® A Division of Cisco Systems, Inc. 2.4 GHz Wireless-B 802.11b Broadband Router WIRELESS Model No.
Wireless-B Broadband Router Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2004 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
Wireless-B Broadband Router Table of Contents Chapter 1: Introduction 1 Welcome What’s in this Guide? 1 2 Chapter 2: Planning your Wireless Network Network Topology Roaming Network Layout Chapter 3: Getting to Know the Wireless-B Broadband Router The Back Panel The Front Panel Chapter 4: Connecting the Wireless-B Broadband Router Hardware Installation Chapter 5: Configuring the Wireless-B Broadband Router Overview The Setup Tab - Basic Setup The Setup Tab - MAC Address Clone The Setup Tab - Advanced
Wireless-B Broadband Router Appendix A:Troubleshooting Common Problems and Solutions Frequently Asked Questions Appendix B: Wireless Security Security Precautions Security Threats Facing Wireless Networks 31 31 38 45 45 45 Appendix C: Upgrading Firmware 48 Appendix D: Windows Help 49 Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter 50 Windows 98 or Me Instructions Windows 2000 or XP Instructions For the Router’s Web-based Utility 50 50 51 Appendix F: Glossary Appendix G: S
Wireless-B Broadband Router List of Figures Figure 3-1: The Broadband Router’s Back Panel Figure 3-2: The Broadband Router’s Front Panel Figure 4-1: Connecting Your Internet Connection Figure 4-2: Connecting Your Network Devices Figure 4-3: Connecting the Power Figure 5-1: Password Screen Figure 5-2: Setup Tab - Basic Setup Figure 5-3: DHCP Connection Type Figure 5-4: Static IP Connection Type Figure 5-5: PPPoE Connection Type Figure 5-6: RAS Connection Type Figure 5-7: PPTP Connection Type Figure 5-8: Hea
Wireless-B Broadband Router Figure 5-26: Applications and Gaming - UPnP Forwarding Figure 5-27: Applications and Gaming - DMZ Figure 5-28: Administration Tab - Management Figure 5-29: Backup & Restore Figure 5-30: Administration Tab - Log Figure 5-31: Log Table Figure 5-32: Administration Tab - Firmware Upgrade Figure 5-33: Administration Tab - Factory Defaults Figure 5-34: Status Tab - Router Figure 5-35: Status Tab - Local Network Figure 5-36: Status Tab - DHCP Active IP Table Figure C-1: Upgrade Firmwar
Wireless-B Broadband Router Chapter 1: Introduction Welcome Thank you for choosing the Linksys Wireless-B Broadband Router. Think of the Linksys Wireless-B Broadband Router as a kind of "splitter" for your Internet connection. Just connect your DSL or Cable Modem to the Router, and all the computers in your household can share the Internet -- all at the same time.
Wireless-B Broadband Router What’s in this Guide? This user guide covers the steps for setting up and using the Wireless-B Media Adapter. • Chapter 1: Introduction This chapter describes the Adapter’s applications and this User Guide. • Chapter 2: Planning your Wireless Network This chapter describes the basics of wireless networking. • Chapter 3: Getting to Know the Wireless-B Broadband Router This chapter describes the physical features of the Router.
Wireless-B Broadband Router • Appendix G: Specifications This appendix provides the technical specifications for the Router. • Appendix H: Warranty Information This appendix supplies the warranty information for the Router.. • Appendix I: Regulatory Information This appendix supplies the regulatory information regarding the Router.. • Appendix J: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Wireless-B Broadband Router Chapter 2: Planning your Wireless Network Network Topology A wireless LAN is a group of computers, each equipped with one Linksys wireless adapter. Computers in a wireless LAN must be configured to share the same radio channel. The Linksys wireless adapters provide access to a wired LAN for wireless workstations. An integrated wireless and wired LAN is called an infrastructure configuration.
Wireless-B Broadband Router Network Layout The Wireless-B Broadband Router is compatible with all 802.11b adapters, such as the PC Card (WPC11) for your laptop computers, PCI Card (WMP11) for your desktop PC, and USB Adapter (WUSB11) for when you want to enjoy USB connectivity. The Router will also communicate with the wireless PrintServer (WPS11) and bridges (WET11).
