For your information Main Owner’s Manual Please note that this manual applies to all models and all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle. All specifications provided in this manual are current at the time of printing. However, because of the Toyota policy of continual product improvement, we reserve the right to make changes at any time without notice.
Installation of a mobile two-way radio system The installation of a mobile two-way radio system in your vehicle could affect electronic systems such as: ● Multiport fuel injection system/sequential multiport fuel injection system ● Cruise control system ● Anti-lock brake system ● SRS airbag system ● Seat belt pretensioner system Be sure to check with your Toyota dealer for precautionary measures or special instructions regarding installation of a mobile two-way radio system.
Vehicle control and operation data recording Your Toyota is equipped with sophisticated computers that record certain information about your vehicle’s operation, such as: • Engine speed • Accelerator status • Brake status • Vehicle speed • Shift position The data recorded varies according to the grade level and options the vehicle is equipped with. The computers do not record conversations, sound or pictures.
● Event data recorder Your vehicle has computers that monitor and control certain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Besides storing data useful for troubleshooting, there is an event data recorder (EDR) that records data in a crash or near crash event. The SRS airbag sensor assembly contains the EDR.
● Safety Connect If your Toyota has Safety Connect and if you have subscribed to those services, please refer to the Safety Connect Telematics Subscription Service Agreement for information on data collected and its usage. CAUTION ■ General precautions while driving Driving under the influence: Never drive your vehicle when under the influence of alcohol or drugs that have impaired your ability to operate your vehicle.
Symbols used throughout this manual Cautions & Notices CAUTION This is a warning against something which, if ignored, may cause death or serious injury to people. You are informed about what you must or must not do in order to reduce the risk of death or serious injury to yourself and others. NOTICE This is a warning against something which, if ignored, may cause damage to the vehicle or its equipment.
30 4RUNNER_U I nf or mat i onPr ovi dedby:
TABLE OF CONTENTS 1 Before driving Adjusting and operating features such as door locks, mirrors, and steering column. 2 When driving Driving, stopping and safe-driving information. 3 Interior features Air conditioning and audio systems, as well as other interior features for a comfortable driving experience. 4 Maintenance and care Cleaning and protecting your vehicle, performing do-ityourself maintenance, and maintenance information.
1-1. Key information Keys The following keys are provided with the vehicle. Vehicles without a smart key system Master keys Operating the wireless remote control function (→P. 49) Valet key Key number plate Vehicles with a smart key system Electronic keys • Operating the smart key system (→P. 35) • Operating the wireless remote control function (→P.
1-1. Key information Using the mechanical key (vehicles with a smart key system) To take out the mechanical key, push the release button and take the key out. ■ When required to leave the vehicle’s key with a parking attendant Lock the glove box as circumstances demand. (→P. 442) Vehicles without a smart key system: Carry the master key for your own use and provide the attendant with the valet key.
1-1. Key information NOTICE ■ To prevent key damage Observe the following: ● Do not drop the keys, subject them to strong shocks or bend them. ● Do not expose the keys to high temperatures for a long period of time. ● Do not get the keys wet or wash them in an ultrasonic washer etc. ● Do not attach metallic or magnetic materials to the keys or place the keys close to such materials. ● Do not disassemble the keys. ● Do not attach a sticker or anything else to the surface of the electronic key.
1-2. Opening, closing and locking the doors Smart key system∗ The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.) 1 Before driving Electronic key Electronic key Electronic key Electronic key CTH12AS053 Locks and unlocks the side doors (→P. 36) Locks, unlocks and opens the back door (→P. 37) Opens the back door (→P. 36) Starts the engine (→P.
1-2. Opening, closing and locking the doors Unlocking and locking the side doors (front door handles only) Grip the handle to unlock the door. Make sure to touch the sensor on the back of the handle. The doors cannot be unlocked for 3 seconds after the doors are locked. Touch the lock sensor (the indentation on the upper part of the door handle) to lock the doors. Opening the back door Press the back door opener. The back door can be opened even if it is locked.
1-2. Opening, closing and locking the doors Unlocking and locking the back door Press the button to unlock the door. Press the button to lock the door. The back window can be closed by pressing and holding this button. (→P. 101) 37 4RUNNER_U I nf or mat i onPr ovi dedby: 1 Before driving The back window can be opened by pressing and holding this button. (→P.
1-2.
1-2. Opening, closing and locking the doors ■ Effective range (areas within which the electronic key is detected) When locking or unlocking the doors When starting the engine or changing “ENGINE START STOP” switch modes The system can be operated when the electronic key is inside the vehicle. 39 4RUNNER_U I nf or mat i onPr ovi dedby: 1 Before driving CTH12AS051 The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) either of the outside front door handles and back door.
1-2. Opening, closing and locking the doors ■ Operation signals A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: once; Unlocked: twice) ■ When the door cannot be locked by the lock sensor on the upper part of the door handle Touch both lock sensors on the upper and lower part of the door handle simultaneously.
1-2. Opening, closing and locking the doors The following table describes circumstances and correction procedures when only alarms are sounded. Alarm Situation Correction procedure An attempt was made to lock the doors using the entry function while the electronic key was still inside the vehicle.
1-2. Opening, closing and locking the doors Alarm Interior alarm sounds once. Situation The “ENGINE START STOP” switch was pressed after the doors were unlocked with the mechanical key. The “ENGINE START STOP” switch was pressed two consecutive times without the electronic key being present. Correction procedure Touch the electronic key to the “ENGINE START STOP” switch while depressing the brake pedal.
1-2. Opening, closing and locking the doors ■ Conditions affecting operation The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system, wireless remote control and immobilizer system from operating properly. (Way of coping →P.
1-2. Opening, closing and locking the doors ■ Note for the entry function ● Even when the electronic key is within the effective range (detection areas), the system may not operate properly in the following cases: • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked. • The electronic key is on the instrument panel or floor, in the glove box, or in the auxiliary box of the instrument panel.
1-2. Opening, closing and locking the doors ● If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a buzzer will sound outside the vehicle. To turn off the alarm, lock all the doors. ● The lock sensor may not work properly if it comes into contact with ice, snow, mud, etc. Clean the lock sensor and attempt to operate it again, or use the lock sensor on the lower part of the door handle.
1-2. Opening, closing and locking the doors ■ Electronic key battery depletion ● The standard battery life is 1 to 2 years. ● As the electronic key always receives radio waves, the battery will become depleted even if the electronic key is not used. The following symptoms indicate that the electronic key battery may be depleted. Replace the battery when necessary. (→P. 552) • The smart key system or the wireless remote control does not operate. • The detection area becomes smaller.
1-2. Opening, closing and locking the doors ■ When the electronic key battery is fully depleted →P. 552 ■ Customization that can be configured at Toyota dealer Settings (e.g. smart key system) can be changed. (Customizable features →P. 660) 1 Before driving ■ Certification for the smart key system For vehicles sold in the U.S.A. FCC ID: NI4TMIMB-2 FCC ID: NI4TMLF8-14 FCC ID: HYQ14ACX FCC ID: HYQ13CZD FCC ID: HYQ14ADF FCC ID: HYQ13CZE NOTE: This device complies with part 15 of the FCC Rules.
1-2. Opening, closing and locking the doors CAUTION ■ Caution regarding interference with electronic devices ● People with implanted pacemakers or cardiac defibrillators should keep away from the smart key system antennas. (→P. 38) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves.
1-2. Opening, closing and locking the doors Wireless remote control The wireless remote control can be used to lock and unlock the vehicle. Vehicles without a smart key system 1 Locks all the doors Before driving Sounds the alarm (press and hold) (→P. 50) Unlocks all the doors CTH12AS045 Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors.
1-2. Opening, closing and locking the doors ■ Operation signals A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: once; Unlocked: twice) ■ Door lock buzzer If an attempt to lock the doors is made when a door is not fully closed, a buzzer sounds continuously. Fully close the door to stop the buzzer, and lock the vehicle once more.
1-2.
1-2. Opening, closing and locking the doors ■ Customization that can be configured at Toyota dealer Settings (e.g. wireless remote control system) can be changed. (Customizable features →P. 660) ■ Certification for wireless remote control For vehicles sold in the U.S.A. FCC ID: HYQ14ACX FCC ID: HYQ13CZD FCC ID: HYQ14ADF FCC ID: HYQ13CZE FCC ID: HYQ12BBY FCC ID: HYQ13BDC NOTE: This device complies with part 15 of the FCC Rules.
1-2. Opening, closing and locking the doors Side doors The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch. ■ Entry function (vehicles with a smart key system) 1 →P. 35 Before driving ■ Wireless remote control →P. 49 ■ Key Turning the key operates the doors as follows: Vehicles without a smart key system Locks all the doors Unlocks all the doors Turning the key unlocks the driver's door. Turning the key again unlocks the other doors.
1-2. Opening, closing and locking the doors ■ Door lock switch Locks all the doors Unlocks all the doors CTH12AS013 ■ Inside lock buttons Locks the door Unlocks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.
1-2. Opening, closing and locking the doors Locking the doors from the outside without a key STEP 1 Move the inside lock button to the lock position. STEP 2 Close the door. 1 Vehicles without a smart key system Vehicles with a smart key system The door cannot be locked if the “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode, or the electronic key is left inside the vehicle. The key may not be detected correctly and the door may be locked.
1-2. Opening, closing and locking the doors Automatic door locking and unlocking systems The following functions can be set or canceled: Function Operation Shift position linked door locking function Shifting the shift lever out of P locks all the doors. Shift position linked door unlocking function Shifting the shift lever to P unlocks all the doors. Speed linked door locking function All the doors are locked when the vehicle speed is approximately 12 mph (20 km/h) or higher.
1-2. Opening, closing and locking the doors Shift the shift lever to P or N, and press and hold the driver's door lock switch ( or ) for approximately 5 seconds and then release. STEP 2 Use the same procedure to cancel the function.
1-2. Opening, closing and locking the doors CAUTION ■ To prevent an accident Observe the following precautions while driving the vehicle. Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ● Always use a seat belt. ● Always lock all the doors. ● Ensure that all doors are properly closed. ● Do not pull the inside handle of the doors while driving.
1-2. Opening, closing and locking the doors Automatic running boards∗ The Automatic running boards are linked to the side door operations, extending and retracting when a side door is opened and closed. When a door is opened or closed, the board on the same side extends or retracts.
1-2. Opening, closing and locking the doors Turning off the Automatic running boards system Press “OFF” on the Automatic running boards switch to turn off the Automatic running boards system. On (Automatic mode) Off The orange line at the top of the switch illuminates to indicate that the Automatic running boards system is on.
1-2. Opening, closing and locking the doors ■ Automatic retraction function The boards will be automatically retracted, for safety, under the following conditions: ● A board is not completely retracted 1 ● Vehicle speed is approximately 5 mph (8 km/h) or higher ■ If the Automatic running boards indicator comes on when driving first commences A board has not completely retracted. Check that no obstacles are caught between a board and the vehicle.
1-2. Opening, closing and locking the doors CAUTION ■ Jam protection function Observe the following precautions. Failure to do so may cause serious injury. Never use any part of your body to intentionally activate the jam protection function. The jam protection function may not work depending on the shape of the object that is caught. Be careful not to get fingers or other body parts caught. ■ Cautions regarding the Automatic running boards Observe the following precautions.
1-2. Opening, closing and locking the doors Back door The back door can be locked/unlocked and opened by the following procedures: ■ Locking and unlocking the back door 1 Entry function (vehicles with a smart key system) →P. 36 Before driving Wireless remote control →P. 49 Door lock switch →P. 54 Keys (vehicles without a smart key system) Unlocks all the doors Opens the back window (turn and hold) (→P. 101) Locks all the doors Closes the back window (turn and hold) (→P.
1-2. Opening, closing and locking the doors Rear step bumper The rear step bumper is intended for rear end protection and easier step-up loading. CTH12AS019 ■ When closing the back door Lower the back door using the back door handle, and make sure to push the back door down from the outside to close it.
1-2. Opening, closing and locking the doors CAUTION ■ Caution while driving ● Before driving the vehicle, make sure that the back door is fully closed. If the back door is not fully closed, it may open unexpectedly while driving, causing an accident. ● Never let anyone sit in the luggage compartment. In the event of sudden braking or a collision, they are susceptible to death or serious injury. ● Do not get on the rear step bumper. ■ When children are in the vehicle Observe the following precautions.
1-2. Opening, closing and locking the doors CAUTION ● When opening or closing the back door, thoroughly check to make sure the surrounding area is safe. ● If anyone is in the vicinity, make sure they are safe and let them know that the back door is about to open or close. ● Use caution when opening or closing the back door in windy weather as it may move abruptly in strong wind. CTH12AS035 ● The back door may fall if it is not opened fully.
1-2. Opening, closing and locking the doors NOTICE ■ To prevent damage to the back door components Do not allow more than one person to get on the rear step bumper at a time. 1 ■ Back door damper stays Observe the following precautions. Failure to do so may cause damage to the back door damper stay, resulting in malfunction. ● Do not attach any foreign objects, such as stickers, plastic sheets, or adhesives to the damper stay rod. ● Do not touch the damper stay rod with gloves or other fabric items.
1-3.
1-3.
1-3. Adjustable components (seats, mirrors, steering wheel) ■ The auto away function for exiting the driver seat If the seat is already close to the rearmost position, the auto away function may not operate when the driver exits the vehicle. ■ Active head restraints Even small forces applied to the seatback may cause the head restraint to move. Pushing up a locked head restraint forcibly may appear the head restraint inner structure. These do not indicate problems.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Seat adjustment ● After adjusting the seat, make sure that the seat is locked in position. 71 4RUNNER_U I nf or mat i onPr ovi dedby: 1 Before driving ● To reduce the risk of sliding under the lap belt during a collision, do not recline the seat more than necessary.
1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats Vehicles without third row seats ■ Rear seat Pull up the seatback angle adjustment lever until the lock is released.
1-3. Adjustable components (seats, mirrors, steering wheel) Vehicles with third row seats ■ Second row seats Seat position lever adjustment 1 Before driving Seatback angle adjustment lever CTH13AS053 ■ Third row seats The third row seats do not have a seat adjustment function.
1-3. Adjustable components (seats, mirrors, steering wheel) Folding down the rear seats (vehicles without third row seats) ■ Before folding down the rear seats STEP 1 Adjust the head restraints to the downmost position. STEP 2 Fold down the head restraints. When returning the head restraints to their original positions, make sure they are locked securely. Stow the rear seat belt buckles.
1-3. Adjustable components (seats, mirrors, steering wheel) ■ Folding down the rear seats Swing the bottom cushions up by pulling the lock release strap. STEP 1 Push the lock release button and fold down the seatbacks. STEP 2 To return the rear seatbacks to their original positions, lift them up until they lock. ■ Folding down rear center seatback only Pull the center seatback angle lever behind the seatback and fold the seatback down.
1-3. Adjustable components (seats, mirrors, steering wheel) Folding down the second row seats (vehicles with third row seats) ■ Before folding down the second row seats Adjust the head restraints to the downmost position. STEP 1 CTH13AS045 Stow the second row seat belt buckles.
1-3. Adjustable components (seats, mirrors, steering wheel) ■ Folding down the second row seats Pull the seatback lock release lever and fold the seatback down. CTH13AS051 ■ Folding down the second row center seatback only Pull the center seatback angle lever behind the seatback and fold the seatback down. To return the second row center seatback to its original position, lift it up until it locks.
1-3. Adjustable components (seats, mirrors, steering wheel) Moving a second row seat for access to the third row seats (vehicles with third row seats) ■ Getting in the vehicle (right side only) Pull up the lever and fold down the seatback. The seat will slide forward. Move the seat to the front-most position. CTH13AS057 ■ Getting out of the vehicle (right side only) Lift the lever on the back of the seatback and fold down the seatback. The seat will slide forward.
1-3. Adjustable components (seats, mirrors, steering wheel) Folding down the third row seats (vehicles with third row seats) ■ Before folding down the third row seats Pass the seat belts through the seat belt hangers and secure the seat belt plates. Make sure that the seat belts are removed from the hangers before using them. CTH13AS072 ■ Folding down the third row seats From inside Pull the strap to fold down the head restraint. STEP 1 CTH13AS025 Pull the lever up.
1-3. Adjustable components (seats, mirrors, steering wheel) Pull the lever to unlock the seatback and then fold the seatback down. STEP 3 CTH13AS027 From outside Pull the strap to fold down the head restraint. STEP 1 CTH13AS028 Pull the lever up. STEP 2 The seat cushion will slide backward and the seatback will be unlocked. CTH13AS029 Fold the seatback down.
1-3. Adjustable components (seats, mirrors, steering wheel) ■ Returning the third row seats As the seat cushions cannot be pulled forward from outside, this operation can only be performed from inside. Raise the seatbacks to their original positions. STEP 1 they are locked CTH13AS061 Pull the seat cushions forward. STEP 2 CTH13AS062 Raise the head restraints. STEP 3 CTH13AS063 81 4RUNNER_U I nf or mat i onPr ovi dedby: Before driving Make sure securely.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When folding the rear seatbacks down Observe the following precautions. Failure to do so may result in death or serious injury. ● Do not fold the seatbacks down while driving. ● Stop the vehicle on level ground, set the parking brake and shift the shift lever to P. ● Do not allow anyone to sit on a folded seatback or in the luggage compartment while driving. ● Do not allow children to enter the luggage compartment.
1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. ■ Adjusting the head restraints Front and second seats 1 Up Before driving Pull the head restraints up. Down Lock release button Push the head restraint down while pushing the lock release button.
1-3. Adjustable components (seats, mirrors, steering wheel) ■ Removing the head restraints (except third row seats) Pull the head restraint up while pressing the lock release button. CTH13AS036 ■ Installing the head restraints (except third row seats) Align the head restraint with the installation holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Head restraint precautions Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. 1 ● Use the head restraints designed for each respective seat. ● After adjusting the head restraints, push down on them and make sure they are locked in position. ● Do not drive with the head restraints removed.
1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driving the vehicle. ■ Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoulder. CTH13AS038 ● Position the lap belt as low as possible over the hips. ● Adjust the position of the seatback. Sit up straight and well back in the seat.
1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the seat belt shoulder anchor height (front seats) Push the seat belt shoulder anchor down while pressing the release button. 1 Before driving Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed until you hear a click.
1-3. Adjustable components (seats, mirrors, steering wheel) ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully. ■ Automatic locking retractor (ALR) When a passenger's shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended.
1-3. Adjustable components (seats, mirrors, steering wheel) ■ Child seat belt usage The seat belts of your vehicle were principally designed for persons of adult size. ● Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle’s seat belt. (→P.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failure to do so may cause death or serious injury. ■ Wearing a seat belt ● Ensure that all passengers wear a seat belt. ● Always wear a seat belt properly. ● Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Adjustable shoulder anchor ■ Seat belt damage and wear ● Do not damage the seat belts by allowing the belt, plate, or buckle to be jammed in the door. ● Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belts cannot protect an occupant from death or serious injury. ● Ensure that the belt and plate are locked and the belt is not twisted.
1-3. Adjustable components (seats, mirrors, steering wheel) NOTICE ■ When using a seat belt extender When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and push the lever down. STEP 1 1 Before driving CTH13AS007 Adjust to the ideal position by moving the steering wheel horizontally and vertically. STEP 2 After adjustment, pull the lever up to secure the steering wheel. CTH13AS008 CAUTION ■ Caution while driving Do not adjust the steering wheel while driving.
1-3. Adjustable components (seats, mirrors, steering wheel) Inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions: Manual anti-glare inside rear view mirror (if equipped) Normal position Anti-glare position CTH13AS001 Auto anti-glare inside rear view mirror (if equipped) In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.
1-3. Adjustable components (seats, mirrors, steering wheel) Adjusting the height of rear view mirror Adjust the height of the rear view mirror by moving it up and down. Before driving CTH13AS074 ■ To prevent sensor error (vehicles with auto anti-glare inside rear view mirror) To ensure that the sensors operate properly, do not touch or cover them. CTH13AS088 CAUTION ■ Caution while driving Do not adjust the position of the mirror while driving.
1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted using the switch. To select a mirror to adjust, press the switch. STEP 1 Left Right CTH13AS004 To adjust the mirror, press the switch. STEP 2 Up Right Down Left CTH13AS005 Folding the mirrors Push the mirror back in the direction of the vehicle's rear.
1-3. Adjustable components (seats, mirrors, steering wheel) ■ Mirror angle can be adjusted when Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. ■ When the mirrors are fogged up Turn on the mirror defoggers to defog the mirrors. (→P. 328) CAUTION ■ When driving the vehicle Observe the following precautions while driving. Failure to do so may result in loss of control of the vehicle and cause an accident, resulting in death or serious injury.
1-4. Opening and closing the windows and moon roof Power windows The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows: Closing One-touch closing* Opening One-touch opening* *: Pushing the switch in the opposite direction will stop window travel partway. CTH14AS010 Window lock switch Press the switch down to lock the passenger window switches and back window switch.
1-4. Opening and closing the windows and moon roof ■ Operating the power windows after turning the engine off Vehicles without a smart key system The power windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They cannot, however, be operated once either front door is opened. ■ Jam protection function If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.
1-4. Opening and closing the windows and moon roof STEP 3 Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed. If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
1-4. Opening and closing the windows and moon roof Power back window The power back window can be opened and closed using the switch or key. From inside the vehicle 1 Closing Opening One-touch opening* *: Pressing the switch in the opposite direction will stop window travel partway. CTH14AS019 From outside the vehicle (vehicles without a smart key system) Opening Closing Turn the key fully and hold it.
1-4. Opening and closing the windows and moon roof From outside the vehicle (vehicles with a smart key system) Opening (push and hold) Closing (push and hold) This operation can only be performed when the electronic key is within the detection range. CTH14AS018 ■ The power back window can be operated from inside the vehicle when Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.
1-4. Opening and closing the windows and moon roof ■ Operating the power back window from inside the vehicle after turning the engine off Vehicles without a smart key system The power back window can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. It cannot, however, be operated once either front door is opened.
1-4. Opening and closing the windows and moon roof If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer. ■ Customization that can be configured at Toyota dealer Settings (e.g. linked operation) can be changed. (Customizable features →P.
1-4. Opening and closing the windows and moon roof Moon roof∗ Use the overhead switches to open and close the moon roof and tilt it up and down. ■ Opening and closing 1 Opens the moon roof* Press the switch again to fully open the moon roof. Closes the moon roof* CTH14AS020 *: Lightly press the switch in either direction to stop the moon roof partway.
1-4. Opening and closing the windows and moon roof ■ The moon roof can be operated when Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. ■ Operating the moon roof after turning the engine off Vehicles without a smart key system The moon roof can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position.
1-4. Opening and closing the windows and moon roof ■ When the moon roof does not close normally Perform the following procedure: ● If the moon roof closes but then re-opens slightly STEP 1 Stop the vehicle. 1 STEP 2 Press and hold the “SLIDE (open/close)” switch in the close posi- STEP 3 Check to make sure that the moon roof is completely closed and then release the switch. ● If the moon roof tilts down but then tilts back up STEP 1 Stop the vehicle.
1-4. Opening and closing the windows and moon roof ■ Moon roof open reminder function Vehicles without a smart key system An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the engine switch off. Vehicles with a smart key system An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the “ENGINE START STOP” switch off. ■ Customization that can be configured at Toyota dealer Settings (e.g.
1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicle Vehicles without a smart key system Turn the engine switch off and ensure that all the doors and windows are closed. ■ Opening the fuel tank cap Open the fuel filler door. STEP 1 CTH15AS001 Turn the fuel tank cap slowly to open.
1-5. Refueling Hang the fuel tank cap on the back of the fuel filler door. STEP 3 CTH15AS003 Closing the fuel tank cap After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.
1-5. Refueling CAUTION ■ When refueling the vehicle Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ● Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out the filler neck and cause injury.
1-5. Refueling NOTICE ■ Refueling Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the emission control system to operate abnormally or damaging fuel system components or the vehicle's painted surface.
