Operator’s Manual First Edition Eighth Printing Part No.
Operator's Manual First Edition • Eighth Printing Important Read, understand and obey these safety rules and operating instructions before operating this machine. Only trained and authorized personnel shall be permitted to operate this machine. This manual should be considered a permanent part of your machine and should remain with the machine at all times. If you have any questions, call Genie Industries. Contents Page Safety ........................................................................
First Edition • Eighth Printing Operator's Manual Safety Rules Warning Failure to obey the instructions and safety rules in this manual may result in death or serious injury. Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations. Know and understand the safety rules before going on to the next section. 2 Always perform a pre-operation inspection. 3 Always perform the function tests prior to use.
Operator's Manual First Edition • Eighth Printing SAFETY RULES Fall Hazards Do not use as a personnel lifting platform or step. Do not stand on the load handling attachments. Do not raise the load unless the load handling attachment is properly secured to the machine. Do not use blocks to level the machine. Do not climb on the mast.
First Edition • Eighth Printing Operator's Manual SAFETY RULES Do not place ladders or scaffolding against any part of the machine. Electrocution Hazards This machine is not electrically insulated and will not provide protection from contact with or proximity to electrical current. Do not use the machine on a moving or mobile surface or vehicle. Collision Hazards Check the work area for overhead obstructions or other possible hazards.
Operator's Manual First Edition • Eighth Printing SAFETY RULES Crushing Hazards Damaged Machine Hazards Keep hands and fingers away from folding legs and other potential pinch points. Do not use a damaged or malfunctioning machine. Do not raise if the load is not properly centered on the load handling attachment. Do not use a machine with a worn, frayed, kinked or damaged cable. Do not raise unless the load is properly secured to the load handling attachment.
First Edition • Eighth Printing Operator's Manual SAFETY RULES Decal Legend Genie product decals use symbols, color coding and signal words to identify the following: Safety alert symbol—used to alert personnel to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Red—used to indicate the presence of an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Operator's Manual First Edition • Eighth Printing Legend 1 2 3 4 5 6 7 8 9 10 25 11 7 7 24 23 12 22 21 7 20 13 19 18 17 16 15 14 1 Winch 10 Boom 19 Stabilizer caster 2 Lifting bracket 11 Shackle 20 Base 3 Cable 12 Fork extension 21 Stabilizer brace 4 Mast 13 Pipe cradle 5 Carriage 14 Leg swivel caster 22 Base swivel/lock caster with brake 6 Standard forks 15 Leg 23 Transport wheel 7 Load handling attachment retaining pin 16 Hold-down bar 24 Mast brace 17 L
First Edition • Eighth Printing Operator's Manual Pre-operation Inspection Fundamentals The pre-operation inspection is a visual inspection performed by the operator prior to each work shift. This inspection is designed to discover if anything is apparently wrong with a machine before the operator tests it. Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection.
Operator's Manual First Edition • Eighth Printing PRE-OPERATION INSPECTION Pre-operation Inspection R Be sure that the operator’s manual is complete, legible and in the storage container located on the machine. R Be sure that all decals are legible and in place. See Decals section.
First Edition • Eighth Printing Operator's Manual Function Tests Fundamentals The function tests are designed to discover any malfunctions before the machine is put into service. The operator must follow the step-by-step instructions to test all machine functions. Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. A malfunctioning machine must never be used.
Operator's Manual First Edition • Eighth Printing FUNCTION TESTS Load Handling Attachments Function Tests 1 Select a test area that is firm, level and free of obstructions. Setup Standard Forks and Standard Fork Options 1 Place the forks inside the carriage. 2 Insert the retaining pin. Machines Without Stabilizers 1 Remove the leg retainer pin and lower the leg to the down position. Insert the pin through the leg and base.
First Edition • Eighth Printing Operator's Manual FUNCTION TESTS Adjustable Fork and Adjustable Fork Options Fork Extension 1 Place the forks inside the carriage. 1 Slide each extension tube onto the fork. 2 Insert the retaining pin. 2 Adjust to the desired position and insert the retaining pins. Standard Boom 1 Place the boom inside the carriage. 3 Adjust the forks to the desired width and be sure the snap pins are properly inserted. 2 Insert the retaining pin.
Operator's Manual First Edition • Eighth Printing FUNCTION TESTS Test One-Speed Winch Operation Test Two-Speed Winch Operation 1 Install a load handling attachment. 1 Install a load handling attachment. 2 Raise the carriage by firmly grasping the winch handles and rotating them towards the mast. Result: The winch should operate smoothly, free of hesitation or binding. 2 Shift the winch to the slow speed.