Wireless-B Broadband Router Chapter 3: Getting to Know the Wireless-B Broadband Router The Back Panel The Broadband Router's ports, where the cables are connected, are located on the back panel. Figure 3-1: The Broadband Router’s Back Panel Reset Button There are two ways to reset the Broadband Router's factory defaults. Either press the Reset Button, for approximately ten seconds, or restore the defaults from the Password tab in the Web-based Utility.
Wireless-B Broadband Router The Front Panel The Router's LEDs, where information about network activity is displayed, are located on the front panel. Figure 3-2: The Broadband Router’s Front Panel Power Green. The Power LED lights up and will stay on while the Router is powered on. When the Router goes through its self-diagnosis mode during every boot-up, this LED will blink, then stop when the diagnosis is complete. Wireless-B Green. The Wireless-B LED lights up when there is a wireless connection.
Wireless-B Broadband Router Chapter 4: Connecting the Wireless-B Broadband Router Hardware Installation 1. Locate an optimum location for the Broadband Router. The best place for the Broadband Router is usually at the center of your wireless network, with line of sight to all of your mobile stations. 2. Fix the direction of the antenna. Try to place it in a position that will best cover your wireless network. Normally, the higher you place the antenna, the better the performance will be.
Wireless-B Broadband Router Chapter 5: Configuring the Wireless-B Broadband Router Overview The Broadband Router has been designed to be functional right out of the box with the default settings in the Setup Wizard. However, if you’d like to change these settings, use the Router’s web-based utility. This chapter will describe each web page in the Utility and each page’s key functions. The utility can be accessed via your web browser through use of a computer connected to the Router.
Wireless-B Broadband Router The Setup Tab - Basic Setup The first screen that appears displays the Setup tab. This allows you to change the Broadband Router's general settings. Change these settings as described here and click the Save Settings button to apply your changes or Cancel Changes to cancel your changes. Internet Setup The Internet Setup section configures the Broadband Router to your Internet connection. Most of this information can be obtained through your ISP.
Wireless-B Broadband Router button. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. subnet mask: An address code that determines the size of the network. Keep Alive:Redial Period. If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, click the radio button next to Keep Alive.
Wireless-B Broadband Router Optional Settings (Required by some ISPs) Some of these settings may be required by your ISP. Verify with your ISP before making any changes. Host Name/Domain Name. These fields allow you to supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name.
Wireless-B Broadband Router Network Setup Router IP. The values for the Router’s Local IP Address and Subnet Mask are shown here. In most cases, keeping the default values will work. Local IP Address. The default value is 192.168.1.1. Subnet Mask. The default value is 255.255.255.0. Network Address Server Settings (DHCP). A Dynamic Host Configuration Protocol (DHCP) server automatically assigns an IP address to each PC on your network for you.
Wireless-B Broadband Router The Setup Tab - MAC Address Clone A MAC address is a 12-digit code assigned to a unique piece of hardware for identification. Some ISPs will require you to register a MAC address in order to access the Internet. If you do not wish to re-register the MAC address with your ISP, you may assign the MAC address you have currently registered with your ISP to the Router with the MAC Address Clone feature. MAC Clone Service.
Wireless-B Broadband Router The Setup Tab - Advanced Routing This tab is used to set up the Router’s advanced functions. Dynamic Routing will automatically adjust how packets travel on your network. Static Routing sets up a fixed route to another network destination. NAT. Network Address Translation (NAT) technology translates IP addresses of a local area network to a different IP address for the Internet. To enable the NAT function, click Enable. Dynamic Routing.
Wireless-B Broadband Router Click the Show Routing Table button to view the Static Routes you’ve already set up. For each route, the Destination IP address, Subnet Mask, Gateway, and Interface are displayed . Click the Refresh button to update the information. Change these settings as described here and click the Save Settings button to apply your changes or Cancel Changes to cancel your changes. The Wireless Tab - Basic Wireless Settings The basic settings for wireless networking are set on this screen.
Wireless-B Broadband Router The Wireless Tab - Wireless Security The Wireless Security settings configure the security of your wireless network. Click the radio button next to Enable to enable Wireless Security before choosing your options. Click the radio button next to Disable if you need to disable Wireless Security. There are four wireless security mode options supported by the Router, WPA, RADIUS, and WEP. These four are briefly discussed here. WPA Pre-Shared Key.
