il Check where power head ofyour your ceiling new unit will the be mounted. Plan how you will be mounting the power head. It is possible that ceiling joists may not be in the position needed with respect to the garage door operator. It may be necessary to add an additional bracket and fasteners (not included with your new door operator kit). Check the door wall operator's directly above garage door. The headerthebracket must be securely fastened to this wall.
® @ TYPICAL SUPPORT BRACKET ADDED HEADER BRACKET MOUNTING BOARD BRACES 48" POWER TO 120V GROUNDED OUTLET EXTENSION OR TORSION SPRING' ® SECTmONAL DOOR I-PmECE DOOR
SECTION ......................................... PRE-INSTALLATION CHECKS .......................... OPERATORFEATURES ................................. SAFETYFEATURES .................................... TOOLS RECOMMENDED ................................ PARTS IDENTIFICATION .............................. SAFETY INFORMATION ................................. OPERATOR ............................................. 1 ASSEMBLY .................................... 2 INSTALLATION ................................
Ratchet Pencil Drill 7/16"and 9/16" Sockets Step ladder Adjustable wrench Phillipsscrewdriver Wire strippers % © r_ 5/32" Drill Bit Carpenter's level Tape measure ii ,&WARNING oRI #6 x 1-1t4" Pan (32) Head Phillips Screw Wall console @ Single-button remote control Safety Brochure Multi-button remote control @ Entrapment Warning Label Q @ #10-16 x 1-1t4" Machine Screw Wire lnsu_taple #6 x 1-1/4" Pan Head Phillips Screw Wall button [9] Bolt - 1/4"-20 x 5/8" Source STB (Red LED) S
/ \ @ \
ItemPartName 10 11 12 13 14 15 16 17 18 !0 !2 !3 !4 !5 !6 !7 !8 !9 30 31 32 33 34 35 36 37 38 39 _0 H $2 N _6 $7 $8 NumberRequired 1 pc,rail 3 pc,rail Power headassembly (box) 1 1 Railassembly (1-piece#box) 1 Rail(1-piece)(box) 1 Railassembly (3-piece)(items 5,6,7)(box) 1 Firstrailsection(box) 1 Middle railsection (box) 1 Endrailsection (box) 1 Railclamp (bluebag) 4 1/4"-20 x 5/8"hexheadbolt(blueba@) 4 12 1/4"-20 hexflangenut(bluebag) 4 12 Carriage assembly (box) 1 1 Railstrap(bluebag) 1 1 LimitswitchOPEN
1 1. Identify the rai! sections (Fig. 1-1). • First rail section (attaches to power head). - 2 holes each end. - Half-circle notch 1 end. - Motor end has no notch. • Middle rail section. - 2 holes & half-circle notch each end. • End rail section (attaches to door). - Has 4 holes on door end. 2. Arrange arrows on rail sections. • Sections have arrows stamped into one side. - Aim all arrows toward door. (Fig. 1-2) ex_ensFon on an _ foot h_yh doox_ _f_;_ t_f:_ the 3. Attach rail clamps to rail (Fig. 1-3).
5. Slip carriage into carriage slot of rail. • Flip the rail assembly up side down. • Place emergency release lever in "release" position (See below). - Check arrow on the side of carriage points toward door end of rail. - Slide carriage into rail at power head end (Fig. 1-5). - Flip rail assembly right-side up. 6. Attach rail to power head. * Place rail in front of power head with rail strap at opposite end. * Support door end of rail (rail strap) at about same height as power head.
g. Attach limit switches. 2 switches included, "CLOSE" limit switch (brown wire) and "OPEN" limit switch (white wire) (Fig. 1-10). • Turn set screws (39) into threaded holes, just enough so screw stays in place. (Fig. 1-10). [39]#8_32 xi,, Point arrow on top "CLOSE" limit switch toward door end of rail. - Place "CLOSE" limit switch (Brown wire) on rail about 12" from rail strap (Fig. 1-11). - Gently tighten set screw enough to keep switch from moving.