1-6. Theft deterrent system Engine immobilizer system The vehicle’s keys have built-in transponder chips that prevent the engine from starting if a key has not been previously registered in the vehicle’s on-board computer. 1 Never leave the keys inside the vehicle when you leave the vehicle. The indicator light flashes after the key has been removed from the engine switch to indicate that the system is operating.
1-6. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type engine immobilizer system. ■ Conditions that may cause the system to malfunction ● If the grip portion of the key is in contact with a metallic object ● If the key is in close proximity to or touching a key to the security system (key with a built-in transponder chip) of another vehicle ■ Certifications for the engine immobilizer system (vehicles without a smart key system) ● For vehicles sold in the U.S.A.
1-6. Theft deterrent system CAUTION ■ Certifications for the immobilizer system Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ■ To ensure the system operates correctly Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
1-6. Theft deterrent system Alarm∗ The system sounds the alarm and flashes the lights when forced entry is detected. ■ Triggering of the alarm The alarm is triggered in the following situations when the alarm is set: ● A locked door is unlocked or opened in any way other than using the entry function, wireless remote control or mechanical key. (The doors will lock again automatically.) ● The hood is opened. ■ Setting the alarm system Close the doors and hood, and lock all the doors.
1-6. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type alarm system. ■ Items to check before locking the vehicle To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following: Before driving ● Nobody is in the vehicle. ● The windows and moon roof are closed before the alarm is set. ● No valuables or other personal items are left in the vehicle.
1-6. Theft deterrent system NOTICE ■ To ensure the system operates correctly Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
1-7. Safety information Correct driving posture Drive with a good posture as follows: Sit upright and well back in the seat. (→P. 68) Adjust the seatback so that the controls are easily operable. Adjust the tilt and telescopic positions of the steering wheel downward so the airbag is facing your chest. (→P. 93) Lock the head restraint in place with the center of the head restraint closest to the top of your ears. (→P. 83) Wear the seat belt correctly. (→P.
1-7. Safety information CAUTION ■ While driving ● Do not adjust the position of the driver’s seat. Doing so could cause the driver to lose control of the vehicle. ● Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger. ● Do not place anything under the front seats.
1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.
1-7.
1-7. Safety information Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag system controls airbag deployment power for the driver and front passenger. The driver airbag system consists of the driver’s seat belt buckle switch etc. The front passenger’s airbag system consists of the front passenger occupant classification sensor etc.
1-7. Safety information ■ SRS airbag deployment conditions (SRS front airbags) ● The SRS front airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to an approximately 12 - 18 mph [20 - 30 km/h] frontal collision with a fixed wall that does not move or deform).
1-7. Safety information ■ Conditions under which the SRS airbags may deploy (inflate), other than a collision The SRS front airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration. ● Hitting a curb, edge of pavement or hard surface ● Landing hard or falling CTH17AS150 The SRS curtain shield airbags may also deploy under the situations shown in the illustration. ● The angle of vehicle tip-up is marginal.
1-7. Safety information ■ Types of collisions that may not deploy the SRS airbags (SRS side airbags and curtain shield airbags) The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment.
1-7. Safety information ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ● A portion of a door is damaged or deformed, or the vehicle was involved in an accident that was not severe enough to cause the SRS side airbags and curtain shield airbags to inflate.
1-7. Safety information CAUTION ■ SRS airbag precautions Observe the following precautions regarding the SRS airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts. ● The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag.
1-7. Safety information CAUTION ■ SRS airbag precautions ● The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury especially if the front passenger is very close to the airbag. The front passenger seat should be as far from the airbag as possible with the seatback adjusted, so the front passenger sits upright. ● Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag.
1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not sit on the edge of the seat or lean against the dashboard. CTH17AS015 ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger. ● Do not allow the front seat occupants to hold items on their knees. CTH17AS016 ● Do not lean against the door, the roof side rail or the front and rear pillars.
1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not attach anything to areas such as a door, windshield glass, side door glass, front and rear pillars, roof side rail or assist grip. CTH17AS020 CTH17AS021 ● Vehicles without a smart key system: Do not attach any heavy, sharp or hard objects such as keys and accessories to the key. The objects may restrict the SRS knee airbag inflation or be thrust into the driver's seat area by the force of the deploying airbag, thus causing a danger.
1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not hang coat hangers or other hard objects on the coat hooks. All of these items could become projectiles and may cause death or serious injury, should the SRS curtain shield airbags deploy. ● If a vinyl cover is put on the area where the SRS knee airbag will deploy, be sure to remove it. ● Do not use seat accessories which cover the parts where the SRS side airbags inflate as they may interfere with inflation of the airbags.
1-7. Safety information CAUTION ■ Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury.
1-7. Safety information Deactivating the curtain shield airbags in a vehicle rollover On/off (hold for a few seconds) Vehicles without a smart key system: The “RSCA OFF” indicator turns on. (only when the engine switch is in the “ON” position). CTH17AS084 The roll sensing function for the curtain shield airbags and seat belt pretensioners will turn back on automatically each time the engine switch is turned to the “ON” position. Vehicles with a smart key system: The “RSCA OFF” indicator comes on.
1-7. Safety information CAUTION ■ During normal driving Make sure the “RSCA OFF” indicator light is not turned on. If it is left on, the curtain shield airbags will not activate in the event of an accident, which may cause death or serious injury.
1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classification system. This system detects the conditions of the front passenger seat and activates or deactivates the devices for the front passenger.
1-7.
1-7.
1-7. Safety information ■ There is a malfunction in the system Indicator/ warning light “AIR BAG OFF” SRS warning light On Front passenger's seat belt reminder light Off Front passenger airbag Deactivated Side airbag on the front passenger seat Activated Curtain shield airbag in the front passenger side Activated Front passenger knee airbag Deactivated Front passenger's seat belt pretensioner Activated 1 *1: The system judges a person of adult size as an adult.
1-7. Safety information CAUTION ■ Front passenger occupant classification system precautions Observe the following precautions regarding the front passenger occupant classification system. Failure to do so may cause death or serious injury. ● Wear the seat belt properly. ● Make sure the front passenger’s seat belt plate has not been left inserted into the buckle before someone sits in the front passenger seat.
1-7. Safety information CAUTION ■ Front passenger occupant classification system precautions ● When it is unavoidable to install a forward-facing child restraint system on the front passenger seat, install the child restraint system on the front passenger seat in the proper order. (→P. 146) ● Do not modify or remove the front seats. ● Do not kick the front passenger seat or subject it to severe impact. Otherwise, the SRS warning light may come on to indicate a malfunction of the detection system.
1-7. Safety information Child restraint systems A child restraint system for a small child or baby must itself be properly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems. Points to remember Studies have shown that installing a child restraint on a rear seat is much safer than installing one on the front passenger seat.
1-7. Safety information Forward facing — Convertible seat 1 Before driving CTH17AS144 Booster seat CTH17AS112 ■ Selecting an appropriate child restraint system ● Use a child restraint system appropriate for the child until the child becomes large enough to properly wear the vehicle’s seat belt. ● If the child is too large for a child restraint system, sit the child on a rear seat and use the vehicle’s seat belt. (→P.
1-7. Safety information CAUTION ■ Child restraint precautions ● For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle’s interior.
1-7. Safety information CAUTION ■ Child restraint precautions ● Do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front and rear pillars or roof side rail from which the SRS side airbags or SRS curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the SRS side airbags and SRS curtain shield airbags inflate, and the impact could cause death or serious injury to the child.
1-7. Safety information Installing child restraints Follow the child restraint system manufacturer’s instructions. Firmly secure the child restraints using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Children) system.
1-7. Safety information Seat belts equipped with a child restraint locking mechanism (ALR/ELR belts except driver’s seat belt) (→P. 86) Before driving CTH17AS114 Vehicles without third row seats Anchor brackets (for top tether strap) An anchor bracket is provided for each rear seat. CTH17AS115 Vehicles with third row seats Anchor brackets (for top tether strap) An anchor bracket is provided for each second row seat.
1-7. Safety information Installation with LATCH system (rear/second row seats only) ■ Installing on the rear seats (vehicles without third row seats) Fold the seatback while pulling the seatback angle adjustment lever. Return the seatback and secure it at the first lock position. (→P. 72) STEP 1 CTH17AS116 Type A Latch the hooks of the lower straps onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor.
1-7. Safety information Type B For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system. Canada only CTH17AS118 ■ Installing on the second row seats (vehicles with third row seats) Fold the seatback while pulling the seatback angle adjustment lever. Return the seatback and secure it at the first lock position. (→P. 72) STEP 1 CTH17AS066 STEP 2 Flip the cover.
1-7. Safety information Type A Latch the hooks of the lower straps onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. STEP 3 For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system. Canada only CTH17AS086 Type B Latch the buckles onto the LATCH anchors.
1-7. Safety information Installing child restraints using a seat belt (child restraint lock function belt) ■ Rear facing ⎯ Infant seat/convertible seat CTH17AS119 Run the seat belt through the child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted. STEP 2 CTH17AS140 Fully extend the shoulder belt and allow it to retract to put it in lock mode. In lock mode, the belt cannot be extended.
1-7. Safety information While pushing the child restraint system down into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place. STEP 4 CTH17AS122 After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended. ■ Forward facing ⎯ Convertible seat Place the child restraint system on the seat facing the front of the vehicle.
1-7. Safety information While pushing the child restraint system into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place. STEP 4 STEP 5 If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. (→P. 154) ■ Booster seat Place the child restraint system on the seat facing the front of the vehicle. STEP 1 CTH17AS127 Sit the child in the child restraint system.
1-7. Safety information Removing a child restraint installed with a seat belt Push the buckle release button and fully retract the seat belt. CTH17AS048 Child restraint systems with a top tether strap Secure the child restraint system using a seat belt or the lower anchors, and remove the head restraint.
1-7. Safety information Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top tether strap. STEP 2 1 Make sure the top tether strap is securely latched. Before driving CTH17AS071 Replace the head restraint. STEP 3 CTH17AS130 ■ Laws and regulations pertaining to anchorages The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifications can be used. This vehicle is designed to conform to SAE J1819.
1-7. Safety information CAUTION ■ When installing a booster seat To prevent the belt from going into ALR lock mode, do not fully extend the shoulder belt. ALR mode causes the belt to tighten only. This could cause injury or discomfort to the child. (→P. 88) ■ When installing a child restraint system Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place.
1-7. Safety information CAUTION ■ When installing a child restraint system ● Vehicles with third row seats: When using the LATCH anchors for a child restraint system, move the seat as far back as possible, with the seatback close to the child restraint system. 1 ● When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder. The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder.
1-7. Safety information CAUTION ■ Do not use a seat belt extender If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of sudden braking, sudden swerving or an accident.
2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driving: ■ Starting the engine →P. 170, 173 ■ Driving STEP 1 With the brake pedal depressed, shift the shift lever to D. (→P. 179) STEP 2 Release the parking brake. (→P. 184) STEP 3 Gradually release the brake pedal and gently depress the accelerator pedal to accelerate the vehicle. ■ Stopping STEP 1 With the shift lever in D, depress the brake pedal. STEP 2 If necessary, set the parking brake.
2-1. Driving procedures Starting off on a steep uphill STEP 1 Make sure that the parking brake is set and shift the shift lever to D. STEP 2 Gently depress the accelerator pedal. STEP 3 Release the parking brake. ■ Driving in the rain ● Drive carefully when it is raining, because visibility will be reduced, the windows may become fogged-up, and the road will be slippery.
2-1. Driving procedures ■ Operating your vehicle in a foreign country Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (→P. 636) CAUTION ■ When starting the vehicle Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping. ■ When driving the vehicle ● Do not drive if you are unfamiliar with the location of the brake and accelerator pedals to avoid depressing the wrong pedal.
2-1. Driving procedures CAUTION ● Do not shift the shift lever to P while the vehicle is moving. Doing so can damage the transmission and may result in a loss of vehicle control. ● Do not shift the shift lever to R while the vehicle is moving forward. Doing so can damage the transmission and may result in a loss of vehicle control. ● Do not shift the shift lever to D while the vehicle is moving backward. Doing so can damage the transmission and may result in a loss of vehicle control.
2-1. Driving procedures CAUTION ■ When driving on slippery road surfaces ● Sudden braking, acceleration and steering may cause tire slippage and reduce your ability to control the vehicle, resulting in an accident. ● Sudden changes in engine speed, such as engine braking caused by upshifting or down-shifting, may cause the vehicle to skid, resulting in an accident. ● After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly.
2-1. Driving procedures CAUTION ■ When the vehicle is stopped ● Do not race the engine. If the vehicle is in any gear other than P or N, the vehicle may accelerate suddenly and unexpectedly, causing an accident. ● Do not leave the vehicle with the engine running for a long time. If such a situation cannot be avoided, park the vehicle in an open space and check that exhaust fumes do not enter the vehicle interior.
2-1. Driving procedures CAUTION ● Do not leave a door or window open if the curved glass is coated with a metallized film such as a silver-colored one. Reflected sunlight may cause the glass to act as a lens, causing a fire. ● Always apply the parking brake, shift the shift lever to P, stop the engine and lock the vehicle. Do not leave the vehicle unattended while the engine is running. ● Do not touch the exhaust pipes while the engine is running or immediately after turning the engine off.
2-1. Driving procedures CAUTION ■ When taking a nap in the vehicle Always turn the engine off. Otherwise, if you accidentally move the shift lever or depress the accelerator pedal, this could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.
2-1. Driving procedures NOTICE ■ When driving the vehicle ● Do not depress the accelerator and brake pedals at the same time during driving, as this may restrain driving torque. ● Do not use the accelerator pedal or depress the accelerator and brake pedals at the same time to hold the vehicle on a hill. ■ When parking the vehicle Always shift the shift lever to P. Failure to do so may cause the vehicle to move or the vehicle may accelerate suddenly if the accelerator pedal is accidentally depressed.
2-1. Driving procedures NOTICE ■ When encountering flooded roads Do not drive on a road that has flooded after heavy rain etc.
2-1. Driving procedures Engine (ignition) switch (vehicles without a smart key system) ■ Starting the engine STEP 1 Check that the parking brake is set. STEP 2 Check that the shift lever is set in P. STEP 3 Firmly depress the brake pedal. STEP 4 Turn the engine switch to the “START” position to start the engine. ■ Changing the engine switch positions “LOCK” The steering wheel is locked and the key can be removed. (The key can be removed only when the shift lever is in P.
2-1. Driving procedures ■ Turning the key from “ACC” to “LOCK” STEP 1 Shift the shift lever to P. Push in the key and turn to the “LOCK” position. STEP 2 2 CTH21AS017 The engine immobilizer system may not have been deactivated. (→P. 113) ■ When the steering lock cannot be released When starting the engine, the engine switch may seem stuck in the “LOCK” position. To free it, turn the key while turning the steering wheel slightly left and right.
2-1. Driving procedures CAUTION ■ When starting the engine Always start the engine while sitting in the driver's seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury. ■ Caution when driving Do not turn the engine switch to the “LOCK” position while driving.
2-1. Driving procedures Engine (ignition) switch (vehicles with a smart key system) Performing the following operations when carrying the electronic key on your person starts the engine or changes “ENGINE START STOP” switch modes. ■ Starting the engine STEP 1 Check that the parking brake is set. STEP 2 Check that the shift lever is set in P. STEP 3 Firmly depress the brake pedal. 2 The “ENGINE START STOP” switch indicator will turn green.
2-1. Driving procedures ■ Changing “ENGINE START STOP” switch modes Modes can be changed by pressing the “ENGINE START STOP” switch with brake pedal released. (The mode changes each time the switch is pressed.) Off* The emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can be used. The “ENGINE START STOP” switch indicator turns amber. IGNITION ON mode All electrical components can be used. The “ENGINE START STOP” switch indicator turns amber.
2-1. Driving procedures When stopping the engine with the shift lever in a position other than P If the engine is stopped with the shift lever in a position other than P, the “ENGINE START STOP” switch will not be turned off but instead be turned to ACCESSORY mode. Perform the following procedure to turn the switch off: STEP 1 Check that the parking brake is set. STEP 2 Shift the shift lever to P.
2-1. Driving procedures ■ If the engine does not start The engine immobilizer system may not have been deactivated. (→P. 113) ■ Steering lock After turning the “ENGINE START STOP” switch off and opening and closing the doors, the steering wheel will be locked due to the steering lock function. Operating the “ENGINE START STOP” switch again automatically cancels the steering lock. ■ When the steering lock cannot be released The green indicator light on the “ENGINE START STOP” switch will flash.
2-1. Driving procedures CAUTION ■ When starting the engine Always start the engine while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury. ■ Caution while driving ■ Stopping the engine in an emergency If you want to stop the engine in an emergency while driving the vehicle, press and hold the “ENGINE START STOP” switch for more than 3 seconds.
2-1. Driving procedures NOTICE ■ To prevent battery discharge ● Do not leave the “ENGINE START STOP” switch in ACCESSORY or IGNITION ON mode for long periods of time without the engine running. ● If the indicator on the “ENGINE START STOP” switch is illuminated, the “ENGINE START STOP” switch is not off. When exiting the vehicle, always check that the “ENGINE START STOP” switch is off. ● Do not stop the engine when the shift lever is in a position other than P.
2-1. Driving procedures Automatic transmission Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever 2 When driving CTH21AS014 Vehicles without a smart key system: While the engine switch is in the “ON” position, move the shift lever with the brake pedal depressed. Vehicles with a smart key system: While the “ENGINE START STOP” switch is in IGNITION ON mode, move the shift lever with the brake pedal depressed.
2-1. Driving procedures ■ Shift position purpose Shift position Function P Parking the vehicle/starting the engine R Reversing N Neutral D Normal driving*1 S S mode driving*2 (→P. 181) *1: To improve fuel efficiency and reduce noises, set the shift lever in the D position for normal driving. * 2 : Selecting shift ranges using S mode restricts the upper limit of the possible gear ranges, controls engine braking forces, and prevents unnecessary upshifting.
2-1. Driving procedures Changing shift ranges in S mode When the shift lever is in the S position, the shift lever can be operated as follows: Non-Optitron type meter For upshifting For downshifting 2 When driving CTH21AS025 Optitron type meter For upshifting For downshifting CTH21AS015 The initial shift range in S mode is set automatically to “4” according to vehicle speed. However, the initial shift range may be set to “3” if AI-SHIFT has operated while the shift lever was in the D position. (→P.
2-1. Driving procedures ■ S mode When the shift range is “3” or lower, holding the shift lever toward “+” sets the shift range to “5”. ■ AI-SHIFT AI-SHIFT automatically selects the optimal gear according to driver performance and driving conditions. AI-SHIFT automatically operates when the shift lever is in the D position. (Shifting the shift lever to the S position cancels the function.) The engine speed may remain high after releasing the accelerator pedal. This does not indicate a malfunction.
2-1. Driving procedures Turn signal lever The turn signal lever can be used to show the following intentions of the driver: Right turn Left turn Lane change to the right (push and hold the lever partway) Lane change to the left (push and hold the lever partway) The left hand signals will flash until you release the lever. CTH21AS028 ■ Turn signals can be operated when Vehicles without a smart key system: The engine switch is in the “ON” position.
2-1. Driving procedures Parking brake U.S.A. To set the parking brake, fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot. (Depressing the pedal again releases the parking brake.) Canada CTH21AS031 ■ Usage in winter time See “Winter driving tips” for parking brake usage in winter time. (→P. 288) NOTICE ■ Before driving Fully release the parking brake.
2-1. Driving procedures Horn To sound the horn, press on or close to the mark. 2 CTH21AS022 When driving ■ After adjusting the steering wheel Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P.
2-2.
2-2. Instrument cluster Tachometer Displays the engine speed in revolutions per minute Speedometer Displays the vehicle speed Display change button →P. 188 2 Engine coolant temperature gauge Displays the engine coolant temperature When driving Fuel gauge Displays the quantity of fuel remaining in the tank Eco Driving Indicator Zone Display →P. 189 Odometer, trip meter and average fuel consumption display →P. 188 Shift position and shift range indicators →P.
2-2. Instrument cluster Switching the display Items displayed can be switched by pressing the display change button. ■ Odometer Displays the total distance the vehicle has been driven. ■ Trip meter Displays the distance the vehicle has been driven since the meter was last reset. Trip meters “A” and “B” can be used to record and display different distances independently. Pressing and holding the display change button will reset the trip meter that is currently displayed.
2-2. Instrument cluster ■ Eco Driving Indicator and average fuel consumption Non-Optitron type meter Eco Driving Indicator Light During Eco-friendly acceleration (Eco driving), Eco Driving Indicator Light will turn on.
2-2. Instrument cluster Optitron type meter Eco Driving Indicator Light During Eco-friendly acceleration (Eco driving), Eco Driving Indicator Light will turn on. Eco Driving Indicator Zone Display Suggests Zone of Eco driving with current Eco driving ratio based on acceleration.
2-2. Instrument cluster ■ Eco Driving Indicator Light customization Non-Optitron type meter Eco Driving Indicator Light can be activated or deactivated by pressing and holding the display change button. 2 Eco Driving Indicator Light can be activated or deactivated by pressing and holding the display change button. Instrument panel light control The brightness of the instrument panel lights can be adjusted.
2-2. Instrument cluster ■ The meters and display illuminate when (Optitron type meter) Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode. ■ Eco Driving Indicator Light will not operate in the following conditions ● The shift lever is anything other than D. ● The vehicle speed is approximately 80 mph (130 km/h) or higher.
2-2. Instrument cluster Indicators and warning lights The indicator and warning lights on the instrument cluster and center panel inform the driver of the status of the vehicle’s various systems.
2-2.
2-2. Instrument cluster ■ Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator (→P. 183) Headlight high beam indicator (→P. 207) (if equipped) *1 (if equipped) Tail light indicator (→P. 203) (Canada) (if equipped) Front fog light indicator (→P. 209) Cruise control indicator (→P. 217) (if equipped) (if equipped) Cruise control set indicator (→P. 217) (if equipped) *1, 2 *1 Slip indicator (→P.
2-2. Instrument cluster *1 Crawl Control indicator (→P. 254) Security indicator (→P. 113, 116) Eco Driving Indicator Light (→P. 189) Intuitive parking assist indicator (→P. 221) (if equipped) *1 *1 (if equipped) *1, 2 SRS airbag on-off indicator (→P. 136) (if equipped) Automatic running boards indicator (→P.
2-2. Instrument cluster ■ Warning lights Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 587) *1 (U.S.A.) *1 *1 *1 *1 *2 *1 *3 * 1 * * 1 (Canada) * 1 (U.S.A.) (Canada) *3 *3 *1 *1 (U.S.A.) *3 *4 2 (if equipped) (if equipped) (if equipped) (if equipped) (if equipped) (U.S.A.
2-2. Instrument cluster CAUTION ■ If a safety system warning light does not come on Should a safety system light such as the ABS or SRS warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.
2-2. Instrument cluster Accessory meter The accessory meter presents the driver with a variety of drivingrelated data including the current outside air temperature. 2 When driving “MODE/ “SET/ ” button ” button Trip information (→P. 200) Displays driving range and average fuel consumption Outside temperature display (→P. 457) Compass (→P. 474) Clock (→P. 455) H (Hour) button (→P. 455) M (Minute) button (→P. 455) Multi-terrain Select display (→P.
2-2. Instrument cluster Trip information Items displayed can be switched by pressing the “MODE/ ” button. ■ Driving range Displays the estimated maximum distance that can be driven with the quantity of fuel remaining (vehicles without Multi-terrain Select) • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed. • When only a small amount of fuel is added to the tank, the display may not be updated.
2-2. Instrument cluster Accessory meter light control The daytime brightness of the accessory meter can be adjusted. STEP 1 Turn the headlight switch off. STEP 2 Press and hold the “MODE/ STEP 3 Press the “MODE/ ” button. ” or “SET/ ” button. Vehicles without Multi-terrain Select 2 When driving Vehicles with Multi-terrain Select STEP 4 Press and hold the “SET/ ” button.
