Operator’s Manual First Edition Sixth Printing Part No.
Operator's Manual First Edition • Sixth Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall be permitted to operate this machine. If you have any questions, call Genie Industries. Contents Page Safety ......................................................................... 1 Legend ........................................................................ 6 Pre-operation Inspection ...........
First Edition • Sixth Printing Operator's Manual Safety Rules Warning Failure to obey the instructions and safety rules in this manual may result in death or serious injury. Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations. Know and understand the safety rules before going on to the next section. 2 Always perform a pre-operation inspection. 3 Always perform the function tests prior to use.
Operator's Manual First Edition • Sixth Printing SAFETY RULES Do not place ladders or scaffolding against any part of the machine. Fall Hazards Do not use as a personnel lifting platform or step. Do not operate the machine unless the wheel / leg / caster configuration is properly installed. Do not stand or sit on the forks, load platform or boom. Prior to use, check the work area for drop-offs, holes, bumps, debris, unstable or slippery surfaces or other possible hazardous conditions.
First Edition • Sixth Printing Operator's Manual SAFETY RULES Electrocution Hazards Improper Use Hazard This machine is not electrically insulated and will not provide protection from contact with or proximity to electrical current. Never leave a machine unattended with a load. Unauthorized personnel may attempt to operate the machine without proper instruction, creating an unsafe condition.
Operator's Manual First Edition • Sixth Printing SAFETY RULES Ladder Safety Electric Winch Safety Fall Hazards Electrocution Hazard Do not use the ladder as scaffolding. Do not operate the DC battery charger unless using a 3-wire grounded extension cord connected to a grounded AC circit. Do not alter or disable the 3-wire grounded plugs. Do not sit on the ladder. Do not over reach. Keep your body centered between both side rails. Tip-over Hazards Do not use the top rung as a step.
First Edition • Sixth Printing Operator's Manual SAFETY RULES Decal Legend Explosion Hazards Batteries emit explosive gas. Keep sparks, flames and lighted tobacco away from the battery. Genie product decals use symbols, color coding and signal words to identify the following: Charge the battery in a well-ventilated area. Do not disconnect the charger DC output wires from the battery when the charger is on. Safety alert symbol—used to alert personnel to potential personal injury hazards.
Operator's Manual 6 First Edition • Sixth Printing Genie Lift Part No.
First Edition • Sixth Printing Operator's Manual LEGEND Models with electric winch option Straddle Base with 4 Point Casters 24 Brake (option) 25 Fork lock pin 26 Winch mounting bracket 27 Winch 28 Boom (option) 29 Load platform (option) 30 Electric winch battery Part No.
Operator's Manual First Edition • Sixth Printing Pre-operation Inspection Fundamentals The pre-operation inspection is a visual inspection performed by the operator prior to each work shift. This inspection is designed to discover if anything is apparently wrong with a machine before the operator tests it. Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection.
First Edition • Sixth Printing Operator's Manual PRE-OPERATION INSPECTION Pre-operation Inspection o Be sure that the operator’s manual is complete, legible and available for reference. Check the entire machine for: o Be sure that all decals are legible and in place. See Decals section.
Operator's Manual First Edition • Sixth Printing Function Tests Fundamentals The function tests are designed to discover any malfunctions before the machine is put into service. The operator must follow the step-by-step instructions to test all machine functions. Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. 3 Always perform function tests prior to use.
First Edition • Sixth Printing Operator's Manual FUNCTION TESTS Function Tests Load Platform 1 Select a test area that is firm, level and free of obstructions. 1 Lay the load platform onto the forks. Setup 1 Tilt the machine back. 2 Slide each fork onto the carriage and secure it with the fork lock pins. 3 Slide each leg into a base socket until the leg lock pin snaps into the leg.
Operator's Manual First Edition • Sixth Printing FUNCTION TESTS Test the Brake Operation (if equipped) Test Electric Winch Operation (if equipped) 1 Press down on the foot pedal to lock the brake. Note: The Genie Lift 4 does not have an inner frame. 2 Push the machine. Result: The wheels should not roll. 1 Connect the battery pack. 2 Pull out the red Emergency Stop button to the on position. 3 Pull up on the foot pedal to release the brake. 4 Push the machine.
First Edition • Sixth Printing Operator's Manual Workplace Inspection Be aware of and avoid the following hazardous situations: · drop-offs or holes · bumps and floor obstructions · debris · overhead obstructions and high voltage conductors Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations.
Operator's Manual First Edition • Sixth Printing Operating Instructions Setup Select an area that is firm, level and free of obstructions. Follow the Setup procedures in the Function Tests section. Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. Raising and Lowering Load Manual Winch 1 Center the load on the forks or load platform. 2 Raise the load by firmly grasping the winch handle and rotating it clockwise.
