PEFMT t *OUFHSBUFE -&% MJHIUFE .PEFMT t *ODMVEFT 3FUBJM 1SPGFTTJPOBM .PEFMT DO NOT use photocells from other manufacturers or openers with this opener.
INDEX Safety & General Information Introduction .............................................................. 1 Safety Notifications................................................. 2 Important Installation Instructions ................... 3 ScrewDrive 2 Standard & Safety Features ....................... 4 Scan this code for a video of this installation or visit: www.geniecompany.com 3 Programming Information Introduction to opener programming ............ 5 Setting the DOWN Limit ...................
1 INTRODUCTION Thank you for purchasing a Genie® brand garage door opener. The leader in garage door opener technology. Please take a moment to preview this manual and assembly poster to ensure that you have the proper tools and general assembly and fabrication skills required to install a new garage door opener. Read and understand all Safety Warnings and Cautions contained in this manual before proceeding.
SAFETY NOTIFICATIONS & INSTRUCTIONS OVERVIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMATION Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual.
IMPORTANT INSTALLATION INSTRUCTIONS ! WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. If you have any questions or do not understand an instruction, call The Genie Company. t DO NOT install opener on an improperly balanced door. An improperly balanced door could cause severe injury. Repairs and adjustments to cables, spring assembly and other hardware must be made by a trained service person using proper tools and instructions.
2 SAFETY & STANDARD FEATURES 4 7 8 5 6 3 Vehicle Compatible 2 1 4BGF 5 #FBN¥ 45# /PO $POUBDU 3FWFSTJOH 4ZTUFN t Places an infrared beam across the door opening. t Only affects the DOWN travel of the door. t Stops an open door from closing or reverses a door while in the down travel. t Reversing system can be overridden with constant pressure on the wired wall console only. t The door will stop and reverse to the full open position if beam is obstructed.
3 OPENER PROGRAMMING & ACCESSORY INSTALLATIONS NOTE: Before programming the opener, check to make sure there are no objects in the garage door opening. DO NOT allow persons to enter the area of the door while programming and operating. The following steps list the order of programming the opener’s functional settings and install any accessories that were included with the opener or purchased separately. These steps should be performed in order. 1. Down Travel Limit 2. Up Travel Limit 3. Force Control 4.
PROGRAMMING DOWN TRAVEL LIMIT ! t t t t ! t t t t WARNING Make sure doorway is in full view and clear of obstacles and people to avoid injury or property damage. DO NOT operate this unit from the wall control before LIMITS are set. Severe damage to the opener could occur. The carriage MUST be engaged to turnbuckle BEFORE setting limits. See installation poster or call Customer Service at 1-800-35-GENIE or visit www.geniecompany.com. DO NOT set limits with Battery Backup attached.
PROGRAMMING UP TRAVEL LIMIT 1-2. Enter Programming Mode Programming UP Limit: 1. Press and hold the UP arrow button. t Long LED will light BLUE. 2. Release UP arrow button. t Round LED will flash BLUE. 3. Press and hold the UP arrow button until door is fully open. t Use the DOWN arrow button if door opens too far. Use both UP and DOWN buttons to adjust open travel as necessary. Steady Blue SET Flashing Blue SECTIONAL DOOR UP LIMIT: Door should fully open so that door seal is even with door header.
PROGRAMMING FORCE AND CONTACT REVERSE Force Control Contact Reverse Test The force controls are automatically set when the wall control is used for the first time with garage door opener. The door MUST complete one full cycle, from full open to full close and then, full close to full open, before the settings are automatically recorded. NOTE: The limit and Force settings MUST BE COMPLETED before performing the Contact Reverse Test. ! WARNING 1.
PROGRAMMING ADDITIONAL REMOTE CONTROLS THE REMOTE CONTROLS INCLUDED WITH THIS OPENER HAVE BEEN PROGRAMMED AT THE FACTORY FOR YOUR CONVENIENCE. NOTE: The following instructions are for remote control transmitters purchased separately in addition to those provided with this opener, but can also be used if any remote(s) may require re-programming. NOTE: Each programming step has a 30 second time limit for completion after the function is initiated.