2-2. Instrument cluster ■ When the average fuel consumption is reset The average fuel consumption displayed on the instrument cluster and “Past Record” screen of the Display Audio system (if equipped) or the navigation system (if equipped) will be reset at the same time. ■ Adjusting the brightness of the accessory meter ● If left idle for approximately 6 seconds or more while adjusting, the display will revert to the trip information display.
2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. Turning the end of the lever turns on the lights as follows: Type A The daytime running lights turn on. The headlights and all the lights listed above turn on. The daytime running lights turn off. CTH23AS046 203 4RUNNER_U I nf or mat i onPr ovi dedby: 2 When driving The side marker, parking, tail, license plate, daytime running lights and instrument panel lights turn on.
2-3. Operating the lights and wipers Type B The headlights, parking lights, daytime running lights and so on turn on and off automatically (when the “ENGINE START STOP” switch is in IGNITION ON mode). The side marker, parking, tail, license plate, daytime running lights and instrument panel lights turn on. CTH23AS047 The headlights and all the lights listed above turn on. The daytime running lights turn off.
2-3. Operating the lights and wipers Type C The daytime running lights turn on. The side marker, parking, tail, license plate and instrument panel lights turn on. CTH23AS048 205 4RUNNER_U I nf or mat i onPr ovi dedby: When driving The headlights and all the lights listed above turn on.
2-3. Operating the lights and wipers Type D The daytime running lights turn on. The headlights, parking lights, daytime running lights and so on turn on and off automatically (when the “ENGINE START STOP” switch is in IGNITION ON mode). CTH23AS049 The side marker, parking, tail, license plate, daytime running lights and instrument panel lights turn on. The headlights and all the lights listed above turn on.
2-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, push the lever away from you to turn on the high beams. Pull the lever toward you to the center position to turn the high beams off. CTH23AS040 You can flash the high beams with the headlights on or off. ■ Daytime running light system ● To make your vehicle more visible to other drivers, the daytime running lights turn on automatically whenever the engine is started and the parking brake is released.
2-3. Operating the lights and wipers ■ Automatic light off system Vehicles without a smart key system ● When the headlights come on: The headlights and tail lights turn off 30 seconds after a door is opened and closed if the engine switch is turned to the “ACC” or “LOCK” position. (The lights turn off immediately if on the key is pressed after all the doors are locked.
2-3. Operating the lights and wipers Fog light switch The fog lights secure excellent visibility in difficult driving conditions, such as in rain and fog.
2-3. Operating the lights and wipers Type B Turns the front fog lights off Turns the front fog lights on CTH23AS010 ■ Fog lights can be used when The headlights are on in low beam.
2-3. Operating the lights and wipers Windshield wipers and washer When intermittent windshield wiper operation is selected, the wiper interval can be adjusted. The wiper operation is selected by moving the lever as follows.
2-3. Operating the lights and wipers Washer/wiper dual operation The wipers will automatically operate a couple of times after the washer squirts.
2-3. Operating the lights and wipers Washer/wiper dual operation The wipers will automatically operate a couple of times after the washer squirts. 2 CTH23AS029 Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode. ■ If no windshield washer fluid sprays Check that the washer nozzles are not blocked if there is washer fluid in the windshield washer fluid reservoir.
2-3. Operating the lights and wipers Rear window wiper and washer Before operating the rear window wiper and washer switch, make sure the back window is completely closed. (→P. 101) The wiper operation is selected by moving the lever as follows: Type A Intermittent window wiper operation Normal window wiper operation Washer/wiper dual operation Washer/wiper dual operation The wiper will automatically operate a couple of times after the washer squirts.
2-3. Operating the lights and wipers Type B Intermittent window wiper operation Normal window wiper operation Washer/wiper dual operation Washer/wiper dual operation CTH23AS035 ■ The rear window wiper and washer can be operated when ● Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode. ● The back window is completely closed.
2-3. Operating the lights and wipers ■ When the rear window wiper and washer switch is turned off The rear wiper will stop operation, and return to the retracted position after approximately 3 seconds.
2-4. Using other driving systems Cruise control Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicators Cruise control switch 2 ■ Setting the vehicle speed Press the “ON-OFF” button to activate the cruise control. STEP 1 Cruise control indicator will come on. Press the button again to deactivate the cruise control. CTH24AS002 Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set the speed.
2-4. Using other driving systems ■ Adjusting the set speed To change the set speed, operate the lever until the desired set speed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold the lever in the desired direction. CTH24AS004 The set speed will be increased or decreased as follows: Fine adjustment: By approximately 1 mph (1.6 km/h) each time the lever is operated.
2-4. Using other driving systems ■ Cruise control can be set when ● The shift lever is in the D or range 4 or higher of S has been selected. ● Vehicle speed is above approximately 25 mph (40 km/h). ■ Accelerating after setting the vehicle speed ● The vehicle can be accelerated normally. After acceleration, the set speed resumes.
2-4. Using other driving systems CAUTION ■ To avoid operating the cruise control by mistake Switch the cruise control off using the “ON-OFF” button when not in use. ■ Situations unsuitable for cruise control Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury.
2-4. Using other driving systems Intuitive parking assist∗ The distance from your vehicle to nearby obstacles when parallel parking or maneuvering into a garage is measured by the sensors and communicated via an indicator and a buzzer. Always check the surrounding area when using this system.
2-4. Using other driving systems The indicator and buzzer When a sensor detects an obstacle, the direction of the obstacle is indicated and the buzzer sounds. ■ Sensor operation and distance to an obstacle The system operates when the vehicle approaches an obstacle, as shown by the following table. Rear corner sensors Distance to an obstacle ft. (cm) Indicator and buzzer Approximately 1.6 - 1.2 (50 - 37.5) Intermittent Approximately 1.2 - 0.8 (37.5 - 25) Fast intermittent Approximately 0.
2-4. Using other driving systems Detection range of the sensors Approximately 1.6 ft. (50 cm) Approximately 4.9 ft. (150 cm) The diagram shows the detection range of the sensors. Note that the sensors cannot detect obstacles that are extremely close to the vehicle. CTH24AS081 ■ Intuitive parking assist can be operated when Vehicles without a smart key system: The engine switch is in the “ON” position and the shift lever is in R.
2-4. Using other driving systems ■ Sensor detection information ● Certain vehicle conditions and the surrounding environment may affect the ability of a sensor to correctly detect an obstacle. Particular instances where this may occur are listed below. • • • • • • There is dirt, snow or ice on a sensor. A sensor is frozen. A sensor is covered in any way. The vehicle is leaning considerably to one side.
2-4. Using other driving systems ■ When the system malfunctions If a malfunction occurs and no obstacles have been detected, the indicator flashes and the buzzer sounds for approximately 7 seconds. If the indicator comes on and stays on after that, have the vehicle inspected by your Toyota dealer. ■ Customization that can be configured at Toyota dealer Settings (e.g. buzzer volume) can be changed. (Customizable features →P. 660) ■ Certification 2 For vehicles sold in the U.S.A.
2-4. Using other driving systems Rear view monitor system (rear view mirror-attached type)∗ The rear view monitor assists the driver by displaying an image of the area behind the vehicle while reversing. The image is displayed in reverse on the screen. This reversed image is a similar image to the one on the inside rear view mirror. The rear view image is displayed when the shift lever is in R. • If the shift lever is shifted out of R, the screen is turned off.
2-4. Using other driving systems ■ Rear view monitor guide lines 2 CTH24AS077 The guide lines may look different depending on vehicle orientation or road conditions. Vehicle width extension guide lines (blue) These lines indicate the estimated vehicle width extension. Distance guide line (blue) This line indicates a position on the ground about 3 ft. (1 m) behind on the ground of the rear bumper of your vehicle. Distance guide line (red) This line indicates a position on the ground about 1.5 ft. (0.
2-4. Using other driving systems ■ The rear view monitor system can be operated when Vehicles without a smart key system The shift lever is in R, the engine switch is in the “ON” position. Vehicles with a smart key system The shift lever is in R, the “ENGINE START STOP” switch is in IGNITION ON mode. ■ Changing display modes The rear view monitor display mode can be changed while the screen is on. ● To temporarily disable the rear view monitor system Push the “AUTO” button. The indicator will turn amber.
2-4. Using other driving systems ■ Selecting a language (English, French or Spanish) STEP 1 Push and hold the “AUTO” button for 6 to 12 seconds. The screen will turn on and the indicator will turn green. STEP 2 Push the “AUTO” button. CTH24AS080 229 4RUNNER_U I nf or mat i onPr ovi dedby: 2 When driving Each time the “AUTO” switch is pushed, the language changes. Stop pushing the button when the message is displayed in the desired language.
2-4. Using other driving systems ■ Displayed area The area covered by the camera is limited. Objects that are close to either corner of the bumper or under the bumper cannot be seen on the screen. CTH24AS082 The area displayed on the screen may vary depending on vehicle orientation or road conditions.
2-4. Using other driving systems ■ Driving precautions When the grade behind the vehicle slopes up sharply, objects appear to be farther away than they actually are. 2 When the grade behind the vehicle slopes down sharply, objects appear to be closer than they actually are.
2-4. Using other driving systems The distance that appears on the screen between three-dimensional objects (such as vehicles) and flat surfaces (such as the road) and the actual distance differ as follows. In reality, C = A < B (C and A are equally far away; B is farther than C and A). However, on the screen, the situation appears to be A < B < C. CTH24AS086 On the screen, it appears that a truck is parking about 1.5 ft. (0.5 m) away. However, in reality if you back up to point A, you will hit the truck.
2-4. Using other driving systems ● The sun or headlights are shining directly into the camera lens. ● A bright object such as a white wall is reflected in the mirror surface over the monitor. ■ Smear effect If a bright light, such as sunlight reflected off the vehicle body, is picked up by the camera, a smear effect* characteristic to the camera may occur. ■ Flicker effect When the camera is used under fluorescent light, sodium lights, or mercury lights etc.
2-4. Using other driving systems CAUTION ■ When using the rear view monitor system Observe the following precautions to avoid an accident that could result in death or serious injuries: ● Never depend solely on the monitor system when reversing. ● Always check visually and with the mirrors to confirm your intended path is clear.
2-4. Using other driving systems NOTICE ■ Camera precautions ● As the camera has a water proof construction, do not detach, disassemble or modify it. This may cause incorrect operation. ● Do not subject the camera to a strong impact. ● If the camera lens becomes dirty, it cannot transmit a clear image. If water droplets, snow, or mud adhere to the lens, rinse with water and wipe with a soft cloth. If the lens is extremely dirty, wash it with a mild cleanser and rinse. Do not rub hard.
2-4. Using other driving systems Four-wheel drive system (part-time 4WD models) Use the front-wheel drive control lever to select the following transfer modes: CTH24AS015 The four-wheel drive indicator comes on when H4, N or L4 mode is selected. H2 (high speed position, two-wheel drive) Use this for normal driving on dry hard-surfaced roads. This position gives greater economy, quietest ride and least wear.
2-4. Using other driving systems Shifting between H2 and H4 ■ Shifting from H2 to H4 STEP 1 Reduce vehicle speed to less than 50 mph (80 km/h). STEP 2 Shift the front-wheel drive control lever to H4. The four-wheel drive indicator will turn on. ■ Shifting from H4 to H2 Shift the front-wheel drive control lever to H2. This can be done at any speed. 2 When driving The four-wheel drive indicator will go off. Shifting between H4 and L4 STEP 1 Stop the vehicle completely.
2-4. Using other driving systems CAUTION ■ Shifting the front-wheel drive control lever from H2 to H4 while driving Never operate the front-wheel drive control lever if the wheels are slipping. Stop the slipping or spinning before shifting.
2-4. Using other driving systems Four-wheel drive system (full-time 4WD models) Use the four-wheel drive control switch to select the following transfer modes: 2 When driving CTH24AS016 H4F (high speed position) Use this for normal driving on dry hard-surfaced roads. This position gives greater economy, quietest ride and least wear. H4L (high speed position, center differential locked) Use this for driving only on tracks that permit the tires slide, like offroad, icy or snow-covered roads.
2-4. Using other driving systems Shifting between H4F and H4L Push the “UNLOCK” button and turn the four-wheel drive control switch to H4L or H4F. This can be done at any speed. The center differential lock indicator will turn on (H4L) or go off (H4F). CTH24AS017 Shifting between H4L and L4L ■ Shifting from H4L to L4L STEP 1 Stop the vehicle completely. STEP 2 Shift the shift lever to N. Push the “UNLOCK” button and then push and turn the fourwheel drive control switch to L4L.
2-4. Using other driving systems ■ Shifting from L4L to H4L STEP 1 Stop the vehicle completely. STEP 2 Shift the shift lever to N. Push the “UNLOCK” button and turn the four-wheel drive control switch to H4L. STEP 3 Maintain this condition until the low speed four-wheel drive indicator goes off. When driving CTH24AS051 ■ The four-wheel drive control switch can be operated when The “ENGINE START STOP” switch is in IGNITION ON mode.
2-4. Using other driving systems ■ If the low speed four-wheel drive indicator continues to flash and a buzzer sounds The shift lever is not in N and/or the vehicle is moving. Stop the vehicle completely, shift the shift lever to N and make sure that the indicator stops flashing. ■ If the low speed four-wheel drive indicator or the center differential lock indicator flashes rapidly There may be a malfunction in the four-wheel drive system. Have the vehicle inspected by your Toyota dealer immediately.
2-4. Using other driving systems Active traction control system∗ The active traction control system automatically helps prevent the spinning of 4 wheels when the vehicle is started or accelerated on slippery road surfaces. ■ System operation STEP 1 Part-time 4WD models: Stop the vehicle, shift the shift lever to N and shift the frontwheel drive control lever into L4. Press the “A-TRAC” switch to activate the system. STEP 2 At this time, the “A-TRAC” indicator will come on.
2-4. Using other driving systems When the active traction control system is operating If all wheels spin, the slip indicator flashes to indicate that the active traction control system has been engaged. CTH24AS047 ■ When the rear differential is locked (vehicles with a rear differential lock system) The active traction control system is activated only when vehicle speed is less than 4 mph (6 km/h).
2-4. Using other driving systems AUTO LSD system (2WD models) The AUTO LSD system aids traction by using the traction control system to control engine performance and braking when one of the rear wheels begins to spin. The system should be used only when wheel spinning occurs in a ditch or rough surface. ■ System operation Press the VSC off switch to turn on the system. To turn off the system, press the switch again.
2-4. Using other driving systems When the AUTO LSD system is operating If the rear wheels spin, the slip indicator flashes to indicate that the AUTO LSD system has controlled the spinning of the rear wheels. CTH24AS047 ■ If the engine is turned off and restarted The AUTO LSD system and the indicators are automatically turned off. ■ If the brake system overheats The system will cease operation and a buzzer will sound to alert the driver.
2-4. Using other driving systems NOTICE ■ Activating while driving Never activate the AUTO LSD system if the wheel is slipping. Stop the slipping or spinning before activating.
2-4. Using other driving systems Rear differential lock system∗ The rear differential lock system is provided for use only when wheel spinning occurs in a ditch or on a slippery or rugged surface. The rear differential lock system is effective in case one of the rear wheels is spinning. Press the switch to lock the rear differential. At this time, the rear differential lock indicator will flash. Wait a few seconds for the system to complete operation.
2-4. Using other driving systems Using the rear differential lock system STEP 1 Before using the rear differential lock system: Stop the vehicle, shift the shift lever to N and shift the frontwheel drive control lever into L4 to see if this is sufficient. If this has no effect, additionally use the rear differential lock system. STEP 2 Be sure the wheels have stopped spinning. STEP 3 Press the rear differential lock switch. STEP 4 Gently depress the accelerator pedal.
2-4. Using other driving systems CAUTION ■ To avoid an accident ● Do not use the rear differential lock system except when wheel spinning occurs in a ditch or on a slippery or rugged surface. Large steering effort and careful cornering control will be required. ● Do not lock the rear differential until the wheels have stopped spinning. Otherwise, the vehicle may move in an unexpected direction when the differential lock is engaged, resulting in an accident.
2-4. Using other driving systems Downhill assist control system∗ With the downhill assist control system, the vehicle is able to descend a steep hill while maintaining a constant low speed of about 3 mph (5 km/h) without brake pedal operation. ■ Activating the system The system will activate when ● The vehicle is traveling under 15 mph (25 km/h) with the accelerator and brake pedals released. ● The rear differential is unlocked (if equipped). Press the “DAC” switch.
2-4. Using other driving systems While the downhill assist control system is operating The slip indicator will flash to indicate that the downhill assist control system is operating, and the stop lights and high mounted stoplight will turn on. CTH24AS047 ■ Operating tips The system will operate when the shift lever is in any position other than P. However, to make effective use of the system it is recommended that the shift lever be shifted to the “2” or “1” range of S.
2-4. Using other driving systems ■ System malfunction In case of a system malfunction, the following may occur: ● The downhill assist control system indicator flashes in a situation other than those listed above. ● The downhill assist control system indicator does not come on when the engine switch is turned to the “ON” position (vehicles without a smart key system) or the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key system).
2-4. Using other driving systems Crawl Control∗ Allows travel on extremely rough off-road surfaces at a fixed low speed without pressing the accelerator or brake pedal. Minimizes loss of traction or vehicle slip when driving on slippery road surfaces, allowing for stable driving. ■ Crawl Control switch “ON/OFF” switch The Crawl Control indicator comes on and the slip indicator flashes when operating.
2-4. Using other driving systems ■ Speed modes The following table shows some typical terrains and the recommended speed modes. 2 When driving Mode Road condition Rock, mogul (downhill) and gravel (downhill) L (Low) Between L and M Mogul (uphill) M (Medium) Between M and H Snow, mud, gravel (uphill), sand, dirt, mogul (uphill) and grass H (High) ■ Crawl Control can be operated when ● The engine is running. ● The shift lever is in any position other than P or N.
2-4. Using other driving systems ■ Crawl Control is temporarily canceled when Vehicle speed exceeds 15 mph (25 km/h). The Crawl Control indicator flashes until the vehicle speed is reduced. ■ Automatic system cancelation In the following situations, the system will cease operation and a buzzer will sound to alert the driver. The Crawl Control indicator will flash until the system is turned off completely.
2-4. Using other driving systems CAUTION ■ When using Crawl Control ● Do not overly rely on Crawl Control. This function does not extend the vehicle’s performance limitations. Always check the terrain thoroughly and drive safely. ● The recommended speed modes for the listed terrains (→P. 255) are only a reference. The selected mode may not be suitable to actual off-road conditions due to factors such as the type or unevenness of the terrain or the degree of incline.
2-4. Using other driving systems Multi-terrain Select∗ The Multi-terrain Select system has 4 terrain modes. When a terrain mode is selected in accordance with terrain conditions, engine power and active traction control system is controlled to enhance off-road drivability. Additionally, guidance messages such as transfer mode selection advice are displayed on the accessory meter to assist the driver in operating the vehicle.
2-4.
2-4. Using other driving systems The following table shows some typical terrains and the recommended Multi-terrain Select modes. Mode Road condition ROCK MOGUL LOOSE ROCK MUD & SAND Rock Mogul Bump, groove Slope/ V-ditch Uphill/ downhill Riverbed Gravel Bush Deep snow Sand Mud Dirt ■ Multi-terrain Select can be activated when ● Vehicle speed is approximately 7 mph (12 km/h) or less. ● MUD & SAND: The front-wheel drive control lever is in L4 or H4.
2-4. Using other driving systems Selecting modes Press the “ON/OFF” switch. STEP 1 All the mode indicators will come on and then go off except the indicator for the present mode. The applicable road conditions will be displayed on the accessory meter. 2 When driving Turn the dial to select the desired mode. STEP 2 The indicator of the selected mode will come on and the applicable road conditions will be displayed on the accessory meter.
2-4. Using other driving systems Messages displayed on the accessory meter Depending on switch operation, one of the following messages may appear on the accessory meter to provide guidance on transfer mode selection etc: Message Details Procedure SHIFT TO 4WD (When selecting MUD & SAND mode) Indicates that the transfer mode needs to be changed to H4 or L4. Shift the front-wheel drive control lever to H4 or L4.
2-4. Using other driving systems Message Details Procedure CANNOT BE SELECTED (When pressing the “ON/OFF” switch) Indicates that Multiterrain Select cannot be operated because vehicle speed exceeds approximately 7 mph (12 km/h). Reduce vehicle speed. OP. NOT POSSIBLE WHEN CRAWL CONTROL ACTIVATED (When pressing the “ON/OFF” switch) Indicates that Multiterrain Select cannot be operated because Crawl Control is operating.
2-4. Using other driving systems ■ Multi-terrain Select is temporarily canceled when The front-wheel drive control lever is shifted to H4 when Multi-terrain Select is in ROCK, MOGUL or LOOSE ROCK mode. The mode indicator will flash until the lever is shifted back to L4. ■ If the Multi-terrain Select indicator continues to flash This may indicate a malfunction in the Multi-terrain Select system. In this case, Multi-terrain Select is automatically canceled. Have your vehicle inspected by your Toyota dealer.
2-4. Using other driving systems CAUTION ■ Before driving To avoid an accident, observe the precautions relating to off-road driving. (→P. 275) ■ When using Multi-terrain Select ● Do not use the Multi-terrain Select system for normal (on-road) driving. The Multi-terrain Select system is designed for off-road use only. ● The recommended modes for the listed terrains (→P. 259) are only a reference.
2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following systems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle.
2-4.
2-4. Using other driving systems Disabling the TRAC/VSC systems (2WD models) If the vehicle gets stuck in fresh snow or mud, the TRAC/VSC systems may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. ■ Turning off the TRAC system only (turning on the AUTO LSD system [→P. 245]) To turn the TRAC system off, quickly press and release the switch. The VSC off and “AUTO LSD” indicators will come on.
2-4. Using other driving systems ■ Turning off both TRAC and VSC systems To turn the TRAC and VSC systems off, press and hold the switch for more than 3 seconds while the vehicle is stopped. The “TRAC OFF” and VSC off indicators will come on. Press the switch again to turn the systems back on.
2-4. Using other driving systems Disabling the TRAC/VSC systems (4WD models) If the vehicle gets stuck in fresh snow or mud, the TRAC/VSC systems may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. ■ Turning off the TRAC system only To turn the TRAC system off, quickly press and release the switch. The “TRAC OFF” indicator will come on. Press the switch again to turn the system back on.
2-4. Using other driving systems ■ Turning off both TRAC and VSC systems To turn the TRAC and VSC systems off, press and hold the switch for more than 3 seconds while the vehicle is stopped. The “TRAC OFF” and VSC off indicators will come on. Press the switch again to turn the systems back on.
2-4. Using other driving systems ■ When the “TRAC OFF” indicator light comes on even if the VSC off switch has not been pressed TRAC, hill-start assist control, downhill assist control and Crawl Control cannot be operated. Contact your Toyota dealer. ■ Hill-start assist control operation conditions ● The shift lever is in D or S. ● The brake pedal is not depressed. ● The rear differential is unlocked (if equipped).
2-4. Using other driving systems ■ Reactivation of the VSC system linked to vehicle speed (2WD models) When the TRAC system is turned off and the AUTO LSD system is turned on, the VSC system will turn on when vehicle speed increases. However, when the TRAC and VSC systems are turned off, the systems will not turn on even when vehicle speed increases. ■ Reactivation of the TRAC/VSC systems (4WD models) If the TRAC/VSC systems are turned off, the systems will not turn on even when vehicle speed increases.
2-4. Using other driving systems CAUTION ■ When the VSC is activated The slip indicator light flashes. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes. ■ When TRAC/VSC systems are turned off Be especially careful and drive at a speed appropriate to the road conditions. As these are systems to ensure vehicle stability and driving force, do not turn the TRAC/VSC systems off unless necessary.
2-5. Driving information Off-road precautions This vehicle belongs to the utility vehicle class, which has higher ground clearance and narrower tread in relation to the height of its center of gravity to make it capable of performing in a wide variety of off-road applications. Off-road vehicle feature ● An advantage of the higher ground clearance is a better view of the road allowing you to anticipate problems.