2 iMPORTANT Toreduce theriskofsevere injuryordeath: 1. READ AND FOLLOW ALL SAFETY, INSTALLATIONAND OPERATION INSTRUCTIONS. If you have questions or do not understand an instruction, call The Genie Company or an authorized Genie Dealer. 2. Do Not install operator on an improperly balanced door. An improperly balanced door could cause severe injury.
NO7_iF; f he_-_oq;)b;"scke ocs_Fo_*_needs o be _;_bove hesde;' fb;' !is_'_!_!_i'e ch::_o openh, W you £;,oud seco_,e@ _sched i'@s_one;'s no h_c/ @d} _;_c;'oss w_d/suo%; o_ eF he, sM_, of;/o mu£ £_ s f?Ycien (Fig. 2-4) 2. Mounting the header bracket. seye_x,_ w_ys, mehod _ I M pmM_,"_d f_ poss b _ bec_se of _d@d s_,ng_h ore;' o_he me hodxs (Fig, 2-5) • Hold header bracket against wall (Fig. 2-5). - Place left edge on vertical line. - Bottom edge on final height line. • Mark screw hole locations on wall.
1. Getting Started. • Positionrail/powerheadassembly(Fig.2-7). - Railstrapleaningonwallnexttoheaderbracket. -Place materialon floorunderpowerheadto protectfromscratching.(Abox,stool,or similar devicemaybe neededto cleara torsion spring,as shown.) 2, Mountingthe assembly. • Attachrail strapto headerbracketusingnut (47) (Fig.2-7inset). FINGERTIGHTONLY. [47] 5/16"-18 HEADER BRACKET J DOOR 90 ° • Support power head on step-ladder.
OPEH YELLOW RTS BAG 1. Attach the arms. • Fasten curved door arm to door bracket using clevis pin (24) and cotter pin (25) (Fig. 2-10). • Straight arm to carriage using clevis pin (24) and cotter pin (25) (Fig. 2-10). [24] 2. Connecting [25] the arms. • Slide carriage back and forth to adjust arm length. -Overlap arms as much as possible. - Make overall length as short as possible. • Fasten arms together using 2 bolts (27) and nuts (28) (Fig. 2-10).
3 h_O_TE"%h.... 1. Mounting brackets. • Mark both sides of garage door frame or wall 5" above floor. (Fig. 3-1). • Hold bracket against door frame or wall. - Check if brackets extend out from wall far enough, so tongue of bracket is beyond door, tracks or any door hardware. -if not: a. "STB" bracket extensions are available at local dealer. b. Blocks of wood, etc. may be substituted for extensions. • Center bracket on your mark (Fig. 3-2). • Fasten each with 2 screws (44) (Fig. 3-2). [44] 2.
3. Wiring (cont'). • Securely fasten wires to wall as you go. -Use insulated staples (included). [30] -Staples should be snug only. • Make wire attachments at "STB's." -Splitting and stripping wire ends to be connected as shown (Fig. 3-6). -Loosen terminal screws. -Insert wire under flat plate and tighten screw. It does not matter which wire, white or striped, goes on which terminal (Fig. 3-7). • Make wire attachments at power head. -"STB's" are connected to terminals #2 and #3 on power head (Fig.
4 1. Finding the mounting location. • Pick a convenient location for mounting wall control. -Location you choose should be in direct sight of door. -It should be at least 5' above floor to prevent small children from operating door. -It must be away from any moving parts. (You should not be able to reach the door while standing at wall control.) 2. Wiring. • Run wire from power head to wall control. • Securely fasten to ceiling using insulated staples provided. • Split and strip ends of wire (Fig. 4-5).
5 1. Plug the operator electrical outlet. 2. Check into a properly grounded Safe-T-Beam® alignment (Fig. 6-3). 1. instructions for electrician. • Remove power from circuit. • Remove motor cover (Fig. 6-1). -Removing hex head screw located in center on bottom of cover. -Slide cover down and off. • Remove and throw away existing power cord. • Remove 7/8" knockout plug (Fig. 6-2). -install a suitable entrance bushing. • Connect permanent wiring to power head.