Wireless-B Broadband Router • Default Key. Select which WEP key (1-4) will be used when the Gateway sends data. Make sure that the receiving device (wireless client) is using the same key. • WEP Keys 1-4. WEP keys enable you to create an encryption scheme for wireless network transmissions. If you are not using a Passphrase, then manually enter a set of values. (Do not leave a key field blank, and do not enter all zeroes; they are not valid key values.
Wireless-B Broadband Router The Wireless Tab - Wireless Network Access Wireless network access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s radius. Wireless Network Access. If you select Allow All, all computers will be allowed access to the wireless network. To restrict access to the network, select Restrict Access. Click the Wireless Client MAC Address button, and the Wireless Client MAC list will appear.
Wireless-B Broadband Router The Wireless Tab - Advanced Wireless Settings This tab is used to set up the Router’s advanced wireless functions. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance. Basic Rate. The Basic Rate setting is not actually one rate of transmission but a series of rates, advertising to the other wireless points in your network at what rates the Router can transmit.
Wireless-B Broadband Router RTS Threshold. Should you encounter inconsistent data flow, only minor reduction of the default value, 2346, is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame.
Wireless-B Broadband Router feature make it more difficult for outside users to work their way into your network. This feature is enabled by default. Filter Multicast. This feature allows for multiple transmissions to specific recipients at the same time. Select Enabled to support the feature, or Disabled to keep the Router from multicasting. Change these settings as described here and click the Save Settings button to apply your changes or Cancel Changes to cancel your changes.
Wireless-B Broadband Router The Applications and Gaming Tab - Port Range Forwarding The Applications and Gaming Tab allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.
Wireless-B Broadband Router The Applications and Gaming Tab - Port Triggering Port Triggering Port Triggering is used for special applications that can request a port to be opened on demand. For this feature, the Gateway will watch outgoing data for specific port numbers.
Wireless-B Broadband Router The Applications and Gaming Tab - DMZ The DMZ feature allows one network user to be exposed to the Internet for use of a special-purpose service such as Internet gaming or videoconferencing. DMZ hosting forwards all the ports at the same time to one PC. The Port Range Forward feature is more secure because it only opens the ports you want to have opened, while DMZ hosting opens all the ports of one computer, exposing the computer to the Internet.
Wireless-B Broadband Router To back up or restore a configuration, click the Backup and Restore button and the Backup & Restore Configuration screen will appear. To back up a configuration, click the Backup button. To restore a configuration, click the Browse button to find the file, then click the Restore button. Change these settings as described here and click the Save Settings button to apply your changes or Cancel Changes to cancel your changes.
Wireless-B Broadband Router The Administration Tab - Firmware Upgrade IMPORTANT: Upgrading the firmware could eraseall of your settings (WEP Encryption, Wireless and LAN settings, etc.), and replace them with the factory defaults. Linksys recommends that you back up your configuration settings before you upgrade the firmware. Firmware can be upgraded by following these instructions. Do not upgrade your firmware unless you are experiencing problems with the Router.
Wireless-B Broadband Router The Administration Tab - Factory Defaults Click the Yes button to reset all configuration settings to their default values, and then click the Save Settings button. Any settings you have saved will be lost when the default settings are restored. This feature is disabled by default. Click the Cancel Changes button to cancel your changes. IMPORTANT: Restoring the Router’s factory default settings will erase all of your settings (WEP Encryption, Wireless and LAN settings, etc.
Wireless-B Broadband Router The Status Tab - Router The Router screen on the Status Tab displays the Router’s current status. Firmware Version. This is the Router’s current firmware. MAC Address. This is the Router’s MAC Address, as seen by your ISP. Login Type. The status of the connection is displayed only for PPPoE, RAS, PPTP, or Heart Beat Signal connections.
Wireless-B Broadband Router The Status Tab - Local Network The Local Network screen on the Status Tab displays the status of your network. Local MAC Address. This is the Router’s MAC Address, as seen on your local, Ethernet network. IP Address. This shows the Router’s IP Address, as it appears on your local, Ethernet network. Subnet Mask. When the Router is using a Subnet Mask, it is shown here. DHCP Server. If you are using the Router as a DHCP server, that will be displayed here. DHCP Client Table.
Wireless-B Broadband Router Appendix A: Troubleshooting This appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.” Provided are possible solutions to problems that may occur during the installation and operation of the Router. Read the descriptions below to help you solve your problems. If you can’t find an answer here, check the Linksys website at www.linksys.com. Common Problems and Solutions 1. I need to set a static IP address on a PC.