2-5. Driving information CAUTION ■ Off-road vehicle precautions Always observe the following precautions to minimize the risk of death, serious injury or damage to your vehicle: ● In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Therefore, the driver and all passengers should fasten their seat belts whenever the vehicle is moving. ● Avoid sharp turns or abrupt maneuvers, if at all possible.
2-5. Driving information Off-road driving When driving your vehicle off-road, please observe the following precautions to ensure your driving enjoyment and to help prevent the closure of areas to off-road vehicles: ● Drive your vehicle only in areas where off-road vehicles are permitted to travel. ● Respect private property. Get owner’s permission before entering private property. 2 ● Do not enter areas that are closed. Honor gates, barriers and signs that restrict travel.
2-5. Driving information CAUTION ■ Off-road driving precautions Always observe the following precautions to minimize the risk of death, serious injury or damage to your vehicle: ● Drive carefully when off the road. Do not take unnecessary risks by driving in dangerous places. ● Do not grip the steering wheel spokes when driving off-road. A bad bump could jerk the wheel and injure your hands. Keep both hands and especially your thumbs on the outside of the rim.
2-5. Driving information NOTICE ■ To prevent water damage Take all necessary safety measures to ensure that water damage to the engine or other components does not occur. ● Water entering the engine air intake will cause severe engine damage. ● Water entering the automatic transmission will cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage.
2-5. Driving information Cargo and luggage Take notice of the following information about storage precautions, cargo capacity and load: ● Stow cargo and luggage in the luggage compartment whenever possible. ● Be sure all items are secured in place. ● To maintain vehicle balance while driving, position luggage evenly within the luggage compartment. ● For better fuel economy, do not carry unnecessary weight.
2-5. Driving information Capacity and distribution Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) — (Total weight of occupants) Steps for Determining Correct Load Limit⎯ (1)Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle's placard. (3)Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs.
2-5. Driving information Example on your vehicle Cargo capacity Total load capacity When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, the available amount of cargo and luggage load capacity will be as follows: Without rear differential lock system Total load capacity: 1165 lb. (525 kg) 1165 lb. - 366 lb. = 799 lb. (525 kg - 166 kg = 359 kg) With rear differential lock system (TRAIL) Total load capacity: 835 lb. (375 kg) 835 lb. - 366 lb. = 469 lb.
2-5. Driving information ■ When using the roof rails Roof rails Cross rails ● To use the roof rails as a roof luggage carrier, you must fit the roof rails with two or more genuine Toyota cross rails or their equivalent.
2-5. Driving information CAUTION ■ Storage precautions Observe the following precautions. Failure to do so may result in death or serious injury. ● Stow cargo and luggage in the luggage compartment whenever possi- ble. ● Do not stack cargo and luggage in the luggage compartment higher than the seatbacks. Such items may be thrown about and possibly injure people in the vehicle in the event of sudden braking or in an accident.
2-5. Driving information CAUTION ■ Roof luggage carrier precautions When you load cargo on the roof luggage carrier, observe the following: ● Place the cargo so that its weight is distributed evenly between the front and rear axles. ● If loading long or wide cargo, never exceed the vehicle overall length or width. (→P. 634) ● Before driving, make sure the cargo is securely fastened on the roof 2 luggage carrier. ity of the vehicle higher.
2-5. Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, trailer weight rating and cargo capacity. ■ Total load capacity Without rear differential lock system: 1165 lb. (525 kg) With rear differential lock system (TRAIL): 835 lb. (375 kg) Total load capacity means the combined weight of occupants, cargo and luggage.
2-5. Driving information CAUTION ■ Overloading the vehicle Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.
2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropriate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are appropriate to the prevailing outside temperatures. • Engine oil • Engine coolant • Washer fluid ● Have a service technician inspect the level and specific gravity of battery electrolyte.
2-5. Driving information ■ Before driving the vehicle Perform the following according to the driving conditions. ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. ● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.
2-5. Driving information Selection tire chains Use the correct tire chain size when mounting the tire chains. Chain size is regulated for each tire size. Side chain (0.20 in. [5 mm] in diameter) Cross chain (0.20 in. [5 mm] in diameter) CTH25AS009 Regulations on the use of tire chains Regulations regarding the use of tire chains vary depending on location and type of road. Always check local regulations before installing chains.
2-5. Driving information CAUTION ■ Driving with snow tires Observe the following precautions to reduce the risk of accidents. Failure to do so may result in a loss of vehicle control and cause death or serious injury. ● Use tires of the size specified. ● Do not drive in excess of 75 mph (120 km/h), regardless of the type of snow tires being used. 2 ● Use snow tires on all, not just some wheels. When driving ● Maintain the recommended level of air pressure.
2-5. Driving information NOTICE ■ Repairing or replacing snow tires Request repairs or replacement of snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the operation of the tire pressure warning valves and transmitters. ■ Fitting tire chains The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.
2-5. Driving information Trailer towing Your vehicle is designed primarily as a passenger-and-load-carrying vehicle. Towing a trailer can have an adverse impact on handling, performance, braking, durability, and fuel consumption. For your safety and the safety of others, you must not overload your vehicle or trailer.
2-5. Driving information Towing related terms ■ GCWR (Gross Combination Weight Rating) CTH25AS029 The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the cargo in the trailer).
2-5. Driving information ■ GAWR (Gross Axle Weight Rating) The maximum allowable gross axle weight. The gross axle weight is the load placed on each axle (front and rear). Front GAWR Rear GAWR 2 When driving CTH25AS031 ■ TWR (Trailer Weight Rating) The maximum allowable gross trailer weight. The gross trailer weight is the sum of the trailer weight and the weight of the cargo in the trailer.
2-5. Driving information ■ Unbraked TWR (Unbraked Trailer Weight Rating) The trailer weight rating for towing a trailer without a trailer service brake system. (Without brakes) CTH25AS020 ■ Tongue Weight The load placed on the trailer hitch ball. (→P.
2-5. Driving information Weight limits ● The gross trailer weight must never exceed the TWR described in the table. (→P. 298) ● The gross combination weight must never exceed the GCWR described in the table. (→P. 298) CTH61AS002 ● The gross axle weight on each axle must never exceed the GAWR indicated on the Certification Label. ● If the gross trailer weight is over the unbraked TWR, trailer service brakes are required. ● If the gross trailer weight is over 2000 lb.
2-5. Driving information GCWR, TWR and Unbraked TWR Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. ■ GCWR* and TWR* Driving system Trailer Weight Rating 2WD 4WD 5000 lb. (2270 kg) GCWR 11100 lb. (5035 kg) 11300 lb. (5125 kg) ■ Unbraked TWR* 1655 lb. (750 kg) *: These models meet the tow-vehicle trailering requirement of SAE International per SAE J2807.
2-5. Driving information Trailer Tongue Weight ● A recommended tongue weight varies in accordance with the types of trailers or towing as described below. ● To ensure the recommended values shown below, the trailer must be loaded by referring to the following instructions. • Tongue Weight Gross trailer weight Tongue weight CTH25AS022 If using a weight distributing hitch when towing, return the front axle to the same weight as before the trailer connection.
2-5. Driving information Hitch Trailer hitch assemblies have different weight capacities. Toyota recommends the use of Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight requirement of your vehicle. ● Follow the directions supplied by the hitch manufacturer. ● Lubricate the hitch ball with a light coating of grease.
2-5. Driving information Selecting trailer ball Use the correct trailer ball for your application. Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Trailer class Typical trailer ball size IV 2 5/16 in. II and III 2 in. I 1 7/8 in. Shank length Protrudes beyond the bottom of the lock washer and nut by at least 2 threads. Shank diameter Matches the ball mount hole diameter size.
2-5. Driving information Positions for towing hitch receiver and hitch ball Weight carrying ball position: 50.1 in. (1272 mm) Hitch receiver pin hole position: 43.7 in. (1109 mm) CTH25AS026 Connecting trailer lights Use the wire harness stored in the rear end under body. CTH25AS011 ■ Service connector for towing brake controller Your vehicle is equipped with a service connector for the trailer brake controller as shown.
2-5. Driving information Trailer towing tips Your vehicle will handle differently when towing a trailer. Help to avoid an accident, death or serious injury, keep the following in mind when towing: ● Speed limits for towing a trailer vary by state or province. Do not exceed the posted towing speed limit. ● Before starting out, check the trailer lights, tires and the vehicletrailer connections. Recheck after driving a short distance.
2-5. Driving information ● Avoid jerky starts or sudden acceleration. ● Avoid jerky steering and sharp turns, and slow down before making turn. ● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a wider than normal turning radius. ● Slow down before making a turn, in cross winds, on wet or slippery surfaces, etc. Increasing vehicle speed can destabilize the trailer. ● Take care when passing other vehicles.
2-5. Driving information ● Always place wheel blocks under both the vehicle’s and the trailer’s wheels when parking. Apply the parking brake firmly, and put the transmission in P. Avoid parking on a slope, but if unavoidable, do so only after performing the following: Apply the brakes and keep them applied. STEP 2 Have someone place wheel blocks under both the vehicle’s and trailer’s wheels. STEP 3 When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load.
2-5. Driving information ■ Matching trailer ball height to trailer coupler height No matter which class of tow hitch applies, for a more safe trailer hookup, the trailer ball setup must be the proper height for the coupler on the trailer. CTH25AS027 Coupler Trailer ball CTH25AS028 ■ Before towing Check that the following conditions are met: ● Ensure that your vehicle’s tires are properly inflated. (→P. 643) ● Trailer tires are inflated according to the trailer manufacturer’s recommendation.
2-5. Driving information ■ Break-in schedule If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota recommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km). After the vehicle has been driven for over 500 miles (800 km), you can start towing.
2-5. Driving information ● After the trailer swaying has stopped: • Stop in a safe place. Get all occupants out of the vehicle. • Check the tires of the vehicle and the trailer. • Check the load in the trailer. Make sure the load has not shifted. Make sure the tongue weight is appropriate, if possible. • Check the load in the vehicle. Make sure the vehicle is not overloaded after occupants get in.
2-5. Driving information CAUTION ● Do not apply the brakes suddenly as you may skid, resulting in jackknifing and loss of vehicle control. This is especially true on wet or slippery surfaces. ● Do not exceed the trailer hitch assembly weight, gross vehicle weight, gross axle weight and trailer tongue weight capacities. ● Do not use cruise control when towing. ● Vehicle-trailer instability is more likely on steep long downhills. Before descending steep or long downhill grades, slow down and downshift.
2-5. Driving information CAUTION ■ When towing a trailer Toyota recommends trailers with brakes that conform to any applicable federal and state/provincial regulations. ● If the gross trailer weight exceeds unbraked TWR, trailer brakes are required. Toyota recommends trailers with brakes that conform to all applicable federal and state/provincial regulations. ● Never tap into your vehicle’s hydraulic system, as this will lower the vehicle’s braking effectiveness.
2-5. Driving information Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. 2 When driving NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground.
3-1. Using the air conditioning system and defogger Manual air conditioning system∗ Outside/recirculated air mode button Air outlet selector knob Cooling and dehumidification function on/off button Fan speed control knob Temperature control knob Adjusting the settings ■ Basic setting STEP 1 To turn on the air conditioning system and adjust the fan speed, turn the fan speed control knob clockwise (increase) or counterclockwise (decrease). Turning the knob to “OFF” turns off the fan.
3-1. Using the air conditioning system and defogger STEP 2 To adjust the temperature setting, turn the temperature control knob clockwise (warm) or counterclockwise (cool). If is not pressed, the system will blow ambient temperature air or heated air. For quick cooling, turn the temperature control knob to “MAX A/C”. The air conditioning will automatically turn on and, if an air outlet position other than or is selected, the system will be set to recirculated air mode.
3-1. Using the air conditioning system and defogger Air flows to the feet. CTH31AS006 Air flows to the feet and the windshield defogger operates. The air intake is automatically switched to outside air mode. Pressing CTH31AS007 to turn the cool- ing and dehumidification function on clears the windshield and side windows faster. Air flows to the windshield and side windows. The air intake is automatically switched to outside air mode.
3-1. Using the air conditioning system and defogger ■ Switching between outside air and recirculated air modes Press . The mode switches between outside air mode (introduces air from outside the vehicle) (indicator off) and recirculated air mode (recycles air inside the vehicle) (indicator on) each time the button is pressed. Adjusting the position of and opening and closing the air outlets Front center outlets Direct air flow to the left or right, up or down.
3-1. Using the air conditioning system and defogger Rear outlets Direct air flow to the left or right, up or down. Turn the knob to open or close the vent. CTH31AS016 ■ Using the system in recirculated air mode The windows will fog up more easily if recirculated air mode is used for an extended period of time. ■ Switching between outside air and recirculated air modes Recirculated air mode or outside air mode may be automatically switched to in accordance with the outside temperature, etc.
3-1. Using the air conditioning system and defogger ■ Air conditioning odors ● During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents. ● To reduce potential odors from occurring: It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off.
3-1. Using the air conditioning system and defogger Automatic air conditioning system∗ Air outlets and fan speed are automatically adjusted according to the temperature setting.
3-1. Using the air conditioning system and defogger Using the automatic air conditioning system STEP 1 Press . The air conditioning system begins to operate. Air outlets and fan speed are automatically adjusted according to the temperature setting. STEP 2 Turn clockwise to increases the temperature and turn counterclockwise to decreases the temperature on the 3 driver’s side.
3-1. Using the air conditioning system and defogger Adjusting the settings manually ■ Basic setting STEP 1 To turn on the air conditioning system and adjust the fan speed, press “>” on to increase the fan speed and “<” to decrease the fan speed. Press STEP 2 to turn the fan off. To adjust the temperature setting, turn clockwise to increases the temperature and turn counterclockwise to decreases the temperature.
3-1. Using the air conditioning system and defogger Air flows to the upper body and feet. CTH31AS010 Air flows to the feet. 3 Air flows to the feet and the windshield defogger operates. The air intake is automatically switched to outside air mode.
3-1. Using the air conditioning system and defogger ■ Switching between outside air and recirculated air modes Press . The mode switches between outside air mode (the indicator is off) and recirculated air mode (the indicator is on) each time the button is pressed. Defogging the windshield Defogging The air conditioning system operates automatically. The air intake is automatically switched to outside air mode. It is not possible to return to recirculated air mode when the switch is on.
3-1. Using the air conditioning system and defogger Adjusting the position of and opening and closing the air outlets Front center outlets Direct air flow to the left or right, up or down. Turn the knob to open or close the vent. CTH31AS014 Front side outlets 3 Turn the knob to open or close the vent. CTH31AS015 Rear outlets Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.
3-1. Using the air conditioning system and defogger ■ Using automatic mode Fan speed is adjusted automatically according to the temperature setting and ambient conditions. As a result, the following may occur: ● The system may switch automatically to recirculated air mode when the coolest temperature setting is selected when the ambient temperature is high. ● Immediately after the switch is pressed, the fan may stop for a while until warm or cool air is ready to flow.
3-1. Using the air conditioning system and defogger ■ When outside air temperature is below 32°F (0°C) The cooling and dehumidification function may not operate even when is pressed. ■ When the indicator light on flashes to turn off the cooling and dehumidification function and turn it Press on again. There may be a problem in the air conditioning system if the indicator light continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer.
3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers Defoggers are used to defog the rear window, and to remove raindrops, dew and frost from the outside rear view mirrors. Before operating the defoggers, make sure the back window is completely closed. (→P. 101) Vehicles with a manual air conditioning system Turns the defoggers on/off The defoggers will automatically turn off after their operation time.
3-1. Using the air conditioning system and defogger ■ The defoggers can be operated when ● Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode. ● The back window is completely closed. ■ The outside rear view mirror defoggers Turning the rear window defogger on will turn the outside rear view mirror defoggers on.
3-1. Using the air conditioning system and defogger Windshield wiper de-icer∗ This feature is used to prevent ice from building up on the windshield and wiper blades. Turns the windshield wiper deicer on/off The windshield wiper de-icer will automatically turn off after approximately 15 minutes. CTH31AS020 ■ The windshield wiper de-icer can be operated when Vehicles without a smart key system The engine switch is in the “ON” position.
3-2.
3-2. Using the audio system Type C: CD player with changer and AM/FM radio Title Page Using the radio P. 338 Using the CD player P. 345 Playing MP3 and WMA discs P. 354 Operating an iPod P. 362 Operating a USB memory P. 369 Optimal use of the audio system P. 376 Using the AUX port P. 381 Using the steering wheel audio switches P.
3-2. Using the audio system With Display Audio system Owners of models equipped with a Display Audio system should refer to the “Display Audio System Owner's Manual”. 3 Owners of models equipped with a navigation system should refer to the “Navigation System Owner's Manual”.
3-2. Using the audio system Language settings (type B and C) The language used for all voice guidance, voice recognition and messages may be changed. STEP 1 Press . STEP 2 Press (MORE). STEP 3 Press (LANG). STEP 4 Press guage. or as corresponds to the desired lan- For vehicles sold in the U.S.A.
3-2. Using the audio system ■ Certification For the Display Audio system FCC ID: AJDK032 IC ID: 775E-K032 The antenna for Bluetooth cannot be removed (or replaced) by user. L'antenne de Bluetooth ne peut pas être supprimé (ou remplacé) par l'utilisateur. This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. Cet appareil est conforme au CNR-310 d'Industrie Canada.
3-2. Using the audio system CAUTION: This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE).
3-2. Using the audio system Co-location: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. CAUTION ■ For vehicles sold in the U.S.A. and Canada ● Part 15 of the FCC Rules and RSS-Gen of the IC Rules FCC Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
3-2.
3-2. Using the audio system Setting station presets (excluding XM® Satellite Radio) STEP 1 Search for desired stations by turning pressing “∧” or “∨” on STEP 2 or or . Press and hold a button (from a beep. to ) until you hear Type B and C: Each time is pressed, station pages are changed. There are a total of 6 pages. 3 Scanning radio stations (excluding XM® Satellite Radio) STEP 1 Press and hold until you hear a beep. Preset stations will be played for 5 seconds each.
3-2. Using the audio system XM® Satellite Radio (if equipped) ■ Receiving XM® Satellite Radio STEP 1 Press . or The display changes as follows each time pressed. or is Type A: AM → SAT1 → SAT2 → SAT3 Type B and C: AM → FM → SAT STEP 2 Turn or to select the desired channel in all the categories or press “∧” or “∨” on to select the desired channel in the current category. ■ Setting XM® Satellite Radio channel presets Select the desired channel.
3-2. Using the audio system ■ Scanning XM® Satellite Radio channels ● Scanning channels in the current category STEP 1 Press STEP 2 When the desired channel is reached, press again. . ● Scanning the preset channels STEP 1 Press and hold STEP 2 When the desired channel is reached, press again. until you hear a beep. ■ Displaying text information Press 3 . Type B and C: Title (song/program title) → Name (artist name/feature)/ Title (song/program title).
3-2. Using the audio system ■ When the battery is disconnected All preset stations are erased. (type A only) ■ Reception sensitivity ● Type B and C ⎯ Cargo loaded on the roof luggage carrier, especially metal objects, may adversely affect the reception of XM® Satellite Radio. ● Maintaining perfect radio reception at all times is difficult due to the continually changing position of the antenna, differences in signal strength and surrounding objects, such as trains, transmitters, etc.
3-2. Using the audio system ■ If XM® Satellite Radio does not operate normally If a problem occurs with the XM® tuner, a message will appear on the display. Refer to the table below to identify the problem, and take the suggested corrective action. ANTENNA or CHECK ANTENNA There is a short-circuit in the antenna or the surrounding antenna cable. See a Toyota certified dealer. You have not subscribed to XM® Satellite Radio. The radio is being updated with the latest encryption code.
3-2. Using the audio system --or CHANNEL NOT AVAILABLE The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel. Contact the XM® Listener Care Center at 1-800-967-2346 (U.S.A.
3-2.
3-2. Using the audio system Loading CDs ■ Loading a CD (type A and B) Insert a CD. ■ Loading a CD (type C) STEP 1 Press STEP 2 When the indicator on the slot turns from amber to green, insert a CD. . ■ Loading multiple CDs (type C only) STEP 1 Press and hold STEP 2 When the indicator on the slot turns from amber to green, insert a CD. until you hear a beep. The indicator on the slot turns to amber when the CD is inserted.
3-2. Using the audio system Ejecting CDs ■ Ejecting a CD (type A and B) Press and remove the CD. ■ Ejecting a CD (type C) STEP 1 To select the CD to be ejected, press ( ( ) or ). The selected CD number is shown on the display. STEP 2 Press and remove the CD. ■ Ejecting all the CDs (type C only) Press and hold the CDs. until you hear a beep, and then remove Press “∧” to move up or “∨” to move down using until the desired track number is displayed.
3-2. Using the audio system Scanning tracks STEP 1 Press . The first ten seconds of each track will be played. To cancel, press STEP 2 Press again. again when the desired track is reached. Selecting a CD (type C only) ■ Selecting a CD to play Press ( ) or ( ). ■ Scanning loaded CDs STEP 1 Press and hold until you hear a beep. The first ten seconds of the first track on each CD will be played. To cancel, press STEP 2 Press again. again when the desired CD is reached.
3-2. Using the audio system Random playback ■ Current CD Press (RAND) or (RDM). Songs are played in random order. To cancel, press the button once more (type A and B), or twice more (type C). ■ All CDs (type C only) Press (RDM) twice. Tracks on all loaded CDs are played in random order. To cancel, press the button again. 3 ■ Repeating a track Press (RPT) or (RPT). To cancel, press the button once more (type A and B), or twice more (type C).
3-2. Using the audio system Switching the display Press . Each time order: is pressed, the display changes in the following Type A: Track no./Elapsed time → CD title → Track name. Type B and C: Track title → Track name/Artist name → Track name/ Elapsed time. ■ Display (type A only) Up to 12 characters can be displayed at a time. If there are 13 characters or more, pressing and holding ond or more will display the remaining characters. A maximum of 24 characters can be displayed.
3-2. Using the audio system ■ Error messages “CD CHECK”: This indicates a problem either with the CD or inside the player. The CD may be dirty, damaged or inserted up-side down. “WAIT” or “PLEASE WAIT”: Operation has stopped due to a high temperature inside the player. Wait for a while and then press or . Contact your Toyota dealer if the CD still cannot be played back. ■ Discs that can be used Discs with the marks shown below can be used.
3-2. Using the audio system NOTICE ■ CDs and adapters that cannot be used Do not use the following types of CDs, 3 in. (8 cm) CD adapters or Dual Discs. Doing so may damage the CD player and/or the CD insert/eject function. ● CD player with changer and AM/FM radio: CDs that have a diameter that is not 4.7 in.
3-2. Using the audio system NOTICE ■ CD player precautions Failure to follow the precautions below may result in serious damage to the CDs or the player itself. ● Do not insert anything other than CDs into the CD slot. ● Do not apply oil to the CD player. ● Store CDs away from direct sunlight. ● Never try to disassemble any part of the CD player. ● Do not insert more than one CD at a time.
3-2.
3-2. Using the audio system Loading and ejecting MP3 and WMA discs →P. 346 Selecting MP3 and WMA discs (type C only) →P. 347 Selecting and scanning a folder ■ Selecting folders one at a time Press “∧” or “∨” on to select the desired folder. 3 ■ Scanning the first file of all the folders Press and hold Interior features STEP 1 until you hear a beep. The first ten seconds of the first file in each folder will be played. STEP 2 When the desired folder is reached, press again.
3-2. Using the audio system ■ Selecting the desired file by cueing the files in the folder Press . When the desired file is reached, press once again. Fast-forwarding and rewinding files Type A: Press ( ) or ( ). Type B and C: Press and hold “∧” or “∨” on . Playing and pausing files (type B and C) Press . Random playback ■ Playing files from a particular folder in random order Press (RAND) or (RDM). To cancel, press the button once more (type A and B), or twice more (type C).