PROGRAMMING KEYPAD (abbreviated) 2VJDL7JFX 4JOHMF %PPS TFUVQ Please see complete instructions that accompany keypad Activate keypad by opening battery compartment and pull protective tab. Reinstall compartment door to begin programming. NOTE: Keypad will remain active for 15 seconds after a successful entry is made. During this 15 seconds ANY key will operate the opener. TAB Scan Code for a video of the complete installation and programming. Program Keypad before mounting.
PROGRAMMING VEHICLE SYSTEMS Programming HomeLink® System Step 1 Clear HomeLink Clear HomeLink by pressing and holding down the first and third buttons until the indicator on the HomeLink blinks slow and then fast for 20 seconds; then release both buttons. NOTE: Clearing the HomeLink will remove all previously programmed garage door openers. Step 2 Train HomeLink to the Genie Remote Choose the button on the HomeLink that will be used to open the door.
PROGRAMMING TO USE ALADDIN CONNECT® 1FSGPSN UIFTF TUFQT POMZ BGUFS PQFOFS JT GVMMZ JOTUBMMFE QSPHSBNNFE BOE UFTUFE IMPORTANT SAFETY INSTRUCTIONS CONSIGNES DE SÉCURITÉ IMPORTANTES WARNING AVERTISSEMENT TO REDUCE THE RISK OF SEVERE INJURY OR DEATH, READ AND FOLLOW ALL INSTRUCTIONS. 1. Never allow children to operate or play with door controls. 2. Install the entrapment WARNING placard next to the wall control in a prominent location. 3. NO PERSONS SHOULD CROSS THE PATH OF A MOVING DOOR. 4.
2 Download the Aladdin Connect® app (Unless using 3rd party app) Scan for iOS app Versions 8 and higher Scan for Android app Versions 4.4 and higher Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. 3 Follow the Aladdin Connect® app instructions Follow steps per the app instructions. t Create an account t Set up opener(s) t Add users t Set rules and notifications.
4 MAINTENANCE IMPORTANT SAFETY INSTRUCTIONS WARNING ! To reduce the risk of severe injury or death, read and follow all instructions. 1. 2. 3. 4. 5. 6. 7. NEVER let children operate or play with the door controls. Keep remote away from children. ALWAYS keep the moving door in sight and away from people and objects until door is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR. NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR. Test opener monthly.
Regular inspection/maintenance for the door and opener should be performed at regular intervals to ensure the system runs at peak safety, performance and efficiency. MAINTENANCE ITEM INTERVALS DETAILS Contact Reverse Test Monthly See Page 8 to run system test. Lubricate Door Hardware Monthly Lubricate Rollers & Hinges with a light weight general purpose grease. Safe-T-Beam® system check Monthly Check wiring for loose connections, cracks or worn insulation. Clean lenses of dirt & debris.
B Replacing Batteries 3FNPUF #BUUFSZ 3FQMBDFNFOU CVUUPO Replace remote battery with a CR2032 coin cell battery. 1. Slide the battery cover off. 2. Slide out the old battery and slide in the new. Be sure positive side (+) is UP. 3. Slide the battery cover on until it snaps into place. 3FNPUF #BUUFSZ 3FQMBDFNFOU CVUUPO Replace remote battery with a CR2032 coin cell battery. 1. Open remote case using a washer or coin that fits into the slot on the top of the remote. 2. Replace battery.
5 SPECIAL INSTALLATION INFORMATION Changing Force Settings ! WARNING ! TO AVOID INJURY OR DAMAGE t NEVER adjust the force settings to adjust for damage, including an unbalanced door, binding door track or broken spring. t Perform a CONTACT REVERSE TEST monthly. AVERTISSEMENT Pour éviter les blessures ou des dommages t NE JAMAIS régler la force pour compenser des dommages, y compris une porte mal équilibrée, un rail de porte coinçant ou des ressorts cassés.