First Edition • Eighth Printing Operator's Manual Workplace Inspection Be aware of and avoid the following hazardous situations: · drop-offs or holes · bumps and floor obstructions · debris Do Not Operate Unless: · overhead obstructions and high voltage conductors You learn and practice the principles of safe machine operation contained in this operator's manual. · hazardous locations 1 Avoid hazardous situations. · unstable or slippery surfaces 2 Always perform a pre-operation inspection.
Operator's Manual First Edition • Eighth Printing Operating Instructions Fundamentals The Operating Instructions section provides instructions for each aspect of machine operation. It is the operator's responsibility to follow all the safety rules and instructions in the operator's manual. Do Not Operate Unless: Using the machine for anything other than lifting material is unsafe. You learn and practice the principles of safe machine operation contained in this operator's manual.
First Edition • Eighth Printing Operator's Manual OPERATING INSTRUCTIONS Setup Moving Machine with a Load Select an area that is firm, level and free of obstructions. It is best to move the machine on the worksite with no load. Moving a raised load should be restricted to positioning for loading and unloading. If it is necessary to move the machine with a raised load, understand and obey the following safety rules: Follow the Setup procedures in the Function Tests section.
Operator's Manual First Edition • Eighth Printing Load Capacity Charts Forks Load Positioning Instructions 1 Determine the weight of the load and the location of its load center. 2 Measure to the load center from the side of the load that will be closest to the carriage. Observe and Obey: Failure to properly position the load may result in death or serious injury. Verify that the load you wish to raise does not exceed the maximum load for your load center. See Load Capacity Chart section.
First Edition • Eighth Printing Operator's Manual LOAD CAPACITY CHARTS Boom Maximum Load Centers (measure from the front of the carriage) Load Positioning Instructions 1 Determine the weight of the load and the location of its load center. 2 Refer to the chart below to determine if the machine is capable of lifting the weight at the location on the boom. 3 Secure the load to the lifting shackle on the boom.
Operator's Manual First Edition • Eighth Printing Decals Inspection for Decals with Words Determine whether the decals on your machine have words or symbols. Use the appropriate inspection to verify that all decals are legible and in place. Part No.
First Edition • Eighth Printing Operator's Manual DECALS 32687 33468 52984 33468 32775 Shading indicates decal is on the other side of the machine. 32714 97547 52984 97529 33468 40513 or 33454 Serial Plate 32716 33468 32938 32885 32939 32770 32717 52675 31072 52992 or 52993 or 52994 or 52995 52992 or 52993 or 52994 or 52995 Serial Plate Part No.
Operator's Manual First Edition • Eighth Printing DECALS Inspection for Decals with Symbols Determine whether the decals on your machine have words or symbols. Use the appropriate inspection to verify that all decals are legible and in place. Part No. Description Quantity Part No.
First Edition • Eighth Printing Operator's Manual DECALS Shading indicates decal is on the other side of the machine. Part No.
Operator's Manual First Edition • Eighth Printing Transport and Lifting Instructions 5 Lock the rear base casters. Observe and Obey: The transport vehicle must be parked on a level surface. 6 Place the machine against the vehicle. Use proper lifting techniques to load the machine into the transport vehicle. Be sure to check that the carriage is locked in the lowered position. The transport vehicle must be secured to prevent rolling while the machine is being loaded.
First Edition • Eighth Printing Operator's Manual Specifications Model SLC-6 SLC-12 SLC-18 SLC-24 86 in 2.2 m 86 in 2.2 m 86 in 2.2 m 86 in 2.2 m 311/2 in 80 cm 311/2 in 80 cm 311/2 in 80 cm 311/2 in 80 cm 66 in 1.7 m 66 in 1.7 m 66 in 1.7 m 66 in 1.7 m 34 in 86.4 cm 34 in 86.4 cm 34 in 86.4 cm 34 in 86.4 cm 59 in 1.5 m 63 in 1.6 m 73 in 1.8 m 81 in 2m 2 in 50.8 mm 2 in 50.8 mm 2 in 50.8 mm 2 in 50.
Genie North America Phone 425.881.1800 Toll Free USA and Canada 800.536.1800 Fax 425.883.3475 Genie Australia Pty Ltd. Phone +61 7 3375 1660 Fax +61 7 3375 1002 Genie Scandinavia Phone +46 31 575100 Fax +46 31 579020 Genie France Phone +33 (0)2 37 26 09 99 Fax +33 (0)2 37 26 09 98 Genie Iberica Phone +34 93 579 5042 Fax +34 93 579 5059 Genie Germany Phone +49 (0)4202 88520 Fax +49 (0)4202 8852-20 Genie U.K.