Wireless-B Broadband Router 7. Toward the bottom of the window, select Use the following DNS server addresses, and enter the Preferred DNS server and Alternative DNS server (provided by your ISP). Contact your ISP or go on its website to find the information. 8. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the Local Area Connection Properties window. 9. Restart the computer if asked.
Wireless-B Broadband Router C. In the command prompt, type ping followed by your Internet or Internet IP address and press the Enter key. The Internet or Internet IP Address can be found on the Status screen of the Router’s web-based utility. For example, if your Internet or Internet IP address is 1.2.3.4, you would enter ping 1.2.3.4 and press the Enter key. • If you get a reply, the computer is connected to the Router.
Wireless-B Broadband Router 7. I need to set up a server behind my Router and make it available to the public. To use a server like a web, ftp, or mail server, you need to know the respective port numbers they are using. For example, port 80 (HTTP) is used for web; port 21 (FTP) is used for FTP, and port 25 (SMTP outgoing) and port 110 (POP3 incoming) are used for the mail server. You can get more information by viewing the documentation provided with the server you installed.
Wireless-B Broadband Router 3. Enter the External Port range of the service you are using. For example, if you want to host Unreal Tournament (UT), you would enter the range 7777 to 27900. 4. Check the protocol you will be using, TCP and/or UDP. 5. Enter the IP address of the PC or network device that you want the port server to go to. For example, if the web server’s Ethernet adapter IP address is 192.168.1.100, you would enter 100 in the field provided.
Wireless-B Broadband Router • Reset the Router to factory default by pressing the Reset button for 10 seconds and then releasing it. If you are still getting prompted for a password when saving settings, then perform the following steps: 1. Access the Router’s web-based utility by going to http://192.168.1.1 or the IP address of the Router. Enter the default password admin, and click the Administrations => Management tab. 2.
Wireless-B Broadband Router • If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s instructions. • Set a static IP address on the PC; refer to “Problem #1, I need to set a static IP address.” Use the following IP address settings for the computer you are using: IP Address: 192.168.1.50 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.
Wireless-B Broadband Router 17. The Power LED keeps flashing. The Power LED flashes when the device is first powered up. Meantime, the system will boot up itself and check for proper operation. After finishing the checking procedure, the LED stays solid to show that the system is working fine. If the LED keeps flashing after this time, the device is not working properly. Try to flash the firmware by assigning a static IP address to the computer, and then upgrade the firmware.
Wireless-B Broadband Router Does the Internet connection of the Router support 100Mbps Ethernet? The Router’s current hardware design supports up to 100Mbps Ethernet on its Internet port; however, the Internet connection speed will vary depending on the speed of your broadband connection. The Router also supports 100Mbps over the auto-sensing Fast Ethernet 10/100 switch on the LAN side of the Router.
Wireless-B Broadband Router the same time, even if on the same LAN (not a problem with 1.0.1.3). As far as hosting games, the HL server does not need to be in the DMZ. Just forward port 27015 to the local IP address of the server computer. How can I block corrupted FTP downloads? If you are experiencing corrupted files when you download a file with your FTP client, try using another FTP program. The web page hangs; downloads are corrupt, or nothing but junk characters are being displayed on the screen.
Wireless-B Broadband Router What is DMZ Hosting? Demilitarized Zone (DMZ) allows one IP address (computer) to be exposed to the Internet. Some applications require multiple TCP/IP ports to be open. It is recommended that you set your computer with a static IP if you want to use DMZ Hosting. To get the LAN IP address, see “Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter.” If DMZ Hosting is used, does the exposed user share the public IP with the Router? No.
Wireless-B Broadband Router • • • • • Multi-Channel Roaming Automatic Rate Selection RTS/CTS feature Fragmentation Power Management What is ad-hoc mode? When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to communicate directly with each other. The ad-hoc wireless network will not communicate with any wired network.
Wireless-B Broadband Router What is Spread Spectrum? Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security.
Wireless-B Broadband Router How do I resolve issues with signal loss? There is no way to know the exact range of your wireless network without testing. Every obstacle placed between the Router and a wireless PC will create signal loss. Lead glass, metal, concrete floors, water and walls will inhibit the signal and reduce range. Start with the Router and your wireless PC in the same room and move it away in small increments to determine the maximum range in your environment.
