User Guide

ManualsBrandsGenteq Motors ManualsEvergreen MotorsEvergreen VS User Interface for Use with Evergreen VS Motors

• Periodic inspections should be performed. Failure to perform

proper maintenance could result in premature product failure, in

addition to minor or moderate injury.

• This Evergreen VS user interface and motor should be

installed in accordance with accepted practices and installation

instructions, and in compliance with all national and local codes.

indicates a hazardous situation that, if not

avoided, could result in minor or moderate injury.

• Read and follow all instructions carefully.

• Disconnect and lock out the main power from the unit being

serviced before installing the Evergreen VS user interface and

motor. It is also a good practice to conﬁrm that the power is

disconnected with a voltmeter.

• Do not operate equipment without guards in place.

• Improper installation, adjustment, alteration, service,

maintenance, or use could cause explosion, ﬁre, electrical shock,

or other conditions. Consult a qualiﬁed installer, service agency,

or your distributor or branch for information or assistance.

The qualiﬁed installer or agency must use the supplied or

recommended parts when installing or servicing this product.

• Installation and service of this Evergreen VS user interface and

motor should be performed only by trained service technicians

familiar with these products.

• After installing the Evergreen VS user interface and motor, it is

the responsibility of the installing technician to verify the HVAC

system matches the manufacturer’s requirements for proper

operation, capacity, efﬁciency and safety. This includes but is not

limited to measuring the airﬂow and adjusting the Evergreen

VS user interface airﬂow and delay setting in each mode of

operation.

indicates a hazardous situation that, if not

avoided, could result in death or serious injury.

F O R M

Evergreen

VS User Interface

Evergreen VS Motor

Installation Guide

G0134E

Revised

December 2021

Regal Beloit America, Inc.

1325 Heil Quaker Blvd.

LaVergne, TN 37086

Customer Service: 800 672 6495

www.thedealertoolbox.com

www.regalrexnord.com

Table of Contents

1. Introduction

2. Evergreen VS Product Line Applications

and How to ID Genteq ECM Motors

3. Applications and Removal and Installation of the Motor

4 - 6. Installation of the Evergreen VS User Interface (UI)

7. User Interface (UI) Overview and Commissioning

8. Sequence of Operation

9. Evergreen VS Optimizer™ Tool

10. Diagnostics and Changing Rotation

11. Speciﬁcations, Technical Support and Warranty

Page

Evergreen

VS Motor

Evergreen

VS User Interface

INTRODUCTION

The Evergreen VS motor is designed to replace Genteq constant airﬂow (variable speed) ECM motors, including ECM indoor blower

motors formerly branded GE

* or GE ECM by Regal Beloit. The Evergreen VS motor is a constant airﬂow (variable speed) motor. It will

operate in constant airﬂow mode when it is receiving digital serial interface (DSI) and constant torque mode when it is receiving pulse

width modulation (PWM) communication.

NOTE: The Genteq Evergreen VS user interface # 5K010V is the second generation of this product. The thermostat and motor

connections are the same as the ﬁrst generation (# 5K010), see pages 3-6 of this manual. See pages 7-8 for the simpliﬁed operation

information and the newly added OPTIONAL features available in the app using the built in WIFI.

*GE is believed to be the trademark and/or trade name of General Electric Company and is not owned or controlled by Regal Rexnord Corporation.

Summary of content (11 pages)