6 NO'}q_:;: ©u_<;gopen_}_®_" cl,,,c hW hhyfouc'® _j ,fsm en< _he _' o_oY p
The force adjustments and limit switch settings MUST BE COMPLETED before testing contact reverse. 1. Testing. • Open garage door using wall control. - Place a 2" x 4" board (laid flat) under center of garage door opening (Fig. 7-5). -Close door using wall control. • When door hits board, it must stop and reverse (within 2 seconds) to open position. 2. Adjustment. • Door does not properly reverse. -Check to see if door is at "close" limit. -It should not have reached limit switch before hitting board.
1. Programming. • Foreachbutton. -Program eachbuttonseparately. - Followsinglebuttonremoteprocedure (previouspage)for eachbutton. 2. Operating. • Sameas singlebuttonremote. 1. Clearmemory. • Pressandholdlearncodebutton(on power head) for 10 seconds or until Indicator LED goes out. • Program remaining or new remote controls as done previously. Your door operator will no longer recognize any signal received from the missing remote control, or any other which has not been reprogrammed. 1.
iMPORTANT SAFETY iNSTRUCTiONS Toreducethe riskof severeinjuryor death: !! . READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate or play with the door controls. Keep the remote control away from children. 3. Always keep the moving door in sight and away from people and objects until the door is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR. . NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR. 5. Test operator monthly.
Usewall controlsuppliedwithoperator.Any otherwall controlcan cause the operatorto operateunexpectedlyand lightnot to work. Operator does not run from wall control. Door operator starts for no reason. • Checklock switchon wall console. • Checkpowersource. - Pluga lampinto outletusedfor power headIf lampworks,powersourceis OK. - If not,checkfuse or circuitbreaker. • Poweris OK. - Checkconnectionsat powerhead terminals. - Checkconnectionsat wall control. • Checkwires to ensuretheyare not cut.
/ !1 TRANSMITTER COMPLIANCE STATEMENT Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture. No warranty is made that they comply with all legal requirements of any other jurisdiction. If transmitters are to be used in another country, the importer must determine compliance with any local laws and regulations which may differ from United States and Canadian requirements prior to use.
GEI IE: Prices on reverse Precio en dorso Prix sur oppose Garage Door Operator Accessories Accesorios para abridores de garajes Accessoires pour ouvre-porte de garage AVAILABLE AT YOUR LOCAL GENIE ¢ DISTRIBUTOR II (GIT-1)1-ButtonRemoteControlwithIntellicode®. - Allowsremoteoperation ofonegaragedoor. Controladorremotode uricbotchcon Intellicode®.Proporcionar operacion remotodeunopuertadelgaraje. Telecommande de un boutonavecIntellicode®. - Permettre operation elogindeunportedegarage.
Garage Door Operator Accessories Order Form Formulario de pedido de accesorios para abridores de puertas de garaje Formulaire de commande des accessoires pour ouvre-porte de garage MODEL MODELO MODELE II DESCRIPTION DESCRIPCION DESCRIPTION Deluxe Remote Control withtntellicode ® GIT-I i Controlador remoto delujoconIntellicode ® i Tel6commande deluxeavecIntellicode ® PRODUCT CODE PRICE (US$)* QTY, TOTAL CODIGO PRECIO*CANTIDAD TOTAL CODE DUPRODUITPRIX($US)* QTE TOTAL 33069R $34.
The Genie Company ProfessionalAccess Systems LiMiTED WARRANTY What is covered:Any defect in materialand productworkmanshipfrom personal, normal household use inaccordance with the Owner's Manual. For how long: H2000C-1 Series - 3 years on Motor,and 1 year on all other parts. 350L- 1 Series - 3 years on Motor,and 1 year on all other parts. 350L- 1XSeries - 5 years on Motor, and 2 year on all other parts. 350L - 2 Series - 5 years on Motor,and 2 years on all other parts.