Wireless-B Broadband Router Appendix B: Wireless Security Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network.
Wireless-B Broadband Router SSID. There are several things to keep in mind about the SSID: 1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast the SSID. Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.
Wireless-B Broadband Router WPA Pre-Shared Key. If you do not have a RADIUS server, select the type of algorithm, enter a password in the Pre-Shared key field of 8-64 characters, and enter a Group Key Renewal period time between 0 and 99,999 seconds, which instructs the Router how often it should change the encryption keys. WPA RADIUS. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) First, select the type of WPA algorithm.
Wireless-B Broadband Router Appendix C: Upgrading Firmware The Access Point's firmware is upgraded through the Web-Utility's Help tab. Follow these instructions: 1. Open Linksys's website at www.linksys.com/international. 2. Select your region, if necessary, and country. 3. Select the Router from the Products tab. 4. Download the firmware from this screen. 5. Go to the Firmware Upgrade screen from the Web-Utility's Administration tab, and the Upgrade Firmware screen will appear. 6.
Wireless-B Broadband Router Appendix D: Windows Help Wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with the Router, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network.
Wireless-B Broadband Router Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC filtering and/or MAC address cloning feature of the Router. You can also find the IP address of your computer’s Ethernet adapter. This IP address is used for the Router’s filtering, forwarding, and/or DMZ features.
Wireless-B Broadband Router 3. Write down the Physical Address as shown on your computer screen; it is the MAC address for your Ethernet adapter. This appears as a series of numbers and letters. The MAC address/Physical Address is what you will use for MAC address cloning or MAC filtering. Note: The MAC address is also called the Physical Address. The example in Figure E-3 shows the Ethernet adapter’s IP address as 192.168.1.100. Your computer may show something different.
Wireless-B Broadband Router Appendix F: Glossary 802.11a - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 5GHz. 802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. 802.11g - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices.
Wireless-B Broadband Router Buffer - A block of memory that temporarily holds data to be worked on later when a device is currently too busy to accept the data. Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the Internet. CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent data loss in a network. CTS (Clear To Send) - A signal sent by a device to indicate that it is ready to receive data.
Wireless-B Broadband Router Dynamic IP Address - A temporary IP address assigned by a DHCP server. Encryption - Encoding data to prevent it from being read by unauthorized people. Ethernet - An IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Finger - A program that tells you the name associated with an e-mail address. Firewall - Security measures that protect the resources of a local network from intruders. Firmware - 1.
Wireless-B Broadband Router IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer. ISM band - Radio band used in wireless networking transmissions. ISP (Internet Service Provider) - A company that provides access to the Internet. LAN (Local Area Network) - The computers and networking products that make up the network in your home or office.
Wireless-B Broadband Router PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication (username and password) in addition to data transport. PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe. Preamble - Part of the wireless signal that synchronizes network traffic.
Wireless-B Broadband Router TCP/IP (Transmission Control Protocol/Internet Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent. Telnet - A user command and TCP/IP protocol used for accessing remote PCs. TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that uses UDP and has no directory or password capability. Throughput - The amount of data moved successfully from one node to another in a given time period.
Wireless-B Broadband Router Appendix G: Specifications Standards IEEE 802.3, IEEE 802.3u, IEEE 802.11b Channels 11 Channels (US, Canada), 13 Channels (most of Europe) 14 Channels (Japan) Ports One 10/100 RJ-45 port for Cable/DSL Modem Connection Four 10/100 RJ-45 Switched ports Speed 10/100Mbps (Half Duplex) 20/200 (Full Duplex) Cabling Type UTP Category 5 or better LEDs Power, Internet, Ethernet, Wireless-B Warranty 1-Year Limited Dimensions 186 mm x 154 mm x 48 mm Unit Weight 0.
Wireless-B Broadband Router Appendix H: Warranty Information Linksys warrants to You that, for a period of one year (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser.
Wireless-B Broadband Router Appendix I: Regulatory Information FCC STATEMENT This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Wireless-B Broadband Router Caution: This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact local Authority for procedure to follow.
Wireless-B Broadband Router Appendix J: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com/international If you experience problems with any Linksys product, you can e-mail us at: In Europe E-mail Address Austria support.at@linksys.com Belgium support.be@linksys.com Denmark support.dk@linksys.com France support.fr@linksys.com Germany support.de@linksys.com Italy support.
