User Manual

40681504323, 06/2019
WARNING
!
MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.
•DO NOT install transmitter unless the door operator’s safety device works as required by the door
operator’s manual.
•Wall Console must be mounted in sight of door, at least 5 feet above oor and clear of moving
door parts.
•Keep people clear of opening while door is moving.
•DO NOT allow children to play with the transmitter or door operator.
If safety reverse does not work properly:
•Close door then disconnect opener using the manual release handle.
•DO NOT use transmitter or door operator.
•Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.
FCC Part 15.21 Statement:
Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation of the device.
NOT FOR USE WITH ANY GARAGE DOOR OPENER MANUFACTURED PRIOR TO 1993.
SAFETY BEAMS (PHOTOCELLS) MUST BE IN PLACE AND OPERATIONAL.
THINGS TO KNOW BEFORE STARTING:
- During programming, the garage door opener may operate. Ensure that the garage door opening is clear of
personnel or any obstructions.
- Do not to press the LEARN button for longer than the noted 2-3 seconds as it could cause your existing,
operational remotes and keypads to no longer work.
Below are the brands and specications that this remote is compatible with and the available methods that can be
used to program them. Review Chart A for compatibility and method, then proceed to STEP 1.
NOTE: During programming, the garage door opener will operate. Ensure that the
garage door opening is clear of personnel or any obstructions.
Chart A
PARTS
Visor Clip
Visor Clip
Holder
Key Chain
* CHAMBERLAIN® YELLOW LEARN BUTTON INSTRUCTIONS:
Changing the Battery:
Remove small phillips
head backing screw.
Pry case open
with small coin or
screwdriver.
Replace battery with
CR2032 coin cell.
For use with Chamberlain® technology with a YELLOW LEARN button:
1. On the garage door opener, press the LEARN button for 2-3 seconds and then release.
2. On the universal remote, press and release the pre-set button OR the button you just programmed
once every 2 seconds until the garage door opener operates. Let it run until it stops.
TIP: Allow the LED light on the universal transmitter to stop ashing before your next button press.
3. Repeat steps 1 and 2 above.
4. Test the button - programming is complete.
AVAILABLE PROGRAM METHOD
QUICK START
METHOD
LEARN
METHOD
Brand Name Garage Door Opener or Gate Receiver
Specication Notes
Pre-set Button
Number on
Remote
Number of
Button Presses
Genie® 315/390 MHz, Intellicode® I, 1995-current 1 1
Overhead Door® 315/390 MHz, CodeDodger® I, 1995-current 1 1
Chamberlain®
LiftMaster®
CraftsMan®
Purple Learn Button, Security +®, 2006-2014, 315 MHz 2 2
Orange/Red Learn Button, Security +®, 1996-2005, 390 MHz 3 3
Yellow Learn Button, Security +2.0®, 2011-current, 390 MHz 4 4
Green Learn Button, Billion Code®, 1993-1995, 390 MHz 5
Genie® 315/390 MHz, Intellicode® II, 2010-2011 6
Overhead Door® 315/390 MHz, CodeDodger® II, 2010-2011 6
Sommer® 310 MHz, Rolling Code 7
Linear® 318 MHz, Mega Code® 8
Wayne Dalton® 372.5 MHz, Rolling Code, 1999-current 9
Ryobi® 372.5 MHz, Rolling Code 10
Guardian® 303 MHz, Fixed Learn Code 11
Xtreme® brand 303 MHz, Fixed Learn Code 11
Marantec® 315 MHz, Fixed Learn Code 12
Chamberlain® 390 MHz, 9 Switch/3 Position Dip Switch
FAAC® 433.92 MHz, Rolling Code
Genie® 390 MHz, 9 & 12 Switch/2 Position Dip Switch, 1993-1995
Overhead Door® 390 MHz, 9 Switch/3 Position Dip Switch, 1993-1995
STEP 1 - FIND SPECIFICATIONS & LEARN BUTTON
1. Locate the brand and opener/receiver specications for your device by consulting the label on the
opener/receiver, the instruction manual, the current remote controls for the opener, or the original
manufacturer of the opener/receiver.
2. Find the LEARN/PROG button on your device - shape, color or name of this button could vary by
brand. For garage door openers, be sure to check under the light covers. For commercial or gate
openers, this button may be on the circuit board of the opener. In some cases, this button could
also be on an external receiver that is mounted on or nearby the product. Consult the devices
manual if needed.
STEP 3 - CHOOSE A PROGRAMMING OPTION
Review Chart A to nd your specications and available programming options. You can use any
combination of options available for your opener/specication combination to achieve your desired
button setup. Each button can be programmed individually to operate up to 4 dierent brands of
garage door openers and gate receivers.