First Edition • Sixth Printing Operator's Manual OPERATING INSTRUCTIONS Moving Machine with a Load After Each Use It is best to move the machine on the work site with no load. Moving a raised load should be restricted to positioning for loading and unloading. If it is necessary to move the machine with a raised load, understand and obey the following safety rules: To prepare the machine for storage, remove the forks and legs and reverse the winch handle. Refer to the Setup procedure.
Operator's Manual First Edition • Sixth Printing OPERATING INSTRUCTIONS 9 Charger models equipped with manual/auto selector switch: If the ampere meter indicates that the battery is not being charged, set the power switch to the MANUAL position until the ampere meter begins to move up the scale. Then set the power switch to the AUTO position. Battery and Charger Instructions Observe and Obey: 10 The charger will turn off automatically when the battery is fully charged.
First Edition • Sixth Printing Operator's Manual OPERATING INSTRUCTIONS Lifting Instructions The number of people required to load and unload a machine is dependent on a number of factors, including but not limited to: · the physical condition, strength and disabilities or prior injuries of the people involved Transport Instructions · the vertical and horizontal distances the machine has to be moved Observe and Obey: Be sure the vehicle capacity and loading surfaces are sufficient to support the machi
Operator's Manual First Edition • Sixth Printing Load Capacity Charts Forks Load Positioning Instructions 1 Determine the weight of the load and the location of its load center. 2 Measure to the load center from the side of the load that will be closest to the carriage. Observe and Obey: Failure to properly position the load may result in death or serious injury. 3 Refer to the chart on the next page to determine if the machine is capable of lifting the weight at the location on the forks.
First Edition • Sixth Printing Operator's Manual LOAD CAPACITY CHARTS Maximum Load Centers Forks Load Capacity Chart inches cm 12 30 14 35 GL-4 lbs kg GL-8 lbs kg lbs kg lbs kg 500 227 400 181 350 159 500 227 400 181 350 159 350 159 350 159 (measure from front of carriage) Model GL-10 GL-12 Forks: 14 in 35 cm Load Platform: 14 in 35 cm Boom: 20 in 51 cm Boom Load Positioning Instructions 1 Determine the weight of the load and the location of its load center.
Operator's Manual First Edition • Sixth Printing 35574 35567 43022 43021 52982 35577 or 35578 or 35579 35577 or 35578 or 35579 37120 37111 82959 33468 97529 37111 37084 37049 35575 20 Genie Lift Part No.
First Edition • Sixth Printing 52982 Operator's Manual 97539 97536 82487 82487 82481 97511 or 97512 or 97513 97511 or 97512 or 97513 97533 97540 97539 97532 97540 82962 Serial Plate 82487 82487 97510 Part No.
Operator's Manual First Edition • Sixth Printing Specifications Model GL-4 GL-8 GL-10 GL-12 Height, maximum lift Forks up 5 ft 11 in 1.8 m 10 ft 1/2 in 3.1 m 11 ft 8 in 3.6 m 13 ft 91/2 in 4.2 m Height, maximum lift Forks down 4 ft 11/2 in 1.2 m 8 ft 3 in 2.5 m 9 ft 101/2 in 3m 12 ft 3.7 m Height, minimum lift Forks down 31/2 in 8.9 cm 31/2 in 8.9 cm 2 in 5.1 cm 2 in 5.1 cm Lift capacity at 12 in / 30.
First Edition • Sixth Printing Operator's Manual SPECIFICATIONS Model Forks Length Width Load Platform Length Width GL-4 GL-8 GL-10 GL-12 221/2 in 57.2 cm 201/2 in 52.1 cm 221/2 in 57.2 cm 201/2 in 52.1 cm 221/2 in 57.2 cm 201/2 in 52.1 cm 221/2 in 57.2 cm 201/2 in 52.1 cm 23 in 58.4 cm 22 in 55.9 cm 23 in 58.4 cm 22 in 55.9 cm 23 in 58.4 cm 22 in 55.9 cm 23 in 58.4 cm 22 in 55.
Phone 425.881.1800 Toll Free USA and Canada 800.536.1800 Fax 425.883.3475 Genie Australia Pty Ltd. Phone +61 7 3375 1660 Fax +61 7 3375 1002 Genie Scandinavia Phone +46 31 575100 Fax +46 31 579020 Genie France Phone +33 (0)2 37 26 09 99 Fax +33 (0)2 37 26 09 98 Genie Iberica Phone +34 93 579 5042 Fax +34 93 579 5059 Genie Germany Phone +49 (0)4202 88520 Fax +49 (0)4202 8852-20 Genie U.K.