3-2. Using the audio system Repeat play ■ Repeating a file Press (RPT) or (RPT). To cancel, press the button once more (type A and B), or twice more (type C). ■ Repeating all of the files in a folder Type A: Press and hold Type B and C: Press (RPT) until you hear a beep. (RPT) twice. To cancel, press the button once more (type A and B), or twice more (type C). 3 ■ Repeating all of the files in a disc (type C only) Interior features Press (RPT) three times. To cancel, press the same button again.
3-2. Using the audio system ■ Display (type A only) →P. 350 ■ Error messages “CD CHECK”: This indicates a problem either with the CD or inside the player. The CD may be dirty, damaged or inserted up-side down. “WAIT” or “PLEASE WAIT”: Operation has stopped due to a high temperature inside the player. Wait for a while and then press or . Contact your Toyota dealer if the CD still cannot be played. ■ Discs that can be used →P. 351 ■ CD player protection feature →P.
3-2. Using the audio system ■ MP3 and WMA files MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression. WMA (Windows Media Audio) is a Microsoft audio compression format. This format compresses audio data to a size smaller than that of the MP3 format. There is a limit to the MP3 and WMA file standards that can be used and to the media/formats on which the files are recorded.
3-2. Using the audio system ● Compatible media Media that can be used for MP3 and WMA playback are CD-Rs and CDRWs. Playback in some instances may not be possible if the CD-R or CD-RW is not finalized. Playback may not be possible or the audio may jump if the disc is scratched or marked with fingerprints. ● Compatible disc formats The following disc formats can be used.
3-2. Using the audio system ● MP3 and WMA playback When a disc containing MP3 or WMA files is inserted, all files on the disc are first checked. Once the file check is finished, the first MP3 or WMA file is played. To make the file check finish more quickly, we recommend you do not write in any files other than MP3 or WMA files or create any unnecessary folders. If the discs contain a mixture of music data and MP3 or WMA format data, only music data can be played. ● Extensions If the file extensions .
3-2. Using the audio system Operating an iPod∗ Connecting an iPod enables you to enjoy music from the vehicle speakers. ■ Connecting an iPod Open the glove box and connect an iPod using an iPod cable. STEP 1 Turn on the power of the iPod if it is not turned on. CTH32AS081 STEP 2 Press .
3-2.
3-2. Using the audio system Selecting a play mode STEP 1 Press STEP 2 Press , , desired play mode. (BROWSE) to select iPod menu mode. Pressing or as corresponds to the (MORE) to change to the second selection list.
3-2. Using the audio system ■ Selecting a list STEP 1 Turn STEP 2 Press STEP 3 Repeat the same procedure to select the desired song name. to display the first selection list. to select the desired item. To return to the previous selection list, press ( ). Selecting songs from a song list STEP 1 Press 3 (LIST). Interior features The current playlist is displayed. STEP 2 Turning Press to select the desired song. returns the screen from list display to the previous screen.
3-2. Using the audio system Selecting songs Turn or press “∧” or “∨” on to select the desired song. Playing and pausing songs Press . Fast-forwarding and rewinding songs Press and hold “∧” or “∨” on . Shuffle playback ■ Playing songs from one playlist or album in random order Press (RDM). To cancel, press the button twice. ■ Playing songs from all the playlists or albums in random order Press (RDM) twice. To cancel, press the button again. Repeat play Press (RPT).
3-2. Using the audio system Switching the display Press . Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time ■ About iPod ● Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. ● iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
3-2. Using the audio system ■ Compatible models Model Generation Software version iPod 5th generation Ver. 1.2.0 or higher iPod nano 1st generation Ver. 1.3.0 or higher 2nd generation Ver. 1.1.2 or higher 3rd generation Ver. 1.0.0 or higher iPod touch 1st generation Ver. 1.1.0 or higher iPod classic 1st generation Ver. 1.0.0 or higher Depending on differences between models or software version etc., some models listed above might be incompatible with this system.
3-2. Using the audio system Operating a USB memory∗ Connecting a USB memory enables you to enjoy music from the vehicle speakers. ■ Connecting a USB memory Open the glove box and connect a USB memory. STEP 1 Turn on the power of the USB memory if it is not turned on. 3 Interior features CTH32AS081 STEP 2 Press .
3-2. Using the audio system ■ Control panel Power Volume Selector knob Selecting a track/ fast-forwarding and rewinding Selecting a folder and file Selector buttons Searching playback Playback/pause Displaying text messages Playback Selecting and scanning a folder ■ Selecting a folder Press “∧” or “∨” on to select the desired folder. ■ Returning to the first file of the first folder Press and hold “∨” on until you hear a beep.
3-2. Using the audio system Selecting and scanning files ■ Selecting a file Turn or press “∧” or “∨” on to select the desired file. ■ Scanning the files in a folder Press . The first ten seconds of each file will be played. To cancel, press again. When the desired file is reached, press 3 again. Interior features Playing and pausing files Press . Fast-forwarding and rewinding files Press and hold “∧” or “∨” on . Random playback ■ Playing files from a folder in random order Press (RDM).
3-2. Using the audio system Repeat play ■ Repeating a file Press (RPT). To cancel, press the button twice. ■ Repeating all the files in a folder Press (RPT) twice. To cancel, press the button again. Switching the display Press .
3-2. Using the audio system ■ USB memory ● Compatible device USB memories that can be used for MP3 and WMA playback. Depending on the type of USB device, playback may not be possible. ● Compatible device formats The following device formats can be used: • USB communication formats: USB2.
3-2. Using the audio system ● MP3 file compatibility • Compatible standards MP3 (MPEG1 AUDIO LAYERII, III, MPEG2 AUDIO LAYERII, III, MPEG2.5) • Compatible sampling frequencies MPEG1 AUDIO LAYERII, III: 32, 44.1, 48 (kHz) MPEG2 AUDIO LAYERII, III: 16, 22.05, 24 (kHz) MPEG2.5: 8, 11.025, 12 (kHz) • Compatible bit rates (compatible with VBR) MPEG1 AUDIO LAYERII, III: 32-320 (kbps) MPEG2 AUDIO LAYERII, III: 32-160 (kbps) MPEG2.
3-2. Using the audio system ● Extensions If the file extensions .mp3 and .wma are used for files other than MP3 and WMA files, they will be mistakenly recognized and played as MP3 and WMA files. This may result in large amounts of interference and damage to the speakers. ● Playback • To play MP3 file with steady sound quality, we recommend a fixed bit rate of at least 128 kbps and a sampling frequency of 44.1 kHz.
3-2.
3-2. Using the audio system Using the audio control function ■ Changing sound quality modes Type A Pressing selects the mode to be changed in the following order: “BAS”→“TRE”→“FAD”→“BAL”→“ASL” Type B and C STEP 1 Press STEP 2 Press , , , or (type C only) as corresponds to the desired mode. “BASS”, “MID” (type C only), “TREB”, “FADE”, or “BAL” . 3 Turning or adjusts the level.
3-2. Using the audio system Type B and C Mode displayed Sound quality mode Level Turn to the left Turn to the right BASS Bass* -5 to 5 MID Mid-range* (type C only) -5 to 5 Low High TREB Treble* -5 to 5 FADE Front/rear volume balance F7 to R7 Shifts to rear Shifts to front BAL Left/right volume balance L7 to R7 Shifts to left Shifts to right *: The sound quality level is adjusted individually in each audio mode.
3-2. Using the audio system Type B and C STEP 1 Press STEP 2 Press (MORE). STEP 3 Press (ASL). STEP 4 Press , , (type B only) or only) as corresponds to the desired mode. . (type B Type B: “LOW”, “MID”, “HIGH”, or “OFF” Type C: “ON” or “OFF” ASL automatically adjusts the volume and tone quality according to vehicle speed. ■ Setting the number of preset pages (type B and C) STEP 1 Press . STEP 2 Press (MORE). STEP 3 Press (PRESET).
3-2. Using the audio system Party mode switch You can switch the sounds quality types by pressing the switch. Base mode Party mode In party mode, the sound volume from the speakers on the back door is bigger than in base mode. (The output from the speakers on the rear doors will be transferred to the back door speakers.) CTH32AS048 ■ Trademark owned by SRS Labs, Inc.
3-2. Using the audio system Using the AUX port This port can be used to connect a portable audio device and listen to it through the vehicle’s speakers. Open the cover and connect the portable audio device. STEP 1 3 Interior features CTH32AS023 STEP 2 Press or . ■ Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle's audio controls. All the other adjustments must be made on the portable audio device itself.
3-2. Using the audio system Using the steering wheel audio switches∗ Some audio features can be controlled using the switches on the steering wheel.
3-2. Using the audio system Turning the power on Press when the audio system is turned off. The audio system can be turned off by holding the switch down until you hear a beep. Changing the audio source Press when the audio system is turned on. The audio source changes as follows each time the switch is pressed. If no discs are inserted in the player, that mode will be skipped. FM→SAT→CD (type B only)→CD changer (type C only)→Bluetooth® Audio→AUX→USB/iPod→AM Press “+” on volume.
3-2. Using the audio system Selecting a track/file or song STEP 1 Press to select CD, iPod, USB memory or Bluetooth® audio mode. STEP 2 Press “∨” or “∧” on song. to select the desired track/file or Selecting a folder or album STEP 1 Press to select the CD, USB memory or Bluetooth® audio mode. STEP 2 Press and hold “∨” or “∧” on until you hear a beep. Selecting a disc in the CD player (type C only) STEP 1 Press STEP 2 Press and hold “∨” or “∧” on to select CD mode. until you hear a beep.
3-2. Using the audio system Detachable pole antenna The antenna can be removed. ■ Removing the antenna Place the included wrench around the antenna. STEP 1 When not in use, the wrench is stored in glove box. CTH32AS077 Loosen the antenna with the wrench and remove it.
3-2. Using the audio system ■ Installing the antenna Tighten the antenna by one hand until it will not turn any more. STEP 1 CTH32AS079 Using the wrench, tighten the antenna an additional 1/8th turn (20 to 45 degrees) to secure it in place. STEP 2 After tightening the antenna, remove the wrench. CTH32AS080 ■ About the wrench After using the included wrench, store it in the glove box for safekeeping.
3-2. Using the audio system NOTICE ■ To avoid damaging the antenna Remove the antenna in the following situations. ● When using an automatic carwash. ● When the antenna will touch the ceiling of a garage, etc. ● When covering the vehicle with a car cover. ■ Removing the antenna ● For normal driving, make sure the antenna is installed. ● When removing the antenna to use an automatic carwash, etc., be careful not to lose the antenna. Also, make sure to reinstall the antenna before driving the vehicle.
3-3. Using the Bluetooth® audio system Bluetooth® audio system∗ The Bluetooth® audio system enables you to enjoy music played on a portable digital audio player (portable player) from the vehicle speakers via wireless communication. This audio system supports Bluetooth®, a wireless data system capable of playing portable audio music without cables. If your portable player does not support Bluetooth®, the Bluetooth® audio system will not function.
3-3. Using the Bluetooth® audio system ■ About Bluetooth® Bluetooth is a registered trademark of Bluetooth SIG. Inc. ■ Compatible models ● Bluetooth® specifications: Ver. 1.2 ● Following Profiles: 3 ■ Certification for the Bluetooth® audio system FCC ID: AJDK025 AJDK032 IC ID: 775E-K025 775E-K032 MADE IN JAPAN This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s).
3-3. Using the Bluetooth® audio system CAUTION ■ FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio Frequency Radiation Exposure. This equipment complies with FCC/ IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
3-3. Using the Bluetooth® audio system Using the Bluetooth® audio system ■ Audio unit Display Track title, Artist name, Album name, Elapsed time, “Streaming Audio”, etc. is displayed. Selects items such as menu and number Turn: Selects an item Press: Inputs the selected item Bluetooth-Audio tion condition connec- ■ Microphone CTH33AS001 391 4RUNNER_U I nf or mat i onPr ovi dedby: Interior features If “BT” is not displayed, the Bluetooth® audio system cannot be used.
3-3. Using the Bluetooth® audio system Operating the system using voice commands By following voice guidance instructions output from the speaker, voice commands enable to the operation of the Bluetooth® audio system without the need to check the display or operate . ■ Operation procedure when using voice commands Press the talk switch and follow voice guidance instructions.
3-3. Using the Bluetooth® audio system Using the Bluetooth® audio system for the first time Before using the Bluetooth® audio system, it is necessary to register a Bluetooth® enabled portable player in the system. Follow the procedure below to register (pair) a portable player: STEP 1 Press and hold STEP 2 Press until “BT AUDIO” is displayed. (SETUP). The introductory guidance and portable player name registration instructions are heard.
3-3. Using the Bluetooth® audio system STEP 6 Input the passkey into the portable player. Refer to the manual that comes with the portable player for the operation of the portable player. Guidance for registration completion is heard. If the portable player has a Bluetooth® phone, the phone can be registered at the same time. (→P.
3-3. Using the Bluetooth® audio system ■ When using a voice command For numbers, say a combination of single digits from zero to nine. Say the command correctly and clearly.
3-3. Using the Bluetooth® audio system Operating a Bluetooth® enabled portable player Power Volume Selecting a track/ fast-forwarding and reversing Selector knob Selecting an album Playback Playback/pause Selecting an album Press “∨” or “∧” on . Selecting tracks Press “∧” or “∨” on . Playing and pausing tracks Press .
3-3. Using the Bluetooth® audio system Fast-forwarding and reversing tracks Press and hold “∧” or “∨” on . Switching the display Press . Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time 3 Using the steering wheel audio switches ■ Bluetooth® audio system functions Depending on the portable player that is connected to the system, certain functions may not be available.
3-3. Using the Bluetooth® audio system Setting up a Bluetooth® enabled portable player Registering a portable player in the Bluetooth® audio system allows the system to function. The following functions can be used for registered portable players: ■ Functions and operation procedures STEP 1 Press and hold STEP 2 Press STEP 3 Select one of the following functions using a voice command or until “BT AUDIO” is displayed. (SETUP). .
3-3. Using the Bluetooth® audio system Registering a portable player Select “Pair Audio Players (Pair audio player)” using a voice command or , and perform the procedure for registering a portable player. (→P. 393) Selecting a portable player to be used STEP 1 Select “Select Audio Player” using a voice command or . Select the portable player to be used by either of the following methods, and select “Confirm” using a voice command or : a.
3-3. Using the Bluetooth® audio system STEP 3 Press the talk switch and say “From car” or “From audio”, and select “Confirm” using a voice command or . Vehicles with smart key system: If “From car” is selected, the portable player will be automatically connected whenever the “ENGINE START STOP” switch is in either ACCESSORY or IGNITION ON mode.
3-3. Using the Bluetooth® audio system Listing the registered portable players Select “List Audio Players” using a voice command or . The list of registered portable players will be read aloud. When listing is complete, the system returns to “BT Audio Setup”.
3-3. Using the Bluetooth® audio system Deleting a registered portable player STEP 1 Select “Delete Audio Player” using a voice command or . STEP 2 Select the portable player to be deleted by either of the following methods and select “Confirm” using a voice command or : a. Press the talk switch and say the name of the desired portable player. b. Press the talk switch and say “List audio players”. When the name of the desired portable player is read aloud, press the talk switch.
3-3. Using the Bluetooth® audio system Bluetooth® audio system setup ■ System setup items and operation procedures →P.
3-4. Using the hands-free phone system (for cellular phone) Hands-free phone system (for cellular phone) features∗ This system supports Bluetooth®, which allows you to make or receive calls without using cables to connect a cellular phone and the system, and without operating the cellular phone. Owners of models equipped with a Display Audio system should refer to the “Display Audio System Owner's Manual”.
3-4. Using the hands-free phone system (for cellular phone) Title Page Using the hands-free phone system ■ Operating the system using a voice command ■ Using the hands-free phone system for the first time ■ Menu list of the hands-free phone system P. 409 Making a phone call ■ Dialing by inputting a number ■ Dialing by inputting a name ■ Speed dialing ■ When receiving a phone call ■ Transferring a call ■ Using the call history memory P.
3-4.
3-4. Using the hands-free phone system (for cellular phone) ■ Certification for the hands-free phone system FCC ID: AJDK025 AJDK032 IC ID: 775E-K025 775E-K032 MADE IN JAPAN 407 4RUNNER_U I nf or mat i onPr ovi dedby: 3 Interior features This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s).
3-4. Using the hands-free phone system (for cellular phone) CAUTION ■ FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio Frequency Radiation Exposure. This equipment complies with FCC/ IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
3-4. Using the hands-free phone system (for cellular phone) Using the hands-free phone system (for cellular phone) ■ Audio unit Display A message, name, phone number, etc. is displayed. Lower-case characters and special characters, such as an umlaut, cannot be displayed. Selects speed dials Bluetooth® connection condition and reception level If “BT” is not displayed, the hands-free phone system cannot be used.
3-4. Using the hands-free phone system (for cellular phone) ■ Steering wheel switches Volume The voice guidance volume cannot be adjusted using this button.
3-4. Using the hands-free phone system (for cellular phone) Operating the system using a voice command By following voice guidance instructions output from the speaker, voice commands enable the operation of the hands-free phone system without the need to check the display or operate . ■ Operation procedure when using a voice command Press the talk switch and follow voice guidance instructions.
3-4. Using the hands-free phone system (for cellular phone) STEP 2 Select “Pair Phone” using a voice command or STEP 3 Register a phone name by either of the following methods. a. Select “Record Name” using . , and say a name to be registered. b. Press the talk switch and say a name to be registered. A voice guidance instruction to confirm the input is heard. STEP 4 Select “Confirm” using a voice command or .
3-4.
3-4.
3-4.
3-4. Using the hands-free phone system (for cellular phone) ■ Automatic volume adjustment When vehicle speed reaches 50 mph (80 km/h) or more, the volume automatically increases. The volume returns to the previous volume setting when vehicle speed drops to 43 mph (70 km/h) or less. ■ When using a voice command For numbers, say a combination of single digits from zero to nine, # (pound), ∗ (star), and + (plus). Say a command correctly and clearly.
3-4.
3-4. Using the hands-free phone system (for cellular phone) Dialing by inputting a name STEP 1 Press the talk switch and say “Dial by name”. STEP 2 Select a registered name to be input by either of the following methods: a. Press the talk switch and say a registered name. b. Press the talk switch and say “List names”. Press the talk switch while the desired name is being read aloud. STEP 3 Dial by one of the following methods: a. Press the off-hook switch. b. Press the talk switch and say “Dial”. c.
3-4. Using the hands-free phone system (for cellular phone) Transferring a phone call A call can be transferred between the cellular phone and system while dialing, receiving a call, or during a call. Use one of the following methods: a. Operate the cellular phone. Refer to the manual that comes with the cellular phone for the operation of the phone. b. Press the off-hook switch*1. c. Press the talk switch and say “Call transfer”*2.
3-4. Using the hands-free phone system (for cellular phone) The following operations can be performed: Dialing: Press the off-hook switch or select “Dial” using a voice command or . Storing the number in the phone book: Select “Store” using a voice command or . Deleting: Select “Delete” using a voice command or . ■ Call history Up to 5 numbers can be stored in each of the outgoing and incoming call history memories. ■ When talking on the phone ● Do not talk at the same time as the other party.
3-4. Using the hands-free phone system (for cellular phone) Setting a cellular phone Registering a cellular phone in the hands-free phone system allows the system to function. The following functions can be used for registered cellular phones: ■ Functions and operation procedures To enter the menu for each function, follow the steps below using a voice command or : ● Registering a cellular phone 1. “Setup (Setup)” → 2. “Phone Setup” → 3. “Pair Phone” ● Selecting the cellular phone to be used 1.
3-4. Using the hands-free phone system (for cellular phone) Selecting the cellular phone to be used STEP 1 Select “Select Phone” using a voice command or . Pattern A STEP 2 Select the cellular phone to be used by either of the following methods, and select “Confirm” using a voice command or : a. Press the talk switch and say the desired phone name. b. Press the talk switch and say “List phones”. While the name of the desired cellular phone is being read aloud, press the talk switch.
3-4. Using the hands-free phone system (for cellular phone) STEP 2 Select the name of the cellular phone to be changed by either of the following methods: a. Press the talk switch and say the desired phone name, and select “Confirm” using a voice command or . b. Press the talk switch and say “List phones”. While the desired phone name is being read aloud, press the talk switch. c. Select the desired phone name using .
3-4. Using the hands-free phone system (for cellular phone) Deleting a cellular phone STEP 1 Select “Delete Phone” using a voice command or STEP 2 Select the cellular phone to be deleted by either of the following methods and select “Confirm” using a voice command or . : a. Press the talk switch and say the name of the desired cellular phone. b. Press the talk switch and say “List phones”. While the name of the desired cellular phone is being read aloud, press the talk switch.
3-4. Using the hands-free phone system (for cellular phone) Turning the hands-free phone automatic connection on/off ■ Turning off the automatic connection STEP 1 Select “Handsfree Power” using a voice command or STEP 2 Select “Turn off” using a voice command or . . ■ Turning on the automatic connection Select “Handsfree Power” using a voice command or STEP 2 Select “Turn on” using a voice command or . .
3-4. Using the hands-free phone system (for cellular phone) Security and system setup To enter the menu of each setting, follow the steps below: ■ Security setting items and operation procedure ● Setting or changing the PIN (Personal Identification Number) 1. “Setup (Setup)” → 2. “Security” → 3. “Set PIN” ● Locking the phone book 1. “Setup (Setup)” → 2. “Security” → 3. “Phonebook Lock (Phone book lock)” ● Unlocking the phone book 1. “Setup (Setup)” → 2. “Security” → 3.
3-4. Using the hands-free phone system (for cellular phone) STEP 2 Enter a PIN using a voice command or When using . , input the code 1 digit at a time. ■ Changing the PIN STEP 1 Select “Set PIN” using a voice command or STEP 2 Enter the registered PIN using a voice command or STEP 3 Enter a new PIN using a voice command or . . , input the code 1 digit at a time.
3-4. Using the hands-free phone system (for cellular phone) Setting voice guidance volume STEP 1 Select “Guidance Volume” using STEP 2 Change the voice guidance volume. To decrease the volume: Turn . counterclockwise. To increase the volume: Turn clockwise. Initialization STEP 1 Select “Reset Settings” and then “Confirm” using STEP 2 Select “Confirm” using 428 4RUNNER_U I nf or mat i onPr ovi dedby: . .
3-4. Using the hands-free phone system (for cellular phone) ■ Initialization ● The following data in the system can be initialized: • Phone book • Outgoing and incoming call history • Speed dials • Registered cellular phone data • Security code ● Once the initialization has been completed, the data cannot be restored to its original state.
3-4. Using the hands-free phone system (for cellular phone) Using the phone book To enter the menu of each setting, follow the steps below: ● Adding a new phone number 1. “Phonebook” → 2. “Add Entry” ● Setting speed dial 1. “Phonebook” → 2. “Speed Dial (Set speed dial)” ● Changing a registered name 1. “Phonebook” → 2. “Change Name” ● Deleting registered data 1. “Phonebook” → 2. “Delete Entry” ● Deleting speed dial 1. “Phonebook” → 2. “Delete Speed Dial” ● Listing the registered data 1. “Phonebook” → 2.
3-4. Using the hands-free phone system (for cellular phone) ■ Adding procedure STEP 1 Select “Add Entry” using a voice command or STEP 2 Use one of the following methods to input a telephone number: . Inputting a telephone number using a voice command STEP2-1 Select “By Voice (By voice)” using a voice command or . STEP2-2 Press the talk switch, say the desired number, and select “Confirm” using a voice command. STEP2-1 Select “By Phone” and then “Confirm” using a voice command or .
3-4. Using the hands-free phone system (for cellular phone) Inputting a phone number using STEP2-1 Select “Manual Input” using STEP2-2 Input a phone number using . , and press once again. Input the phone number 1 digit at a time. Selecting a phone number from outgoing or incoming call history STEP2-1 Select “Call History” using a voice command or . STEP2-2 Select “Outgoing Call History (Outgoing)” or “Incoming Call History (Incoming)” using a voice command or .