Activation Tab: Pull tab to activate the remote.
STEP 2 - ACTIVATE REMOTE/BUTTON LAYOUT & LED
LED - The LED will light with each button press and
will also light in response to button presses during
dierent programming modes.
1 2
3 4
FIG. 1
OPTION 1: QUICK START METHOD
Reference FIG 1 to use any of these four manufacturer pre-sets to quickly program a button.
Button 1: Genie Intellicode 1 or Overhead Door CodeDodger I
Button 2: Chamberlain® with a PURPLE LEARN Button
Button 3: Chamberlain® with an ORANGE/RED LEARN Button
Button 4: Chamberlain® with a YELLOW LEARN Button* - Move directly to Chamberlain® Yellow
Learn Button instructions shown at right.
If using Button 1, 2 or 3:
1. On the garage door opener, press the LEARN button for 2-3 seconds and then release.
2. On the universal remote, press and release the pre-set button that corresponds with your opener
once every 2 seconds until the garage door opener operates. Programming is complete.
TIP: Allow the LED light on the universal transmitter to stop ashing before your next button press.
OPTION 2: LEARN METHOD
In this method, your universal remote will learn which specication you want it to work with.
1. Find and remember the required number of button presses in the LEARN METHOD column next to
your brands/specication in Chart A.
2. On the universal remote, press and hold down button #2. (Reference FIG. 1)
3. While still holding down button #2, press button #4 on the universal remote four times.
4. Release both buttons - the BLUE LED on the remote will begin ashing.
5. On the universal remote, press the button of your choice the required number of times
from Step 1. You will have 15 seconds to complete this task.
6. Wait the remainder of the 15 seconds - the BLUE LED will give a long blink and then go out.
*If using Chamberlain with Yellow LEARN button, please move directly to the Chamberlain®
YELLOW LEARN button instructions shown right. If using ANY OTHER brand/specication, please
continue below.
7. On the garage door opener, press the LEARN button for 2-3 seconds and then release.
8. On the universal remote, press and release the button you just programmed once every 2 seconds
until the garage door opener operates. Programming is complete.
TIP: Allow the LED light on the universal transmitter to stop ashing before your next button press.
OPTION 3: TEACH & PAIR
You must have an existing operational remote to use this method. The universal remote can learn from
an existing operational remote transmission and then be paired to the available brands/specication in
Chart A.
1. On the universal remote, press and hold down button #1.
2. While still holding down button #1, press button #2 on the universal remote four times.
3. Release both buttons - the WHITE LED on the remote will begin slowly ashing.
4. Place the existing, operational remote and the universal remote within 4” of each other.
5. Hold down the operational button from the original remote. Do not release until the new
universal remote blinks change from slow WHITE blinks to rapid BLUE blinks. You will have 20
seconds to complete your entry.
TIP: If the universal remote does not recognize the transmission, try dierent distances between 0”-4”
away from the side of the universal remote closest to button numbers 1 and 3.
6. Once the universal remote BLUE LED is blinking rapidly, press the button of choice on the universal
remote one time, slowly and deliberately. The BLUE LED will turn solid and then go out. *If using
Chamberlain with Yellow LEARN button, please move directly to the Chamberlain® YELLOW LEARN
button instructions below. If using ANY OTHER brand/specication, please continue below.
7. On the garage door opener, press the LEARN button for 2-3 seconds and then release.
8. On the universal remote, press and release the button you just programmed once every 2 seconds
until the garage door opener operates. This could take several presses. Programming is complete.
TIP: Allow the LED light on the universal transmitter to stop ashing before your next button press.
PRGM
SET
RADIO
SIGNAL
LEARN
CODE
CODE
LEARN
Gate
Recievers
EXAMPLES:
- TEACH & PAIR -
Must have existing operational
remote.
*For Marantec® openers, reference operator manual to program remotes to the operator head.
UNIVERSAL REMOTE
INSTRUCTIONS
PROGRAMMING ASSISTANCE:
If the opener does not activate after the steps shown, repeat steps or contact
Customer Care by website chat (www.geniecompany.com)
or by phone at: 1-800-354-3643 for programming assistance. You may also scan this
QR code for additional information and links.
For Patent Information: www.geniecompany.com/patent,
©2019 GMI Holdings DBA, The Genie Company
Genie® and Intellicode® are registered trademarks of The Genie Company. All other listed names and trademarks are the
property of their respective owners.
*For instructions on these Genie or Overhead Door® specications, visit
www.geniecompany.com/Documents/912DIPSWITCHES
For these dip switch instructions,
visit
www.geniecompany.com*