Gentex by VOXX Corporation Installation Instructions Bezelled ADVGEN45A4 Bezelled w/ Homelink ADVGEN45A4PW4 ADVGEN80EXP ADVGEN40A4 ADVGEN45A4PW4 ADVGEN45AB5 ADVGEN40A4 ADVGEN45A4 Frameless ADVGEN8EXP Frameless w/ Homelink ADVGEN85EXP ADVGENFL85EXP ADVGEN45AB5 ADVGENFL80EXP TOOLS REQUIRED: Safety Glasses Clean Rag DC Voltmeter Page 1 of 10 Utility Knife Electrical Tape Fish-Wire (Coat Hanger) Pliers 4mm Flat Screwdriver #T20 Torx Driver Revision A #2 Phillip's Screwdriver Flashlight Panel Removal T
INSTALLATION PRECAUTIONS / NOTES: Do not use excessive force when removing OEM mirror from windshield. Do not push fish-wire too far into dash to avoid damage to existing components. Do not place wire harness against objects with sharp edges that may cause electrical shorting. On vehicles equipped with A-pillar (side impact or SRS) airbags, verify mirror harness path remains clear of airbag. Harness should follow and be secured to, existing OEM wiring with tie wraps.
CAUTION ! 8. Remove OEM mirror. (Fig. 6,7 or 8) CAUTION Do not use excessive force. Damage to windshield could occur. ! 6 a) Loosen #T20 torx screw on mirror mount and slide mirror upwards off from windshield button. (Fig. 6) - - OR - b) Insert 4mm into opening at bottom of mirror mount to disengage locking tab and slide mirror upwards off from windshield button. (Fig. 7) NOTE: Gently wiggling mirror while sliding upwards will assist removal.
2. Locate constant power (+12V constant) wire. a) Using a multi-meter, find a wire exiting the fuse block that tests +12V with vehicle ignition in the ACC, ON and OFF positions. (Fig. 11) 11 b) Ensure power in this wire is still present when vehicle key is OFF and label wire "CONSTANT." 3. Disconnect vehicle's negative battery terminal. (Fig. 12) 12 4. Plug auto-dimming mirror harness into back of mirror. (Fig. 13) 13 5. Route harness up to vehicle headliner. (Fig.
7. Route harness down A-pillar. (Fig. 17) NOTE: Harness will be secured later in installation procedure. 17 8. Route harness to vehicle connection wires. a) Using fish-wire, route harness from base of A-pillar through dash and into connection wire / fuse block area. (Fig. 18) 18 9. Attach wire tap to vehicle wire marked IGNITION. a) Center blade of wire tap on IGNITION wire and close wire tap with pliers. (Fig. 19) 19 b) Ensure both halves of wire tap are closed completely and locking tab is engaged.
13. Connect auto-dimming mirror harness ground wire. a) Locate a ground bolt near connection / fuse block area and remove. NOTE: Bolt locations may vary but common locations are in the kick plate / cowl cover area or parking brake release handle. 23 b) Install ring terminal of harness over bolt and reinstall. (Fig. 23) 5 Testing. 1. Reconnect negative battery cable. 2. Turn the ignition switch ON/ACC position. 3.
6 Compass Zone Adjustment 1. Adjust compass zone after EC mirror installation. a) The zone setting is factory preset to Zone 8. Refer to Compass Calibration Zone Map to find correct compass zone setting for your geographical location. (Fig. 27) 1 2 1 5 2 3 4 5 3 1 4 1 3 67 1 2 89 1 1 01 1 4 1 3 27 4 1 2 1 1 5 1 0 6 7 8 9 b) To change the zone setting, push and hold the button until a number appears in the display. Press button repeatedly until desired compass zone number is reached.
HomeLink® Feature and Programming Instructions ® To Operate the HomeLink Feature: Please refer to the programming instructions outlined in this manual or: ® a) Visit the HomeLink website at www.homelink.com ® b) Call the HomeLink customer support line at 1-800-355-3515 WARNING! Before programming HomeLink® to a garage door opener or gate operator, make sure that people and objects are out of the way of the device to prevent potential harm or damage.
NOTE: Some gate operator and garage door openers may require you to replace this Programming step 4 with procedures noted in the “Gate Operator / Canadian Programming” section. ® 5. After the HomeLink indicator light changes from a slow to a rapidly ® blinking light, release both the HomeLink and hand-held transmitter buttons. ® 6. Press and hold the just-trained HomeLink button and observe the indicator light.
TROUBLESHOOTING PROBLEM 1 "C" or "CAL" is displayed in display window 2 Inaccurate compass direction 3 Mirror does not dim 4 Mirror dims constantly 5 Cannot program garage door opener or other remote control device 6 Display window shows "SC" (short circuit) SOLUTION Perform calibration sequence (ref. Sec. 8) Perform compass zone setting procedure (ref. Sec. 7) Vehicle magnetics may have changed. Perform calibration sequence (ref. Sec.