3-4. Using the hands-free phone system (for cellular phone) STEP 3 Select the name to be registered by either of the following methods, and select “Confirm” using a voice command or : a. Press the talk switch and say the desired name. b. Select “Record Name” using , and say the desired name. STEP 4 Select “Confirm” using a voice command or .
3-4. Using the hands-free phone system (for cellular phone) Setting speed dials STEP 1 Select “Speed Dial (Set speed dial)” using a voice command or STEP 2 . Select the data to be registered as a speed dial by either of the following methods: a. Press the talk switch, say desired number, and select “Con. firm” using a voice command or b. Press the talk switch, and say “List names”. While the desired name is being read aloud, press the talk switch, and select “Confirm” using a voice command or c.
3-4. Using the hands-free phone system (for cellular phone) Changing a registered name STEP 1 Select “Change Name” using a voice command or STEP 2 Select the name to be changed by either of the following methods. . a. Press the talk switch, say desired name, and select “Confirm” using a voice command or . b. Press the talk switch, and say “List names”. While the desired name is being read aloud, press the talk switch, c.
3-4. Using the hands-free phone system (for cellular phone) Deleting registered data STEP 1 Select “Delete Entry” using a voice command or STEP 2 Select the data to be deleted by either of the following methods, and select “Confirm” using a voice command or . : a. Press the talk switch, and say the name of the desired phone number to be deleted. b. Press the talk switch, say “List phones”. While the name of the desired phone number is being read aloud, press the talk switch.
3-4. Using the hands-free phone system (for cellular phone) Listing the registered data Selecting “List names” using a voice command causes a list of the registered data to be read aloud. When listing is complete, the system returns to “Phonebook”. Pressing the talk switch while the desired data is being read aloud selects the data, and the following function will be available.
3-5. Using the interior lights Interior lights list CTH35AS003 Rear interior light (→P. 439) Front personal lights/front interior light (→P.
3-5.
3-5. Using the interior lights Personal lights ■ Illuminated entry system Vehicles without a smart key system The lights automatically turn on/off according to the engine switch position, whether the doors are locked/unlocked, and whether the doors are open/ closed. Vehicles with a smart key system The lights automatically turn on/off according to “ENGINE START STOP” switch mode, the presence of the electronic key, whether the doors are locked/unlocked, and whether the doors are open/closed.
3-6.
3-6. Using the storage features Glove box CAUTION ■ Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: ● Glasses may be deformed by heat or cracked if they come into contact with other stored items. ● Lighters or spray cans may explode. If they come into contact with other stored items, the lighter may catch fire or the spray can may release gas, causing a fire hazard.
3-6. Using the storage features Console box Console box Lift the lid while pulling up the knob to release the lock. CTH36AS011 ■ The separator can be used in either of the positions shown in the illustration Interior features Change the separator position. CTH36AS012 CAUTION ■ Caution while driving Keep the console box closed. In the event of sudden braking, an accident may occur due to an occupant being struck by the open console box or the items stored inside.
3-6. Using the storage features Coin holder Coin holder Lift the lid while pulling up the knob to release the lock. CTH36AS013 CAUTION ■ Caution while driving Keep the console box closed. In the event of sudden braking, an accident may occur due to an occupant being struck by the open console box or the items stored inside.
3-6. Using the storage features Tissue pocket Tissue pocket Lift the lid while pulling up the knob to release the lock. 3 Interior features CTH36AS014 CAUTION ■ Caution while driving Keep the console box closed. In the event of sudden braking, an accident may occur due to an occupant being struck by the open console box or the items stored inside.
3-6. Using the storage features Pen holder Pen holder Lift the lid while pulling up the knob to release the lock. CTH36AS015 CAUTION ■ Caution while driving Keep the console box closed. In the event of sudden braking, an accident may occur due to an occupant being struck by the open console box or the items stored inside.
3-6. Using the storage features Auxiliary box Auxiliary box (if equipped) Push the lid. CTH36AS016 CAUTION 3 ■ Caution while driving ■ Items unsuitable for storing Do not store items heavier than 0.4 lb. (0.2 kg). Doing so may cause the auxiliary box to open and the items inside may fall out, resulting in an accident. 447 4RUNNER_U I nf or mat i onPr ovi dedby: Interior features Keep the auxiliary box closed.
3-6. Using the storage features Cup holders Cup holders Front seats CTH36AS009 Rear seats (without third row seats) Pull down the rear seat center armrest. CTH36AS005 Second row seats (with third row seats) Pull down the second row seat center armrest and press down the button on the armrest.
3-6. Using the storage features Cup holders Third row seats (if equipped) CTH36AS020 ■ Adjusting the size of the cup holders Front seats 3 Remove the adapter. Interior features CTH36AS010 Rear seats (without third row seats) Remove the adapter.
3-6. Using the storage features Cup holders CAUTION ■ Items unsuitable for the cup holder Do not place anything other than cups or beverage cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking, causing injury. If possible, cover hot drinks to prevent burns. ■ When not in use (second row seat cup holders only) Keep the cup holders closed.
3-6. Using the storage features Bottle holders Bottle holders Front seats CTH36AS018 Rear seats (without third row seats)/Second row seats (with third row seats) 3 Interior features CTH36AS019 ■ When using the bottle holder ● When storing a bottle, close the cap. ● The bottle may not be stored depending on its size or shape. CAUTION ■ Items unsuitable for the bottle holder Do not place anything other than a bottle in the bottle holders.
3-6. Using the storage features Bottle holders NOTICE ■ Items that should not be stowed in the bottle holders Put the cap on before stowing a bottle. Do not place open bottles in the bottle holders, or glasses and paper cups containing liquid. The contents may spill and glasses may break.
3-7. Other interior features Sun visors To set the visor in the forward position, flip it down. To set the visor in the side position, flip down, unhook, and swing it to the side. CTH37AS007 To use the side extender, place the visor in the side position, then slide it backward.
3-7. Other interior features Vanity mirrors Slide the cover to open. The light turns on when the cover is opened. CTH37AS008 NOTICE ■ To prevent battery discharge Do not leave the vanity lights on for extended periods while the engine is off.
3-7.
3-7. Other interior features ■ For quicker adjustment of the clock To advance the minutes and hours quickly, press and hold the “M” or “H” button. The time can be adjusted back or forth by following the procedure below: The hour or minute can be moved forward or backward by pressing the “MODE/ ” or “SET/ ” button while pressing and holding the “H” or “M” button. If the “MODE/ ” or “SET/ ” button is also pressed and held in the above operation, the hour or minute will move faster.
3-7. Other interior features Outside temperature display The temperature display shows temperatures within the ranges of -40°F (-40°C) and 122°F (50°C).
3-7. Other interior features Vehicles with Multi-terrain Select ■ The outside temperature is displayed when Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.
3-7. Other interior features ■ ICE indicator Vehicles without Multi-terrain Select If the outside temperature lowers to 37°F (3°C) or below when the engine switch is in the “ON” position (vehicles without a smart key system) or the “ENGINE START STOP” switch is in IGNITION ON mode (vehicles with a smart key system), the “ICE” indicator will come on to warn the driver that roads may be icy. Check the road surface and drive carefully.
3-7. Other interior features Power outlets (12 V DC) The power outlet can be used for 12 V accessories that run on less than 10 A.
3-7.
3-7. Other interior features Luggage compartment (vehicles with the 120 V AC) CTH37AS086 ■ The power outlet can be used when Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode. NOTICE ■ To avoid damaging the power outlet Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short circuit.
3-7. Other interior features Power outlets (120 V AC)∗ The power outlet can be used for electrical appliances. Main switch To use the power outlet, turn on the main switch. The power supply starts a few seconds after the main switch is pressed.
3-7. Other interior features Power outlet socket (luggage compartment) CTH37AS087 Maximum available capacity of the power outlet ■ While the vehicle is being driven The maximum capacity of the power outlet is always 120 V AC/100 W. ■ When the vehicle is stationary The maximum capacity of the power outlet varies depending on the position of the shift lever. ● The maximum capacity is 120 V AC/100 W when the shift lever is in any position other than P or N.
3-7. Other interior features ■ The power outlet can be used when The engine is running. ■ The indicator light changes according to the maximum available capacity as follows: 120 V AC/400 W 120 V AC/100 W CTH37AS025 3 ■ When the power outlet is in operation ■ If the engine is started with the power outlet main switch on The maximum capacity of the power supply may decrease to below the standard, or may be cut off completely, even when the vehicle is stationary.
3-7. Other interior features ■ If the protection circuit is activated and the power supply is cut, conduct the following procedure: STEP 1 Park the vehicle in a safe place, and then securely apply the park- ing brake. STEP 2 Check and ensure that the shift lever is in P or N. STEP 3 Make sure that the power consumption of the electric appliance is within the maximum capacity of the power outlet and the appliance is not broken. STEP 4 Press the power outlet main switch again.
3-7. Other interior features CAUTION ■ Using a power outlet Observe the following precautions to reduce the risk of injury. ● Use of the power outlet when it is wet with water or snow may result in electrical shocks and is extremely dangerous. The power outlet must be thoroughly dried before use. ● Do not allow children to use or play with the power outlet. ● Be careful not to get any part of your body caught in the power outlet lid.
3-7. Other interior features NOTICE ■ To avoid damaging the power outlet and the plug ● Close the power outlet lid when not in use. ● Do not allow foreign objects or liquids to enter the power outlet, as this may cause a short circuit. ● Do not use plug adaptors to connect too many plugs to the power outlet. ● After removing a plug, gently close the power outlet lid. ■ To prevent the fuse from being blown Do not use a 120 V AC appliance that requires more than the maximum capacity of the power outlet.
3-7. Other interior features NOTICE ■ If any electrical appliances are to be used while driving Securely fasten both the appliances and their cables to prevent them from falling or getting caught in any of the power train components. ■ If the power outlet is loose when an electrical appliance plug is connected Replace the outlet. Contact your Toyota dealer for any necessary replacements. ■ If the power outlet gets dirty Turn the main switch off and use a soft, clean cloth to wipe it gently.
3-7. Other interior features Seat heaters∗ On Front passenger’s seat The indicator light comes on. Adjusts the seat temperature Driver’s seat The further you move the dial forward, the warmer the seat becomes. CTH37AS005 ■ The seat heaters can be used when Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. ■ When not in use Move the dial fully backward. The indicator light turns off.
3-7. Other interior features CAUTION ■ Burns ● Use caution when seating the following persons in a seat with the seat heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the physically challenged • Persons with sensitive skin • Persons who are fatigued • Persons who have taken alcohol or drugs that induce sleep (sleeping drugs, cold remedies, etc.) ● Do not cover the seat with anything when using the seat heater.
3-7. Other interior features Armrest Fold down the armrest for use. CTH37AS088 NOTICE ■ To prevent damage to the armrest Do not apply too much load on the armrest.
3-7. Other interior features Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Fix the floor mat in place using the retaining hooks (clips) provided. The shape of the retaining hooks (clips) and the fixing procedure of the floor mat for your vehicle may differ from those shown in the illustration. For details, refer to the floor mat retention clip installation instructions supplied with the clips.
3-7. Other interior features Compass The compass on the accessory meter display indicates the direction in which the vehicle is heading.
3-7. Other interior features Calibrating the compass 3 Samoa: 5 Guam: 8 Saipan: 8 CTH37AS072 If you cross over one of the map boundaries shown in illustration, the compass will deviate. To obtain higher precision or perfect calibration, refer to “Deviation calibration”. 475 4RUNNER_U I nf or mat i onPr ovi dedby: Interior features The direction display deviates from the true direction determined by the earth’s magnetic field.
3-7. Other interior features Deviation calibration STEP 1 Stop the vehicle. STEP 2 Change the accessory meter display to deviation calibration mode by doing the following. Vehicles without Multi-terrain Select When the parking lights are turned on: Press and hold the “MODE/ ” button. A number (1 to 15) will appear on the display. When the parking lights are off: In accessory meter light control mode (→P. 201), press and hold the “MODE/ ” button. A number (1 to 15) will appear on the display.
3-7. Other interior features STEP 3 Referring to the map above, press the “MODE/ ” or “SET/ ” button to select the number of the zone you are in. STEP 4 Press and hold the “SET/ ” button to confirm the number and to exit deviation calibration mode. (If the button is pressed for more than 6 seconds, the number will automatically be confirmed and the display returned to normal.) Circling calibration If “•” appears on the left side of the direction display, circling calibration needs to be performed.
3-7. Other interior features Drive the vehicle in a circle completing at least one full circle within 20 - 120 seconds. STEP 3 If there is not enough space to drive in a circle, drive around the block until a direction is displayed. STEP 4 Press and hold the “SET/ ” button to confirm the direction and to exit circling calibration mode. (If the button is pressed for several minutes, the direction will automatically be confirmed and the display returned to normal.
3-7. Other interior features ■ Circling calibration error message (vehicles with Multi-terrain Select) In the following situations, an error message regarding the circling calibration will appear on the accessory meter display for a few seconds: ● The vehicle was driven too fast during the circling calibration. ● The circling calibration was not completed successfully within about two minutes.
3-7. Other interior features Luggage compartment features ■ Cargo hooks Vehicles with third seats STEP 1 Fold down the third seats. (→P. 79) Raise the hook to use. STEP 2 The cargo hooks are provided for securing loose items. CTH37AS041 Vehicles without third seats Raise the hook to use. The cargo hooks are provided for securing loose items.
3-7. Other interior features ■ Cargo net hooks The cargo net itself is not included as original equipment. Vehicles with third seats (pattern 1) Raise the rear cargo hook to use. CTH37AS075 3 Vehicles with third seats (pattern 2) Fold down the third seats. (→P. 79) Interior features STEP 1 Raise the cargo hook to use. STEP 2 CTH37AS076 Vehicles without third seats (pattern 1) Raise the rear cargo hook to use.
3-7. Other interior features Vehicles without third seats (pattern 2) Raise the cargo hook to use. CTH37AS091 ■ Storage compartment Type A (if equipped) Open the storage compartment as shown. CTH37AS014 Type B (if equipped) Open the storage compartment as shown.
3-7. Other interior features ■ Slide deck (if equipped) Slide the deck while turning the lock release lever, and then release the lever after sliding the deck to the lock position.
3-7. Other interior features Type B (if equipped) To use the grocery bag hooks, slide the slide deck to the fullslide locked position. (→P. 483) CTH37AS095 CAUTION ■ When the cargo hooks are not in use To avoid injury, always return the cargo hooks to their stowed positions. ■ Slide deck operating precaution (if equipped) ● Be careful not to get hands or feet pinched by the slide deck. ● Be careful not to allow the slide deck to hit any persons or luggage while sliding the deck.
3-7. Other interior features NOTICE ■ To prevent damage to the cargo net hooks Avoid hanging things other than a cargo net on them. ■ Slide deck weight capacity (if equipped) Do not load anything heavier than 440 lb. (200 kg) on the sliding deck. ■ Grocery bag hook weight capacity Do not hang any object heavier than 8.8 lb. (4 kg) on the grocery bag hooks. ■ When using the slide deck (if equipped) ● Do not close the back door while the slide deck is sliding out.
3-7. Other interior features Garage door opener The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, security systems, and other devices. The garage door opener (HomeLink® Universal Transceiver) is manufactured under license from HomeLink®. Programming HomeLink® (for U.S. owners) The HomeLink® compatible transceiver in your vehicle has 3 buttons which can be programmed to operate 3 different devices.
3-7. Other interior features ■ Programming HomeLink® Point the remote control transmitter for the device 1 to 3 in. (25 to 75 mm) from the HomeLink® buttons. STEP 1 Keep the HomeLink® indicator light in view while programming. 487 4RUNNER_U I nf or mat i onPr ovi dedby: 3 Interior features Press and hold one of the HomeLink® buttons and the transmitter button. When the HomeLink® indicator light changes from a slow to a rapid flash after 20 seconds, release both buttons.
3-7. Other interior features Test the HomeLink® operation by pressing the newly programmed button. STEP 3 If a HomeLink® button has been programmed for a garage door, check to see if the garage door opens and closes. If the garage door does not operate, see if your garage transmitter is of the rolling code type. Press and hold the programmed HomeLink® button. The remote control transmitter is of the rolling code type if the HomeLink® indicator light flashes rapidly for 2 seconds and then remains lit.
3-7. Other interior features ■ Programming a rolling code system (for U.S. owners) If your device is rolling code equipped, follow the steps under the heading “Programming HomeLink®” before proceeding with the steps listed below. STEP 1 Locate the learn button on the ceiling mounted garage door opener motor. The exact location and color of the button may vary by brand of garage door opener. Refer to the operation manual supplied with the garage door opener for the location of the learn button.
3-7. Other interior features ■ Programming an entry gate (for U.S. owners)/Programming a device in the Canadian market STEP 1 Place the remote control transmitter 1 to 3 in. (25 to 75 mm) away from the HomeLink® buttons. Keep the HomeLink® indicator light in view while programming. STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 Press and hold the selected HomeLink® button. Repeatedly press and release (cycle) the remote control transmitter for 2 seconds each until step 4 is completed.
3-7. Other interior features Operating HomeLink® Press the appropriate HomeLink® button. The HomeLink® indicator light should come on. The HomeLink® compatible transceiver in your vehicle continues to send a signal for up to 20 seconds as long as the button is pressed. Erasing the entire HomeLink® memory (all three programs) Press and hold the 2 outside buttons for 20 seconds until the indicator light flashes. 3 ■ Before programming ● Install a new battery in the remote control transmitter.
3-7. Other interior features ■ Certification for the garage door opener For vehicles sold in the U.S.A. FCC ID: CB2300NHL3 NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
3-7. Other interior features Safety Connect∗ Safety Connect is a subscription-based telematics service that uses Global Positioning System (GPS) data and embedded cellular technology to provide safety and security features to subscribers. Safety Connect is supported by Toyota’s designated response center, which operates 24 hours per day, 7 days per week. Safety Connect service is available by subscription on select, telematics hardware-equipped vehicles.
3-7. Other interior features ■ Services Subscribers have the following Safety Connect services available: ● Automatic Collision Notification* Helps drivers receive necessary response from emergency service providers. (→P. 496) *: U.S. Patent No. 7,508,298 B2 ● Stolen Vehicle Location Helps drivers in the event of vehicle theft. (→P. 497) ● Emergency Assistance Button (SOS) Connects drivers to response-center support. (→P. 497) ● Enhanced Roadside Assistance Provides drivers various on-road assistance.
3-7. Other interior features ■ Safety Connect Services Information ● Phone calls using the vehicles Bluetooth® technology will not be possible during Safety Connect. ● Safety Connect is available beginning Fall 2009 on select Toyota models.
3-7. Other interior features Safety Connect LED light Indicators When the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key system) or the engine switch is turned to the “ON” position (vehicles without a smart key system), the red indicator light comes on for 2 seconds then turns off. Afterward, the green indicator light comes on, indicating that the service is active.
3-7. Other interior features ■ Stolen Vehicle Location If your vehicle is stolen, Safety Connect can work with local authorities to assist them in locating and recovering the vehicle. After filing a police report, call the Safety Connect response center at 1800-331-4331 and follow the prompts for Safety Connect to initiate this service.
3-7. Other interior features Safety information for Safety Connect Important! Read this information before using Safety Connect. ■ Exposure to radio frequency signals The Safety Connect system installed in your vehicle is a low-power radio transmitter and receiver. It receives and also sends out radio frequency (RF) signals. In August 1996, the Federal Communications Commission (FCC) adopted RF exposure guidelines with safety levels for mobile wireless phones.
3-7.
3-7.
4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition: ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust. ● Wash the vehicle body using a sponge or soft cloth, such as a chamois. ● For hard-to-remove marks, use car wash soap and rinse thoroughly with water. ● Wipe away any water.
4-1. Maintenance and care ■ Aluminum wheels (if equipped) ● Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint. ● Do not use detergent on the wheels when they are hot, for example after driving for long distance in the hot weather. ● Wash detergent from the wheels immediately after use. ■ Bumpers and side moldings Do not scrub with abrasive cleaners.
4-1. Maintenance and care NOTICE ■ To prevent paint deterioration and corrosion on the body and components (aluminum wheels etc.
4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle’s interior and keep it in top condition: ■ Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces with a cloth dampened with lukewarm water. ■ Cleaning the leather areas ● Remove dirt and dust using a vacuum cleaner. ● Wipe off any excess dirt and dust with a soft cloth dampened with diluted detergent.
4-1. Maintenance and care ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not use water. Wipe dirty surfaces and let them dry. Excellent results are obtained by keeping the carpet as dry as possible.
4-1. Maintenance and care NOTICE ■ Cleaning detergents ● Do not use the following types of detergent, as they may discolor the vehicle interior or cause streaks or damage to painted surfaces: • Non-seat portions: Organic substances such as benzene or gasoline, alkaline or acidic solutions, dye, and bleach. • Seats: Alkaline or acidic solutions, such as thinner, benzene, and alcohol. ● Do not use polish wax or polish cleaner. The instrument panel’s or other interior part’s painted surface may be damaged.
4-2. Maintenance Maintenance requirements To ensure safe and economical driving, day-to-day care and regular maintenance are essential. It is the owner’s responsibility to perform regular checks. Toyota recommends performing the following maintenance: ■ General maintenance General maintenance should be performed on a daily basis. This can be done by yourself or by a Toyota dealer.
4-2. Maintenance ■ Reset the maintenance data (U.S.A. only) After the required maintenance is performed according to the maintenance schedule, please reset the maintenance data. To reset the data, follow the procedures described below: STEP 1 Switch the display to the trip meter A (→P. 188) when the engine is running. STEP 2 Vehicles without a smart key system Turn the engine switch off. Vehicles with a smart key system Turn the “ENGINE START STOP” switch off.
4-2. Maintenance CAUTION ■ If your vehicle is not properly maintained Improper maintenance could result in serious damage to the vehicle and possible serious injury or death. ■ Handling of the battery ● Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.
4-2. Maintenance General maintenance Listed below are the general maintenance items that should be performed at the intervals specified in the “Owner's Warranty Information Booklet” or “Owner’s Manual Supplement/Scheduled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items Check points Check the connections. (→P.
4-2. Maintenance Vehicle interior Items Check points Accelerator pedal • The accelerator pedal should move smoothly (without uneven pedal effort or catching).
4-2. Maintenance Items Check points Parking brake • Does the parking brake pedal move smoothly? • When parked on a slope and the parking brake is on, is the vehicle securely stopped? Seat belts • Do the seat belts operate smoothly? • The seat belts should not be damaged.
4-2. Maintenance Vehicle exterior Items Check points Doors • Do the doors operate smoothly? Engine hood • Does the engine hood lock system work properly? Fluid leaks • There should not be any signs of fluid leakage after the vehicle has been parked. Tires • Is the tire inflation pressure correct? • The tires should not be damaged or excessively worn. • Have the tires been rotated according to the maintenance schedule? • The wheel nuts should not be loose.
4-2. Maintenance Emission inspection and maintenance (I/M) programs Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system monitors the operation of the emission control system. ■ If the malfunction indicator lamp comes on The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/M test and may need to be repaired. Contact your Toyota dealer to service the vehicle.
4-3. Do-it-yourself maintenance Do-it-yourself service precautions If you perform maintenance by yourself, be sure to follow the correct procedure as given in these sections. Items Battery condition Brake fluid level Engine coolant level Engine oil level Parts and tools (→P. 532) • Warm water • Baking soda • Grease • Conventional wrench (for terminal clamp bolts) (→P. 528) • FMVSS No.116 DOT 3 or SAE J1703 brake fluid • Rag or paper towel • Funnel (used only for adding brake fluid) (→P.
4-3. Do-it-yourself maintenance Items Parts and tools Fuses Light bulbs (→P. 555) • Fuse with same amperage rating as original (→P. 565) • Bulb with same number and wattage rating as original • Phillips-head screwdriver • Flathead screwdriver • Wrench Power steering fluid level (→P. 530) Radiator and condenser (→P.