CLEARING MEMORY OF ACCESSORIES NOTE: Clearing memory of remotes from the powerhead will clear ALL programmed remotes, wireless keypads and vehicle transmitters. The opener will no longer recognize any signal from any remote device, including a missing remote device. This does not include the Aladdin Connect® or Wireless Wall Console. All remaining (or recovered) remotes, vehicles and wireless keypads MUST be reprogrammed. NOTE: The garage door opener will operate normally using the wall console. 1.
Adjusting Speed Control Speed Settings (DC Models only) Speed settings are pre-programmed at the factory for the maximum speed. Speed settings should not need adjustment with this unit. However, travel speed for the opener can be adjusted to a slower speed in both the Open and Close directions, to minimize wear on heavier sectional doors.
Installing Safe-T-Beams® on multiple garage doors (Preventing “cross-talk”) LOCATING SAFE-T-BEAM® PAIRS Transmitter (RED LED) and Receiver (GREEN LED) Multiple Garage Doors t NEVER position Safe-T-Beam® modules where signals will cross. t 1MBDF UIF 5SBOTNJUUFS 3FE -&% 4BGF 5 #FBNT PO adjacent doors facing in opposite directions. NOTE: Direct sunlight creates interference with SafeT-Beam® Receiver (Green LED).
6 TROUBLESHOOTING Use the guide below along with the self diagnostic powerhead LEDs to help troubleshoot any problems. Need help or have questions? DO NOT RETURN to the store. Visit www.genicompany.com or call Customer Service at 1-800-35-GENIE. PROBLEM: WHAT TO DO: Opener does NOT operate when wall control is pressed. t 5VSO 4VSF -PDL 0'' 4FF QBHF t $IFDL QPXFS TPVSDF – Plug a lamp into outlet used for powerhead. If lamp works, power source is OK. – If not, check fuse or circuit breaker.
TROUBLESHOOTING POWERHEAD LEDS Powerhead LED Round LED Long LED 22 Solution Possible Problem Normal operation. None required. No response from unit. Check power supply. Contact a trained door system professional. Limits NOT set properly. Re-program limits, see pages 6-7. Program error. Unplug unit, wait 5 seconds, plug in. Component failure. Contact a trained door system technician. OFF Remote NOT programmed. Program remote, see page 9. ON/PURPLE/ FLASHING OFF Remote NOT programmed.
7 REPLACEMENT PARTS Specify model number of opener when ordering parts Some hardware listed here shows size and/or type so they may be sourced locally if lost. Complete hardware bags can be ordered separately. Chain & Belt Channel Item Description QTY.
DC Chain/Belt Drive Powerhead 4A 1 4 3 5A 5A 9 5A 5 10 11 8 6 7 6A Specify model number of opener when ordering parts 24 Item Description QTY.
Screwdrive Channel Specify model number of opener when ordering parts D Item Description QTY.
AC ScrewDrive Powerhead Specify model number of opener when ordering parts 26 Item Description QTY.
DC ScrewDrive Powerhead 1 2 3 4 4A 5A 5A 9 5A 5 10 11 8 6 7 6A Specify model number of opener when ordering parts Item Description QTY.
8 ! DASMA SAFETY GUIDELINES Look for this Safety Alert Symbol below. This symbol indicates a potential personal safety hazard that can result in injury or death. A GARAGE DOOR IS THE LARGEST MOVING OBJECT IN THE HOME. These doors are often operated by electric door openers. Proper installation, operation, maintenance, and testing of the garage door and automatic opener are necessary to provide safe, trouble-free operation.
DASMA SAFETY GUIDELINES The push button wall control should be out of reach of children. (at least 5 feet from the floor) and away from all moving parts. Mount and use the button where you can clearly see the moving garage door. ! WHEN USING THE PUSH BUTTON OR TRANSMITTER, KEEP THE DOOR IN SIGHT UNTIL IT COMPLETELY STOPS MOVING. Teach children never to play under or near an open garage door. ! GARAGE DOOR OPENERS ARE NOT TOYS.
The Genie Company 1 Door Drive Mount Hope Ohio 44660 1-800-35-GENIE (354-3643) www.geniecompany.
