Installation Guide

ManualsBrandsGenStone ManualsBuilding materialsChicago Brick 16.63 in. x 3 in. x 3.75 in. Brick Veneer Siding Outside Corner Ledger

GenStone products are designed to provide a realisc

look of brick. Although installaon of GenStone is

much easier than tradional masonry applicaons,

proper installaon requires good planning and

preparaon. Each applicaon varies, therefore

we recommend you read this enre guide before

beginning your project. When calculang the amount

of GenStone needed for your project, remember that

you will need addional pieces for unique cuts, such

RECOMMENDED TOOLS

OPTIONAL TOOLS

• Hand Saw

• Ulity Knife

• Tape Measure

• Caulking Gun for a 10 oz Tube

• 1.625” Non-Corrosive Deck Screws

• 2.5” Non Corrosive Deck Screw (for Ledger)

• Screw Driver Bits

• Drill

• Framing Square

• Level

• Sandpaper

as gables, end walls, or areas around windows. A

minimum of a 5% addional product is recommended

for mely compleon of your job. Keep in mind,

your le over product can be used in otherareas

of your project to. It is also recommended that

addional panels be purchased and scrap pieces be

kept in case a repair is needed. Observe and Obey

All Safety Rules and Recommendaons set forth by

Tool Manufacturers and Local, State, and Federal

Authories for Any Building Codes Applicable.

BRICK PRODUCT TO WOOD

Exterior Installaons Interior Installaons

• Marker

• Gloves

• Safety Goggles/Glasses

• Table Saw

• Compound Miter Saw

• Jig Saw

• Power Sander

• Rubber Mallet

Summary of content (5 pages)

PAGE 1
BRICK PRODUCT TO WOOD GenStone products are designed to provide a realistic look of brick. Although installation of GenStone is much easier than traditional masonry applications, proper installation requires good planning and preparation. Each application varies, therefore we recommend you read this entire guide before beginning your project.
PAGE 2
IMPORTANT STEPS TO CONSIDER Make sure to use adequate sealants and/ or finishes when joining other products and around penetrations, windows, or doors. GenStone Color Matched Caulking should be used between the shiplap edges to adhere panels together ensuring a good seal. GenStone Color Matched Touch-Up Paint should be used anywhere custom cuts are made. PREPARATION GenStone products are designed to be applied to a variety of substrates.
PAGE 3
MEASURING AND MARKING When using a circular or hand saw, it is best to measure and mark on the flat (back) side of the panel. Use a level or straight edge, pencil or marker, and a tape measure to mark the cut line. If you plan to use a table saw, it would be better to mark a point on the panel surface and use the flat side down on the table. All exposed cut edges should be sealed with GenStone Color Matched Touch-Up Paint. CUTTING AND MEASURING After marking your panels, you are ready to cut.
PAGE 4
NEGATIVE SHIPLAP EDGES Some installations may require a new negative shiplap edge to be cut into a piece. This can be done with a table saw, router or router table, or if neither are available, a circular saw preferably with a guide. Use a panel to determine the height (on the table saw) or depth (with a circular saw) to set the blade. This should be equal to the horizontal cut of the shiplap edge (approximately 1”).
PAGE 5
CAULKING Surfaces must be clean, frost-free, and free of oil, grease, or any other contaminants. Avoid contact with alcohol and solvent cleaners while curing. For the best results, apply a thin bead of caulking, not to exceed 1/2” in thickness, to the positve shiplap edge and behind each of the finger tabs. Fill screw holes with GenStone Color Matched Caulking. Some stones will be a different color than the filler. Use GenStone Color Matched TouchUp Paint to blend the area to the correct color.