PAGE 1
FORM Regal Beloit America, Inc. Evergreen® VS User Interface Evergreen VS Motor Installation Guide 1325 Heil Quaker Blvd. LaVergne, TN 37086 Customer Service: 800 672 6495 www.thedealertoolbox.com www.regalrexnord.com G0134E Revised December 2021 indicates a hazardous situation that, if not avoided, could result in death or serious injury. indicates a hazardous situation that, if not avoided, could result in minor or moderate injury. • Read and follow all instructions carefully.
PAGE 2
APPLICATIONS - EVERGREEN® VS PRODUCT LINE The Evergreen VS motor can be used to replace multiple Genteq® constant airflow motors either by itself or in conjunction with the correct accessory. Use the chart below to select the correct components for your application. NOTE: Use this manual to replace model 2.0, Genteq models 2.3 and Eon® motors with Evergreen VS motor and User Interface. NOTE: When replacing model 2.5 and Genteq model 3.0, use the installation manual supplied with the motor.
PAGE 3
APPLICATIONS Replacing GE®* model 2.0, Genteq® models 2.3 and Eon® motors – Applications o Furnace, air handler and package units o Fossil fuel, electric strip heat, A/C, heat pump and geothermal units – Install (1) Evergreen® VS user interface (Stock # 5K010V) – Install (1) Evergreen VS motor o – GE Model 2.0 Genteq ECM model 2.3 motor Genteq ECM Eon motor For proper replacement of model 2.0, Genteq ECM models 2.
PAGE 4
INSTALLING THE EVERGREEN® VS USER INTERFACE (UI) Install the UI so that the buttons are accessible and visible. Orient the UI so that the thermostat wires face down in the HVAC system. There are three holes in each side wing for mounting, and there is two-sided tape on the back.
PAGE 5
Thermostat wiring diagrams for connecting the Evergreen® VS user interface to: – All electric air handlers and package units o With or without electric strip heat o With or without A/C or heat pump systems o A/C systems DO NOT use the orange wire The thermostat wire designations and connections legend are provided on either side of the thermostat wire harness decal. 5 ©2019, 2020, 2021 Regal Rexnord Corporation, All Rights Reserved.
PAGE 6
Thermostat wiring diagrams for connecting the Evergreen® VS user interface to: – Fossil fuel furnaces and package units o Including gas, propane or oil o With or without A/C or heat pump systems o A/C systems DO NOT use the orange wire Single Stage Thermostat Systems Two Stage Thermostat Systems 6 ©2019, 2020, 2021 Regal Rexnord Corporation, All Rights Reserved.
PAGE 7
EVERGREEN® VS USER INTERFACE (UI) OVERVIEW The user interface is pre-programmed with the following default airflow and delays for each mode of operation: Defaults W1 W2 Y1 Y2 G W1-W2 Y1-Y2 %A/F = 60 - On Delay = 0 seconds %A/F = 85 - On Delay = 0 seconds %A/F = 60 - On Delay = 0 seconds %A/F = 85 - On Delay = 0 seconds %A/F = 40 - On Delay = 0 seconds Time Delay 10 minutes Time Delay 10 minutes - Off Delay = 90 seconds Off Delay = 90 seconds Off Delay = 0 seconds Off Delay = 0 seconds Off Delay = 0 se
PAGE 8
SEQUENCE OF OPERATION Assuming the default ON/OFF delays have not been changed and the user interface (UI) is receiving 24 VAC on the RED and BLUE thermostat wires, the following will occur: 1. When the UI receives a thermostat input, the (UI Input Indicator) will change from ON to CONTINUOUS BLINKING. 2. The (Motor Indicator) will change from OFF to SOLID ON, and the motor will turn on. The motor will operate at the default airflow setting or the last value selected in this demand. 3.
PAGE 9
EVERGREEN® VS OPTIMIZER™ TOOL The Evergreen VS user interface (UI) is built with WIFI so that it can connect wirelessly to the Evergreen VS Optimizer tool on a smart phone. The Evergreen VS Optimizer tool is one of the tools available in the Dealer Toolbelt app. The Dealer Toolbelt app is available on both Apple Store®* and Google Play™*. Search the app store for key word "DEALER TOOLBELT".
PAGE 10
DIAGNOSTICS If the motor does not operate: The Evergreen® VS motor will only operate if it is receiving line voltage AND communication input from the user interface (UI). 1. Measure the line voltage at the 5-pin plug connected to the motor. Use the HVAC system schematic if needed. If proper voltage is not present, solve the issue with the HVAC system controls or wiring. If/when proper voltage is present (voltage matching the rating on the motor), go to the next step. 2.
PAGE 11
EVERGREEN® VS USER INTERFACE (UI) SPECIFICATIONS Approximate Dimensions: 5.25" x 3.1" x 1.