Product Info

ManualsBrandsGentex ManualsElectronicsWireless Garage Door Opener



Garage door opener

RADIO FREQUENCY (RF) TRANSCEIVER

[G2001751]

WARNINGS:

Do not use the Radio Frequency (RF) transceiver with any garage door opener that lacks the safety stop and

reverse feature, as required by safety standards. A closing garage door may cause serious injuries or death.

Do not use the RF transceiver with any garage door opener that was manufactured before April 1982. An

outdated garage door opener can lead to malfunction of the garage door, potentially causing serious injury or

death.

When programming the RF transceiver to a garage door opener or entry gate, make sure that the area is

clear of people and objects. Potential harm or damage may occur, as the gate or garage door activates during

programming.

CAUTION: The system may suffer from interference if operated in the vicinity of a mobile or fixed station

transmitter. Interference is likely to affect the hand-held transmitter, as well as the RF transceiver. See

See INFORMATION AND ASSISTANCE.

The RF transceiver is also known as HomeLink

The HomeLink device is located in the rear-view mirror.

The hand-held transmitter is also known as a garage door remote.

The HomeLink wireless control system provides a convenient way to replace up to three remote controls. HomeLink

can be used to activate devices such as gate operators, garage door openers, entry door locks, security systems,

and home lighting.

HomeLink

is a registered trademark of Gentex Corporation.

BEFORE PROGRAMMING

[G2001753]

CAUTION: Unplug the remote device during programming if repeated operation of the remote control is

required. Repeated operation of the remote control during programming may result in damage to the remote

device.

NOTE: HomeLink

is compatible with a wide range of remote devices. For information on compatible devices

and instructional videos, visit: www.HomeLink.com.

For the best results, fit a new battery to the remote control before programming. If the remote device’s receiver is

equipped with an antenna, make sure the antenna is extended.

HomeLink

is a registered trademark of Gentex Corporation.

PROGRAMMING

[G2200557]

Summary of content (5 pages)

PAGE 1
Garage door opener RADIO FREQUENCY (RF) TRANSCEIVER [G2001751] WARNINGS: Do not use the Radio Frequency (RF) transceiver with any garage door opener that lacks the safety stop and reverse feature, as required by safety standards. A closing garage door may cause serious injuries or death. Do not use the RF transceiver with any garage door opener that was manufactured before April 1982. An outdated garage door opener can lead to malfunction of the garage door, potentially causing serious injury or death.
PAGE 2
NOTES: The instructions below apply to the majority of HomeLink compatible systems. However, there are some HomeLink applications, or HomeLink compatible systems, that require slightly different instructions. For more information and instructional videos, visit: www.HomeLink.com. Garage door openers manufactured after 1995 may be equipped with rolling code protection. In this case, a stepladder, or other sturdy, safe device, may be required to reach the learn or smart button on the garage door opener. 1.
PAGE 3
1. Locate the learn or smart button on the garage door opener motor-head unit. NOTE: The learn or smart button can usually be found directly on the motor-head unit. If in doubt, refer to the garage door opener manual to identify the button. 2. Firmly press and release the learn or smart button. There are typically 30 seconds to initiate Step 7. 3. Return to the vehicle. Firmly press and release the programmed HomeLink button up to three separate times to activate the device.
PAGE 4
1. Switch the vehicle’s ignition on. 2. Press and hold the outer two HomeLink buttons until the LED on the rear-view mirror changes from continuously illuminated orange to flashing green. NOTE: Do not press and hold the buttons for longer than 20 seconds. 3. Release the buttons. HomeLink is initialised and the previous settings of all three buttons are erased. HomeLink® is a registered trademark of Gentex Corporation.
PAGE 5
FCC (États-Unis) et ISED (Canada) Cet appareil est conforme aux règlements de la FCC, section 15, et au CNR-210 d’Innovation, Sciences et Développement économique Canada. Le fonctionnement est assujetti aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférences nuisibles et (2) cet appareil doit accepter toute interférence reçue, y compris celle qui pourrait entraîner un dysfonctionnement.