4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions: ■ When working on the engine compartment: ● Keep hands, clothing and tools away from the moving fan and engine drive belt. ● Be careful not to touch the engine, radiator, exhaust manifold, etc. right after driving as they may be hot. Oil and other fluids may also be hot.
4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. STEP 1 The hood will pop up slightly. CTH43AS009 Push the auxiliary catch lever to the left and lift the hood. STEP 2 4 CTH43AS142 ■ Pre-driving check Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.
4-3. Do-it-yourself maintenance Engine compartment CTH43AS117 Washer fluid tank (→P. 535) Power steering fluid reservoir (→P. 530) Brake fluid reservoir (→P. 528) Fuse box (→P. 555) Engine oil level dipstick (→P. 522) Battery (→P. 532) Condenser (→P. 527) Engine coolant reservoir (→P. 526) Radiator (→P. 527) Engine oil filler cap (→P.
4-3. Do-it-yourself maintenance Engine compartment cover ■ Removing the engine compartment cover CTH43AS121 ■ Installing the clips 4 Maintenance and care CTH43AS018 NOTICE ■ After installing an engine compartment cover Make sure that the cover is securely installed in its original position.
4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil STEP 1 Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine. STEP 2 Holding a rag under the end, pull the dipstick out. CTH43AS012 STEP 3 Wipe the dipstick clean. STEP 4 Reinsert the dipstick fully.
4-3. Do-it-yourself maintenance ■ Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as that already in the engine. CTH43AS122 Make sure to check the oil type and prepare the items needed before adding oil. Engine oil selection Oil quantity (Low → Full) Items →P. 637 1.8 qt. (1.7 L, 1.5 Imp. qt.) Clean funnel Remove the oil filler cap by turning it counterclockwise. STEP 2 Add engine oil slowly, checking the dipstick.
4-3. Do-it-yourself maintenance ■ Engine oil consumption ● The amount of engine oil consumed depends on the oil viscosity, the quality of the oil and the way the vehicle is driven. ● More oil is consumed under driving conditions such as high speeds and frequent acceleration and deceleration. ● A new engine consumes more oil. ● When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately. ● Oil consumption: Max. 1.1 qt.
4-3. Do-it-yourself maintenance NOTICE ■ To prevent serious engine damage Check the oil level on a regular basis. ■ When replacing the engine oil ● Be careful not to spill engine oil on the vehicle components. ● Avoid overfilling, or the engine could be damaged. ● Check the oil level on the dipstick every time you refill the vehicle. ● Be sure the engine oil filler cap is properly tightened.
4-3. Do-it-yourself maintenance Engine coolant The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir when the engine is cold. Reservoir cap “F” line “L” line If the level is on or below the “L” line, add coolant up to the “F” line. (→P. 627) CTH43AS108 ■ Coolant selection Only use “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology. U.
4-3. Do-it-yourself maintenance CAUTION ■ When the engine is hot Do not remove the engine coolant reservoir cap. The cooling system may be under pressure and may spray hot coolant if the cap is removed, causing serious injuries, such as burns. NOTICE ■ When adding coolant Coolant is neither plain water nor straight antifreeze. The correct mixture of water and antifreeze must be used to provide proper lubrication, corrosion protection and cooling. Be sure to read the antifreeze or coolant label.
4-3. Do-it-yourself maintenance Brake fluid ■ Checking fluid level The brake fluid level should be between the “MAX” and “MIN” lines on the tank. “MAX” line “MIN” line CTH43AS120 ■ Adding fluid Make sure to check the fluid type and prepare the necessary item. Fluid type Item FMVSS No.116 DOT 3 or SAE J1703 brake fluid Clean funnel ■ Refilling brake fluid STEP 1 Vehicles without a smart key system Turn the engine switch off. Vehicles with a smart key system Turn the “ENGINE START STOP” switch off.
4-3. Do-it-yourself maintenance ■ Brake fluid can absorb moisture from the air Excess moisture in the brake fluid can cause a dangerous loss of braking efficiency. Use only newly opened brake fluid. CAUTION ■ When filling the reservoir Take care as brake fluid can harm your hands and eyes and damage painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately. If you still experience discomfort, see a doctor.
4-3. Do-it-yourself maintenance Power steering fluid ■ Fluid level The fluid level should be within the appropriate range. Full (when cold) Add fluid (when cold) Full (when hot) Add fluid (when hot) CTH43AS016 Hot: Vehicle has been driven around 50 mph (80 km/h) for 20 minutes, or slightly longer in frigid temperatures. (Fluid temperature, 140°F - 175°F [60°C - 80°C]). Cold: Engine has not been run for about 5 hours. (Room temperature, 50°F - 85°F [10°C - 30°C]).
4-3. Do-it-yourself maintenance ■ Checking the fluid level Make sure to check the fluid type and prepare the necessary items. Fluid type Items Automatic transmission fluid DEXRON® II or III Rag or paper, clean funnel (only for adding fluid) STEP 1 Clean all dirt off the reservoir. STEP 2 Remove the cap by turning it counterclockwise. STEP 3 Wipe the dipstick clean. STEP 4 Reinstall the cap and remove it again. STEP 5 Check the fluid level.
4-3. Do-it-yourself maintenance Battery Check the battery as follows: Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps. Terminals Hold-down clamp CTH43AS118 ■ Before recharging When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, observe the following before recharging: ● If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.
4-3. Do-it-yourself maintenance ■ After recharging/reconnecting the battery (vehicles with smart key system) ● Unlocking the doors using the smart key system may not be possible immediately after reconnecting the battery. If this happens, use the wireless remote control or the mechanical key to lock/unlock the doors. ● Start the engine with the “ENGINE START STOP” switch in ACCESSORY mode. The engine may not start with the “ENGINE START STOP” switch turned OFF.
4-3. Do-it-yourself maintenance CAUTION ■ Where to safely charge the battery Always charge the battery in an open area. Do not charge the battery in a garage or closed room where there is insufficient ventilation. ■ How to recharge the battery Only perform a slow charge (5 A or less). The battery may explode if charged at a quicker rate. ■ Emergency measures regarding electrolyte ● If electrolyte gets in your eyes Flush your eyes with clean water for at least 15 minutes and get immediate medical attention.
4-3. Do-it-yourself maintenance Washer fluid Type A If any washer does not work or the low washer fluid warning light comes on, the washer tank may be empty. Add washer fluid. CTH43AS119 Type B If the washer fluid level is at “LOW”, add washer fluid. 4 ■ Using the gauge (Type B only) Current fluid level The washer fluid level can be checked by observing the position of the level on the liquid-covered holes in the gauge.
4-3. Do-it-yourself maintenance CAUTION ■ When adding washer fluid Do not add washer fluid when the engine is hot or running as washer fluid contains alcohol and may catch fire if spilled on the engine etc. NOTICE ■ Do not use any fluid other than washer fluid Do not use soapy water or engine antifreeze instead of washer fluid. Doing so may cause streaking on the vehicle’s painted surfaces. ■ Diluting washer fluid Dilute washer fluid with water as necessary.
4-3. Do-it-yourself maintenance Tires Replace or rotate tires in accordance with maintenance schedules and treadwear. ■ Checking tires New tread Treadwear indicator Worn tread The location of treadwear indicators is shown by the “TWI” or “∆” marks, etc., molded on the sidewall of each tire. Check spare tire condition and pressure if not rotated. ■ Tire rotation Rotate the tires in the order shown.
4-3. Do-it-yourself maintenance Installing tire pressure warning valves and transmitters When replacing tires or wheels, tire pressure warning valves and transmitters must also be installed. When new tire pressure warning valves and transmitters are installed, new tire pressure warning valve and transmitter ID codes must be registered in the tire pressure warning computer and the tire pressure warning system must be initialized.
4-3. Do-it-yourself maintenance ■ When to replace your vehicle’s tires Tires should be replaced if: ● You have tire damage such as cuts, splits, cracks deep enough to expose the fabric, and bulges indicating internal damage ● A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer.
4-3. Do-it-yourself maintenance ■ Tire types ● Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads. For driving on snow-covered roads or icy roads, the use of snow tires is recommended. When installing snow tires, be sure to replace all four tires.
4-3. Do-it-yourself maintenance ■ Tire pressure warning system certification FCC ID: PAXPMV107J FCC ID: HYQ13BCX For vehicles sold in the U.S.A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
4-3. Do-it-yourself maintenance NOTICE ■ Repairing or replacing tires, wheels, tire pressure warning valves, transmitters and tire valve caps ● When removing or fitting the wheels, tires or the tire pressure warning valves and transmitters, contact your Toyota dealer as the tire pressure warning valves and transmitter may be damaged if not handled correctly. ● When replacing tire valve caps, do not use tire valve caps other than those specified. The cap may become stuck.
4-3. Do-it-yourself maintenance Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size are displayed on the tire and loading information label. (→P.
4-3. Do-it-yourself maintenance ■ Inspection and adjustment procedure Tire valve Tire pressure gauge STEP 1 Remove the tire valve cap. STEP 2 Press the tip of the tire pressure gauge onto the tire valve. STEP 3 Read the pressure using the gauge gradations. STEP 4 If the tire inflation pressure is not at the recommended level, adjust the pressure. If you add too much air, press the center of the valve to deflate.
4-3. Do-it-yourself maintenance ■ Effects of incorrect tire inflation pressure Driving with incorrect tire inflation pressure may result in the following: ● Reduced fuel efficiency ● Reduced driving comfort and tire life ● Reduced safety ● Damage to the drive train If a tire needs frequent inflating, have it checked by your Toyota dealer. ■ Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: ● Check only when the tires are cold.
4-3. Do-it-yourself maintenance CAUTION ■ Proper inflation is critical to save tire performance Keep your tires properly inflated.
4-3. Do-it-yourself maintenance Wheels If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause a loss of handling control. ■ Wheel selection When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width and inset*. Replacement wheels are available at your Toyota dealer. *: Conventionally referred to as “offset”.
4-3. Do-it-yourself maintenance ■ When replacing wheels The wheels of your vehicle are equipped with tire pressure warning valves and transmitters that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, the tire pressure warning valves and transmitters must be installed. (→P.
4-3. Do-it-yourself maintenance NOTICE ■ Replacing tire pressure warning valves and transmitters ● Because tire repair or replacement may affect the tire pressure warning valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer. ● Ensure that only genuine Toyota wheels are used on your vehicle.
4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be cleaned or changed regularly to maintain air conditioning efficiency. ■ Removal method STEP 1 Turn the engine switch (vehicles without a smart key system) or “ENGINE START STOP” switch (vehicles with a smart key system) off. STEP 2 Open the glove box and remove the cover. CTH43AS089 Remove the filter cover. STEP 3 CTH43AS024 Remove the filter.
4-3. Do-it-yourself maintenance ■ Cleaning method If the filter is dirty, clean by blowing compressed air through the filter from the underside. CTH43AS026 Hold the air gun 2 in. (5 cm) from the filter and blow for approximately 2 minutes at 72 psi (500 kPa, 5.0 kgf/cm2 or bar). If an air gun is not available, have the filter cleaned by your Toyota dealer. 4 ■ Checking interval ■ If air flow from the vents decreases dramatically The filter may be clogged. Check the filter and replace if necessary.
4-3. Do-it-yourself maintenance Wireless remote control/electronic key battery Replace the battery with a new one if it is depleted. ■ You will need the following items: ● Flathead screwdriver ● Lithium battery CR2016 (vehicles without a smart key system), or CR1632 (vehicles with a smart key system) ■ Replacing the battery (vehicles without a smart key system) Remove the cover. STEP 1 To prevent damage to the key, cover the tip of the screwdriver with a rag. STEP 2 Remove the module.
4-3. Do-it-yourself maintenance ■ Replacing the battery (vehicles with a smart key system) STEP 1 Take out the mechanical key. STEP 2 Remove the cover. To prevent damage to the key, cover the tip of the screwdriver with a rag. 4 Insert a new battery with the “+” terminal facing up. 553 4RUNNER_U I nf or mat i onPr ovi dedby: Maintenance and care Remove the depleted battery.
4-3. Do-it-yourself maintenance ■ Use a CR2016 (vehicles without a smart key system) or CR1632 (vehicles with a smart key system) lithium battery ● Batteries can be purchased at your Toyota dealer, local electrical appliance shops or camera stores. ● Replace only with the same or equivalent type recommended by the manufacturer. ● Dispose of used batteries according to local laws.
4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. STEP 1 Vehicles without a smart key system Turn the engine switch off. Vehicles with a smart key system Turn the “ENGINE START STOP” switch off. STEP 2 Open the fuse box cover. Engine compartment Push the tab in and lift the lid off.
4-3. Do-it-yourself maintenance STEP 3 After a system failure, see “Fuse layout and amperage ratings” (→P. 559) for details about which fuse to check. STEP 4 Remove the fuse. Only type A fuse can be removed using the pull-out tool. CTH43AS029 STEP 5 Check if the fuse is blown. Type A Normal fuse Blown fuse Replace the blown fuse with a new fuse of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.
4-3. Do-it-yourself maintenance Type C Normal fuse Blown fuse Replace the blown fuse with a new fuse of an appropriate amperage rating. The amperage rating can be found on the fuse box lid. CTH43AS073 Type D Normal fuse Blown fuse Replace the blown fuse with a new fuse of an appropriate amperage rating. The amperage rating can be found on the fuse box lid. Type E Normal fuse Blown fuse Replace the blown fuse with a new fuse of an appropriate amperage rating.
4-3. Do-it-yourself maintenance Type F Normal fuse Blown fuse Contact your Toyota dealer.
4-3. Do-it-yourself maintenance Fuse layout and amperage ratings ■ Engine compartment CTH43AS139 1 Fuse PTC HTR NO.3 Ampere 30 A Circuit 2 DEF 30 A Rear window defogger 3 DEICER 20 A Windshield wiper de-icer 4 PTC HTR NO.2 30 A PTC heater 5 SUB BATT 30 A Trailer sub battery 6 PTC HTR NO.
4-3. Do-it-yourself maintenance Fuse Ampere 15 H-LP RH-HI 10 A 16 H-LP LH-HI 10 A 17 HTR 50 A Circuit Right-hand headlight (high beam) Left-hand headlight (high beam) Air conditioning system 18 400W INV 80 A Power outlets 19 ST 30 A Starter system 20 H-LP HI 20 A H-LP RH-HI, H-LP LH-HI fuses 21 ALT-S 7.5 A 22 TURN&HAZ 15 A 23 ETCS 10 A 24 PRB 30 A 25 26 27 TOWING SHORT PIN RAD NO.
4-3. Do-it-yourself maintenance Fuse Ampere Circuit 140 A* HTR, 400W INV, A/C COMP, TOWING TAIL, SUB BATT, MIR HTR, DEF, DEICER, STOP, PTC HTR NO.1, PTC HTR NO.2, PTC HTR NO.3, S/HTR FR, ACC, P/OUTLET, IG1, ECU-IG NO.1, ECU-IG NO.2, WIP, WASHER, KDSS, 4WD, BKUP LP, TOWING BKUP, DOOR P, DOOR RL, DOOR RR, DOOR D, P/SEAT FL, P/SEAT FR, DOOR, A/C, OBD, DOOR BACK, S/ROOF, PANEL, TAIL, FOG FR, D/L NO.
4-3. Do-it-yourself maintenance ■ Driver’s side instrument panel 1 2 3 Fuse TAIL PANEL GAUGE Ampere 10 A 7.5 A 7.5 A 4 IGN 10 A 5 6 7 8 9 WASHER WIP S/ROOF DOOR RR DOOR D 20 A 30 A 25 A 25 A 25 A 10 DOOR BACK 30 A 11 12 13 DOOR P P/SEAT FR S/HTR FR 30 A 30 A 20 A 14 ECU-IG NO.2 10 A 15 IG1 7.5 A 16 ECU-IG NO.1 10 A 17 DOOR 7.
4-3. Do-it-yourself maintenance 18 19 20 21 22 Fuse DOOR RL AM1 A/C OBD FOG FR Ampere 25 A 7.5 A 7.5 A 7.5 A 15 A 23 D/L NO.2 25 A 24 25 P/SEAT FL 4WD 30 A 20 A 26 KDSS 10 A 27 28 TOWING BKUP BKUP LP 10 A 10 A 29 ACC 7.
4-3. Do-it-yourself maintenance ■ After a fuse is replaced ● If the lights do not turn on even after the fuse has been replaced, a bulb may need replacement. (→P. 565) ● If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer. ■ If there is an overload in a circuit The fuses are designed to blow, protecting the wiring harness from damage. CAUTION ■ To prevent system breakdowns and vehicle fire Observe the following precautions.
4-3. Do-it-yourself maintenance Light bulbs You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer. ■ Preparing for light bulb replacement Check the wattage of the light bulb to be replaced. (→P. 644) ■ Removing the engine compartment cover →P.
4-3. Do-it-yourself maintenance ■ Rear bulb locations Stop/tail and rear side marker light Back-up light Rear turn signal light License plate lights CTH43AS102 Replacing light bulbs ■ Headlight Turn the bulb base counterclockwise.
4-3. Do-it-yourself maintenance Unplug the connector while depressing the lock release. STEP 2 High beam Low beam CTH43AS091 ■ Parking light and front side marker light Turn the steering wheel in the opposite direction of the parking light and front side marker light that you wish to replace. STEP 1 CTH43AS072 For example, if you wish to replace the parking light and front side marker light on the right side, turn the steering wheel to the left. CTH43AS092 Partly remove the fender liner.
4-3. Do-it-yourself maintenance Turn the bulb base counterclockwise. STEP 4 CTH43AS114 Remove the light bulb. STEP 5 CTH43AS115 ■ Fog light Turn the steering wheel in the opposite direction of the fog light that you wish to replace. STEP 1 For example, if you wish to replace the fog light on the right side, turn the steering wheel to the left. CTH43AS072 Remove the fender liner screws.
4-3. Do-it-yourself maintenance Partly remove the fender liner. STEP 3 CTH43AS093 Unplug the connector while depressing the lock release. STEP 4 CTH43AS094 4 CTH43AS095 569 4RUNNER_U I nf or mat i onPr ovi dedby: Maintenance and care Turn the bulb base counterclockwise.
4-3. Do-it-yourself maintenance ■ Front turn signal light and daytime running light Turn the steering wheel in the opposite direction of the front turn signal light and daytime running light that you wish to replace. STEP 1 CTH43AS072 For example, if you wish to replace the front turn signal light and daytime running light on the right side, turn the steering wheel to the left. Remove the fender liner screws. STEP 2 CTH43AS092 Partly remove the fender liner.
4-3. Do-it-yourself maintenance Turn the bulb base counterclockwise. STEP 4 CTH43AS060 Remove the light bulb.
4-3. Do-it-yourself maintenance ■ Stop/tail and rear side marker light and back-up light Open the back door and remove the cover. STEP 1 Using a flathead screwdriver or equivalent which is wrapped with a cloth. CTH43AS042 Turn the bulb base counterclockwise. STEP 2 Stop/tail and rear side marker light Back-up light CTH43AS043 Remove the light bulb.
4-3. Do-it-yourself maintenance ■ Rear turn signal light Open the back door and remove the cover. STEP 1 Using a flathead screwdriver or equivalent which is wrapped with a cloth. 4 CTH43AS042 CTH43AS045 Remove the light bulb. STEP 3 CTH43AS046 573 4RUNNER_U I nf or mat i onPr ovi dedby: Maintenance and care Turn the bulb base counterclockwise.
4-3. Do-it-yourself maintenance ■ License plate light Remove the screws and lens. STEP 1 CTH43AS103 Remove the light bulb. STEP 2 CTH43AS048 ■ Lights other than the above If any of the lights listed below has burnt out, have your Toyota dealer replace it.
4-3. Do-it-yourself maintenance ■ LED light bulbs The side turn signal lights and high mounted stoplight consist of a number of LEDs. If any LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. ■ Condensation build-up on the inside of the lens Contact your Toyota dealer for more information in the following situations. Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction.
4-3.
5-1. Essential information Emergency flashers Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash all the turn signal lights. To turn them off, press the switch once again. CTH51AS005 NOTICE ■ To prevent battery discharge Do not leave the emergency flashers on longer than necessary when the engine is not running.
5-1. Essential information If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or flatbed truck. Use a safety chain system for all towing, and abide by all state/provincial and local laws. Before towing The following may indicate a problem with your transmission. Contact your Toyota dealer before towing. ● The engine is running but the vehicle will not move.
5-1. Essential information Vehicles with a front spoiler only: Before using the front emergency towing eyelet(s), remove the cover(s). CTH51AS007 Removing the clips Installing the clips CTH51AS008 Towing with a sling-type truck Do not tow with a sling-type truck to prevent body damage.
5-1. Essential information Towing with a wheel lift-type truck From the front Use a towing dolly under the rear wheels. From the rear (2WD models) Vehicles without a smart key system: Turn the engine switch to the “ACC” position so that the steering wheel is unlocked. Vehicles with a smart key system: Turn the “ENGINE START STOP” switch to ACCESSORY mode so that the steering wheel is unlocked. Full-time 4WD models: Use a towing dolly under the front wheels.
5-1. Essential information Using a flatbed truck If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°. Do not overly tighten the tie downs or the vehicle may be damaged. CTH51AS011 ■ Before emergency towing STEP 1 Vehicles without a smart key system: Turn the engine switch to the “ACC” (engine off) or “ON” position. Vehicles with a smart key system: Turn the “ENGINE START STOP” switch to ACCESSORY (engine off) or IGNITION ON mode (engine running).
5-1. Essential information CAUTION ■ Caution while towing ● Use extreme caution when towing the vehicle. Avoid sudden starts or erratic driving maneuvers which place excessive stress on the emergency towing eyelets and the cables or chains. Always be cautious of the surroundings and other vehicles while towing. ● Vehicles with a smart key system: Do not turn the “ENGINE START STOP” switch off.
5-1. Essential information NOTICE ■ To prevent body damage when towing with a sling-type truck Do not tow with a sling-type truck, either from the front or rear. ■ To prevent causing serious damage to the transmission and transfer (4WD models) in emergency towing Never tow a vehicle from the rear with four wheels on the ground. This may cause serious damage to the transmission and transfer.
5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms ● Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.
5-1. Essential information Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or when an airbag inflates upon collision, the fuel pump shut off system stops the supply of fuel to the engine. Follow the procedure below to restart the engine after the system is activated. Vehicles without a smart key system STEP 1 Turn the engine switch to the “ACC” or “LOCK” position. STEP 2 Restart the engine.
5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds Calmly perform the following actions if any of the warning lights comes on or flashes. If a light comes on or flashes, but then goes off, this does not necessarily indicate a malfunction in the system. However, if this continues to occur, have the vehicle inspected by your Toyota dealer. Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous.
5-2. Steps to take in an emergency Stop the vehicle immediately. The following warnings indicate the possibility of damage to the vehicle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer.
5-2. Steps to take in an emergency Warning light (U.S.A.
5-2. Steps to take in an emergency Warning light Warning light/Details Power steering warning light Indicates a malfunction in the power steering system Unengaged “Park” warning light (if equipped) Indicates a malfunction in the transmission “Park” mechanism.
5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning light goes off. Warning light Correction procedure Open door warning light (warning buzzer)*1 Indicates that a door is not fully closed Check that all the doors are closed. Low fuel level warning light Indicates remaining fuel is approximately 3.5 gal. (13.1 L, 2.9 Imp. gal.) or less Refuel the vehicle.
5-2. Steps to take in an emergency Warning light Warning light/Details Correction procedure Tire pressure warning light (Comes on) (Canada) When the light comes on: Low tire inflation pressure such as • Natural causes (→P. 598) • Flat tire (→P. 603) Adjust the tire inflation pressure (including the spare tire) to the specified level. The light will turn off after a few minutes.
5-2. Steps to take in an emergency Warning light Warning light/Details Correction procedure Maintenance required reminder light Indicates that maintenance is required according to the driven distance on the maintenance schedule.*3 (U.S.A.) Illuminates for about 3 seconds and then flashes for about 15 seconds approximately 4500 miles (7200 km) after the maintenance data has been reset. If necessary, perform maintenance.
5-2. Steps to take in an emergency *1:Open door warning buzzer: The open door warning buzzer sounds to alert one or more of the doors is not fully closed (with the vehicle having reached a speed of 3 mph [5 km/h]). *2:Driver’s and front passenger’s seat belt buzzer: The driver’s and front passenger’s seat belt buzzer sounds to alert the driver and front passenger that his or her seat belt is not fastened.
5-2. Steps to take in an emergency Follow the correction procedures. (vehicles with a smart key system) After taking the specified steps to correct the suspected problem, check that the warning light goes off. Interior buzzer Once Once Warning light Warning light/Details Correction procedure ⎯ Smart key system warning light Indicates that the electronic key is not present when the “ENGINE START STOP” switch is pressed Confirm the location of the electronic key*.
5-2. Steps to take in an emergency Interior buzzer Continuous Once Warning light/Details Correction procedure Continuous Smart key system warning light Indicates that the driver’s door has been opened and closed with the shift lever not in P, the “ENGINE START STOP” switch in any mode other than off and the electronic key has been taken out of the detection area • Shift the shift lever to P. • Confirm the location of the electronic key.
5-2.
5-2. Steps to take in an emergency ■ The tire pressure warning light may come on due to natural causes The tire pressure warning light may come on due to natural causes such as natural air leaks and tire inflation pressure changes caused by temperature. In this case, adjusting the tire inflation pressure will turn off the warning light (after a few minutes). ■ When a tire is replaced with a spare tire The spare tire is not equipped with a tire pressure warning valve and transmitter.
5-2. Steps to take in an emergency ■ If the tire pressure warning system is not functioning The tire pressure warning system will be disabled in the following conditions: (When the condition becomes normal, the system will work properly.) ● If tires not equipped with tire pressure warning valves and transmit- ters are used ● If the ID code on the tire pressure warning valves and transmitters is not registered in the tire pressure warning computer ● If the tire inflation pressure is 73 psi (500 kPa, 5.
5-2. Steps to take in an emergency CAUTION ■ If the tire pressure warning light comes on Be sure to observe the following precautions. Failure to do so could cause a loss of vehicle control and result in death or serious injury. ● Stop your vehicle in a safe place as soon as possible. Adjust the tire inflation pressure immediately. ● If the tire pressure warning light comes on even after tire inflation pres- sure adjustment, it is probable that you have a flat tire. Check the tires.
5-2. Steps to take in an emergency CAUTION ■ Maintenance of the tires Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label).
5-2. Steps to take in an emergency CAUTION Your vehicle has also been equipped with a TPMS (tire pressure warning system) malfunction indicator to indicate when the system is not operating properly. The TPMS (tire pressure warning system) malfunction indicator is combined with the low tire pressure telltale (tire pressure warning light). When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated.
5-2. Steps to take in an emergency If you have a flat tire Remove the flat tire and replace it with the spare tire provided. ■ Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ● Shift the shift lever to P. ● Stop the engine. ● Turn on the emergency flashers.
5-2. Steps to take in an emergency Taking out the jack and tool bag Remove the cover. STEP 1 CTH52AS020 Unhook and take out the tool bag. STEP 2 CTH52AS004 Take out the jack.
5-2. Steps to take in an emergency Taking out the spare tire STEP 1 Assembling the jack handle. Remove the jack handle and the jack handle extension bar from the tool bag and assembly by following these steps. Loosen the bolt and the screw using either the jack handle or a screwdriver. CTH52AS051 Assemble the jack handle extension bars and tighten the bolt. Check that the bolt is firmly tightened. 5 CTH52AS052 Check that the screw is firmly tightened.
5-2. Steps to take in an emergency Insert the end of the jack handle extension into the lowering screw and turn it counterclockwise. STEP 2 Lower the spare tire completely to the ground. CTH52AS008 Pull out the spare tire and remove the holding bracket.
5-2. Steps to take in an emergency Replacing a flat tire Chock the tires. STEP 1 Flat tire CTH52AS038 Wheel chock positions Lefthand side Behind the rear righthand side tire Righthand side Behind the rear lefthand side tire Lefthand side In front of the front right-hand side tire Righthand side In front of the front left-hand side tire Front Rear 5 CTH52AS041 To protect the wheel place a rag between ornament remover wheel ornament, as the illustration.
5-2. Steps to take in an emergency Slightly loosen the wheel nuts (one turn). STEP 3 CTH52AS012 STEP 4 Assembling the jack handle. Remove the jack handle, jack handle extension bar and jack handle bar from the tool bag and assembly by following these steps. Loosen the bolts and the screw using either the jack handle or a screwdriver. CTH52AS054 Assemble the jack handle extension bars and the jack handle bar and tighten the bolts. Check that the bolts are firmly tightened.
5-2. Steps to take in an emergency Assemble the jack handle extension bar and the jack handle and tighten the screw. Check that the screw is firmly tightened. CTH52AS056 Position the jack at the jack points as shown. STEP 5 Front - Under the chassis frame side rail Rear - Under the rear axle housing 5 Raise the vehicle until the tire is slightly raised off the ground.
5-2. Steps to take in an emergency Remove all the wheel nuts and the tire. STEP 7 When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface. CTH52AS016 Installing the spare tire Remove any dirt or foreign matter from the wheel contact surface. STEP 1 CTH52AS017 STEP 2 If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, causing the tire to come off.
5-2. Steps to take in an emergency Washer When replacing an aluminum wheel with an aluminum wheel, tighten the wheel nuts until the washers comes into contact with the disc wheel. Disc wheel CTH52AS037 Lower the vehicle. STEP 3 CTH52AS019 Firmly tighten each wheel nut two or three times in the order shown in the illustration. STEP 4 Tightening torque: 81 ft•lbf (110 N•m, 11.
5-2. Steps to take in an emergency Stowing the flat/spare tire, jack and tools Lay down the tire with the outer side facing up, and install the holding bracket. STEP 1 Insert the holding bracket tab into one of the holes in the wheel. CTH52AS059 STEP 2 Raise the tire. Vehicles with kinetic dynamic suspension: Pull the tire toward the rear of the vehicle when raising. After raising, visually check that tire is not interfering with components.
5-2. Steps to take in an emergency CAUTION ■ Using the tire jack Improper use of the tire jack may cause the vehicle to suddenly fall off the jack, leading to death or serious injury. ● Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains. ● Only use the tire jack that comes with this vehicle for replacing a flat tire. Do not use it on other vehicles, and do not use other tire jacks for replacing tires on this vehicle.
5-2. Steps to take in an emergency CAUTION ■ Using the jack handle Tighten all the jack handle bolts securely using a Phillips-head screwdriver, to prevent the extension parts from coming apart unexpectedly. ■ Replacing a flat tire ● Observe the following precautions. Failure to do so may result in serious injury: • Lower the spare tire completely to the ground before removing it from under the vehicle. • Do not try to remove the wheel ornament by hand.
5-2. Steps to take in an emergency NOTICE ■ Do not drive the vehicle with a flat tire Do not continue driving with a flat tire. Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair. ■ When stowing the flat tire Ensure that there is no object caught between the tire and the vehicle underbody.
5-2. Steps to take in an emergency If the engine will not start If the engine will not start even though correct starting procedures are being followed (→P. 170, 173), consider each of the following points: ■ The engine will not start even though the starter motor operates normally. One of the following may be the cause of the problem: ● There may not be sufficient fuel in the vehicle’s tank. Refuel the vehicle. ● The engine may be flooded.
5-2. Steps to take in an emergency ■ The starter motor does not turn over, the interior lights and headlights do not turn on, or the horn does not sound. One of the following may be the cause of the problem: ● One or both of the battery terminals may be disconnected. ● The battery may be discharged. (→P. 623) ● There may be a malfunction in the steering lock system. (vehicles with a smart key system) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown.
5-2. Steps to take in an emergency If the shift lever cannot be shifted from P If the shift lever cannot be shifted with your foot on the brake pedal, there may be a problem with the shift lock system (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted: STEP 1 Set the parking brake.
5-2. Steps to take in an emergency If you lose your keys New genuine keys can be made by your Toyota dealer. For vehicles with the smart key system, bring the other key and the key number stamped on the key number plate. For vehicles without the smart key system, bring a master key and the key number stamped on the key number plate.
5-2. Steps to take in an emergency If you cannot operate back door opener If the back door opener does not operate, there may be a problem with the back door opener system. Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the back door can be opened from the inside. Remove the cover on the back door trim. STEP 1 CTH52AS023 Tear the plastic film. Remove the cover. STEP 2 CTH52AS040 Pull the lever.
5-2. Steps to take in an emergency If the electronic key does not operate properly (vehicles with a smart key system) If communication between the electronic key and vehicle is interrupted (→P. 43) or the electronic key cannot be used because the battery is depleted, the smart key system and wireless remote control cannot be used. In such cases, the doors can be opened and the engine can be started by following the procedure below. Locking and unlocking the doors Use the mechanical key (→P.
5-2. Steps to take in an emergency Changing “ENGINE START STOP” switch modes and starting the engine STEP 1 Ensure that the shift lever is in P and depress the brake pedal. STEP 2 Touch the Toyota emblem side of the electronic key to the “ENGINE START STOP” switch. CTH52AS002 STEP 3 If any of the doors is opened or closed while the key is being touched to the switch, an alarm will sound to indicate that the start function cannot detect the key.
5-2. Steps to take in an emergency If the vehicle battery is discharged The following procedures may be used to start the engine if the vehicle's battery is discharged. You can also call your Toyota dealer or a qualified repair shop. If you have a set of jumper (or booster) cables and a second vehicle with a 12-volt battery, you can jump start your vehicle by following the steps below.
5-2. Steps to take in an emergency STEP 2 Start the engine of the second vehicle. Increase the engine speed slightly and maintain at that level for approximately 5 minutes to recharge the battery of your vehicle. STEP 3 Vehicles with a smart key system only: Open and close any of the doors of your vehicle with the “ENGINE START STOP” switch off.
5-2. Steps to take in an emergency ■ Starting the engine when the battery is discharged The engine cannot be started by push-starting. ■ To prevent battery discharge ● Turn off the headlights and the audio system while the engine is off. ● Turn off any unnecessary electrical components when the vehicle is running at a low speed for an extended period, such as in heavy traffic.
5-2. Steps to take in an emergency CAUTION ■ Avoiding battery fires or explosions Observe the following precautions to prevent accidentally igniting the flammable gas that may be emitted from the battery: ● Make sure each jumper cable is connected to the correct terminal and that it is not unintentionally in contact with any other than the intended terminal. ● Do not allow the + and - clamps of the jumper cables to come into contact with each other.
5-2. Steps to take in an emergency If your vehicle overheats If your engine overheats: STEP 1 Stop the vehicle in a safe place and turn off the air conditioning system. STEP 2 Check to see if steam is coming out from under the hood. If you see steam: Stop the engine. Carefully lift the hood after the steam subsides and then restart the engine. If you do not see steam: Leave the engine running and carefully lift the hood. STEP 3 Check to see if the cooling fan is operating.
5-2. Steps to take in an emergency Add engine coolant if necessary. STEP 5 Water can be used in an emergency if engine coolant is unavailable. (→P. 639) CTH52AS033 Have the vehicle inspected at the nearest Toyota dealer as soon as possible. ■ Overheating If you observe the following, your vehicle may be overheating: ● The engine coolant temperature gauge enters the red zone or a loss of power is experienced. ● Steam comes out from under the hood.
5-2. Steps to take in an emergency NOTICE ■ When adding engine coolant Wait until the engine has cooled down before adding engine coolant. When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine.
5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt or snow: STEP 1 Stop the engine. Set the parking brake and shift the shift lever to P. STEP 2 Remove the mud, snow or sand from around the stuck tire. STEP 3 Place wood, stones or some other material under the tires to help provide traction. STEP 4 Restart the engine.
5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following procedure: STEP 1 Steadily step on the brake pedal with both feet and firmly depress it. Do not pump the brake pedal repeatedly as this will increase the effort required to slow the vehicle. STEP 2 Shift the shift lever to N.
5-2. Steps to take in an emergency Vehicles with a smart key system: Stop the engine by pressing and holding the “ENGINE START STOP” switch for 3 consecutive seconds or more. STEP 4 Press and hold for 3 seconds or more STEP 5 Stop the vehicle in a safe place by the road. CAUTION ■ If the engine has to be turned off while driving ● Power assist for the brakes and steering wheel will be lost, making the brake pedal harder to depress and the steering wheel heavier to turn.
6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions and weights Overall length 189.8 in. (4820 mm) Overall width 75.8 in. (1925 mm) Overall height *1 70.1 in. (1780 mm) Wheelbase Tread 109.8 in. (2790 mm) Front 63.2 in. (1605 mm) Rear 63.2 in. (1605 mm) 1165 lb. (525 kg) *2 Vehicle capacity weight (Occupants + luggage) 835 lb. (375 kg) *3 Trailer weight rating (trailer weight + cargo weight) Luggage compartment load capacity *1: *2: *3: *4: *5: 5000 lb. (2270 kg) 970 lb.
6-1. Specifications Vehicle identification ■ Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel. CTH61AS001 This number is also on the Certification Label.
6-1. Specifications Engine Model 1GR-FE Type 6-cylinder V type, 4-cycle, gasoline Bore and stroke 3.70 × 3.74 in. (94.0 × 95.0 mm) Displacement 241.4 cu.in. (3956 cm3) Valve clearance (engine cold) Automatic adjustment Drive belt tension Automatic adjustment Fuel Fuel type Unleaded gasoline only Octane rating 87 (Research octane number 91) or higher Fuel tank capacity (Reference) 23.0 gal. (87.0 L, 19.1 Imp. gal.
6-1. Specifications Lubrication system Oil capacity (Drain and refill ⎯ reference) With filter Without filter 6.6 qt. (6.2 L, 5.5 Imp. qt.) 6.0 qt. (5.7 L, 5.0 Imp. qt.) ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity.
6-1. Specifications How to read oil container label: The ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is added to some oil containers to help you select the oil you should use.
6-1. Specifications Cooling system Capacity 11.1 qt. (10.5 L, 9.2 Imp. qt.) Coolant type Use either of the following: • “Toyota Super Long Life Coolant” • A similar high-quality ethylene glycolbased non-silicate, non-amine, nonnitrite, and non-borate coolant with longlife hybrid organic acid technology Do not use plain water alone. Ignition system Spark plug Make Gap DENSO SK20HR11 0.043 in. (1.1 mm) NOTICE ■ Iridium-tipped spark plugs Use only iridium-tipped spark plugs.
6-1. Specifications Electrical system Battery Open voltage* at 68°F (20°C): 12.6 ⎯ 12.8 V Fully charged 12.2 ⎯ 12.4 V Half charged 11.8 ⎯ 12.0 V Discharged (*: Voltage checked 20 minutes after the engine and all the lights are turned off.) Charging rates 5 A max. Transfer (4WD models) Oil capacity Part-time 4WD models 1.1 qt. (1.0 L, 0.9 Imp. qt.) Full-time 4WD models 1.5 qt. (1.4 L, 1.2 Imp. qt.
6-1. Specifications Front differential (4WD models) Oil capacity Part-time 4WD models 1.6 qt. (1.55 L, 1.4 Imp. qt.) Full-time 4WD models 1.5 qt. (1.40 L, 1.2 Imp. qt.) Oil type and viscosity* Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent *: Your Toyota vehicle is filled with “Toyota Genuine Differential Gear Oil” at the factory. Use Toyota approved “Toyota Genuine Differential Gear Oil” or an equivalent of matching quality to satisfy the above specification.
6-1. Specifications Automatic transmission Fluid capacity* 11.3 qt. (10.7 L, 9.4 Imp. qt.) Fluid type Toyota Genuine ATF WS *: The fluid capacity is a reference quantity. If replacement is necessary, contact your Toyota dealer. NOTICE ■ Transmission fluid type Using transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of the transmission accompanied by vibration and, ultimately, damage to the vehicle’s transmission. Brakes Pedal clearance*1 3.
6-1. Specifications Chassis lubrication Propeller shafts Spider Lithium base chassis grease, NLGI No.2 Slide yoke Molybdenum-disulfide lithium base chassis grease, NLGI No.2 or lithium base chassis grease, NLGI No.2 Steering Free play Less than 1.2 in. (30 mm) Power steering fluid type Automatic transmission fluid DEXRON® II or III Tires and wheels Tire size P265/70R17 113S, P245/60R20 107H Tire inflation pressure (Recommended cold tire inflation pressure) Front: 32 psi (220 kPa, 2.
6-1. Specifications Light bulbs Light Bulbs Bulb No.
6-1. Specifications Fuel information You must only use unleaded gasoline in your vehicle. Select octane rating 87 (Research Octane Number 91) or higher. Use of unleaded gasoline with an octane rating lower than 87 may result in engine knocking. Persistent knocking can lead to engine damage. At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada.
6-1. Specifications ■ Recommendation of the use of gasoline containing detergent additives ● Toyota recommends the use of gasoline that contains detergent additives to avoid the build-up of engine deposits. ● All gasoline sold in the U.S.A. contains detergent additives to clean and/ or keep clean intake systems.
6-1. Specifications ■ Non-recommendation of the use of gasoline containing MMT Some gasoline contains an octane enhancing additive called MMT (Methylcyclopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.
6-1. Specifications Tire information Typical tire symbols CTH61AS021 Tire size (→P. 650) Summer tire or all season tires (→P. 540) An all season tire has “M+S” on the sidewall. A tire not marked “M+S” is a summer tire. Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. DOT and Tire Identification Number (TIN) (→P. 649) Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire.
6-1. Specifications Maximum cold tire inflation pressure (→P. 643) This means the pressure to which a tire may be inflated. TUBELESS or TUBE TYPE A tubeless tire does not have a tube and air is directly put into the tire. A tube type tire has a tube inside the tire and the tube maintains the air pressure. Radial tires or bias-ply tires A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL” is a bias-ply tire.
6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size.
6-1. Specifications Tire section names Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer Uniform Tire Quality Grading This information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading.
6-1. Specifications ■ Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use.
6-1. Specifications Warning: The temperature grades of a tire assume that it is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Glossary of tire terminology Tire related term Meaning Tire pressure when the vehicle has been parked for three hours or more, or has not been driven more than 1 mile or 1.
6-1. Specifications Tire related term Meaning Normal occupant weight 150 lb. (68 kg) times the number of occupants specified in the second column of Table 1* that follows Occupant distribution Distribution of occupants in a vehicle as specified in the third column of Table 1* below Production options weight The combined weight of installed regular production options weighing over 5 lb. (2.
6-1.
6-1.
6-1. Specifications Tire related term Meaning Passenger car tire A tire intended for use on passenger cars, multipurpose passenger vehicles, and trucks, that have a gross vehicle weight rating (GVWR) of 10,000 lb. or less.
6-1.
6-1.
6-2. Customization Customizable features Your vehicle includes a variety of electronic features that can be personalized to suit your preferences. Programming these preferences requires specialized equipment and may be performed by your Toyota dealer. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details. Item Smart key system and wireless remote control (→P.
6-2. Customization Item Door lock (→P. 53, 621) Power windows (→P.
6-2. Customization Item Function Time period before lights turn off Illumination (→P. 438) Default setting 15 seconds Customized setting 7.
6-2. Customization Item Outer foot lights (if equipped) (→P. 438) Default setting Customized setting Vehicles with a smart key system: Operation when you approach the vehicle with the electronic key on your person On Off Operation when the doors are unlocked using the wireless remote control, key or entry function On Off Operation when the doors are unlocked using the door lock switch On Off Time period before lights turn off 15 seconds 7.
6-2. Customization Item Rear window wiper and washer (→P. 214) Power back window (→P.
6-2. Customization Item Power back window (→P. 101) Function Vehicles with a smart key system: Time required to press and hold the switch before the window begins to open/close Intuitive parking assist (→P. 221) Buzzer volume Seat belt reminder (→P. 591) Vehicle speed linked seat belt reminder buzzer Default setting Customized setting 1 second 0.8 seconds 1.2 seconds 1.4 seconds Max. Min. to Max.
6-3. Initialization Items to initialize The following item must be initialized for normal system operation in cases such as after the battery is reconnected, or maintenance is performed on the vehicle. Item Maintenance data When to initialize Reference After the maintenance is performed P.
Reporting safety defects for U.S. owners If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English. Utilisation correcte des ceintures de sécurité ● Déroulez la sangle diagonale de telle sorte qu'elle passe bien sur l'épaule, sans pour autant être en contact avec le cou ou glisser de l'épaule.
Entretien et soin ■ Ceintures de sécurité Nettoyez avec un chiffon ou une éponge humectée d'eau savonneuse tiède. Vérifiez régulièrement que les ceintures ne sont pas effilochées, entaillées ou exagérément usées. ATTENTION ■ Détérioration et usure des ceintures de sécurité Inspectez les ceintures de sécurité périodiquement. Contrôlez qu'elles ne sont pas entaillées, effilochées et que leurs ancrages ne sont pas desserrés. Ne pas utiliser une ceinture de sécurité défectueuse avant qu'elle ne soit remplacée.
SRS airbag instructions for Canadian owners (in French) The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instructions in English.
Airbags SRS latéraux et rideau Airbags SRS latéraux Participent à la protection du haut du corps des occupants assis aux places avant Airbags SRS rideau Participent principalement à la protection de la tête des occupants assis aux places extérieures 672 4RUNNER_U I nf or mat i onPr ovi dedby:
Composition du système de sacs de sécurité gonflables SRS CTH17AS100 Airbags latéraux Témoins indicateurs “AIR BAG ON” et “AIR BAG OFF” Airbags rideau Airbag passager avant Airbags de genoux Capteurs d’airbags latéraux et rideau Capteurs d’airbag avant Boîtier électronique d’airbags Contacteur de boucle de ceinture de sécurité passager avant Système de détection de l'occupant (ECU et capteurs) Capteurs des airbags rideau Témoin d’alerte SRS témoin “RSCA OFF” et Commutateur de désactivation de la foncti
Votre véhicule est équipé de ADVANCED AIRBAGS conçus selon les normes de sécurité américaines applicables aux véhicules à moteur (FMVSS208). Le système d’airbag contrôle la puissance de déploiement des airbags pour le conducteur et le passager avant. Le système d’airbag conducteur comprend le contacteur de boucle de ceinture de sécurité conducteur, etc. Le système d’airbag passager avant comprend le capteur de classification des occupants du siège passager avant, etc.
ATTENTION ■ Précautions avec les airbags SRS Respectez les précautions suivantes concernant les airbags SRS. Autrement, des blessures graves, voire mortelles, pourraient s'ensuivre. ● Le conducteur et tous les passagers à bord du véhicule doivent porter leur ceinture de sécurité correctement. Les airbags SRS sont des dispositifs de protection complémentaires aux ceintures de sécurité.
ATTENTION ■ Précautions avec les airbags SRS CTH17AS014 ●Si vous attachez une rallonge de ceinture de sécurité à la boucle de ceinture de sécurité du siège conducteur, mais pas au pêne de la ceinture de sécurité du siège conducteur, l'airbag SRS du siège conducteur détecte que le conducteur a attaché sa ceinture de sécurité, alors même que ce n'est pas le cas.
ATTENTION ■ Précautions avec les airbags SRS ● N'inclinez pas le dossier du siège passager avant au point qu'il vienne à toucher le siège arrière. Le témoin indicateur “AIR BAG OFF” risquerait alors de s’allumer, indiquant que les airbags passager ne se déploieront pas en cas d’accident grave. Si le dossier vient à toucher le siège arrière, redressez-le. Réglez le dossier de siège passager avant aussi droit que possible lorsque le véhicule est en mouvement.
ATTENTION ■ Précautions avec les airbags SRS ●Interdisez à quiconque de s'agenouiller sur le siège passager en appui contre la porte ou de sortir la tête ou les mains à l'extérieur du véhicule. CTH17AS018 CTH17AS077 ●Ne fixez ni ne posez aucun objet sur la planche de bord, la garniture centrale du moyeu de volant de direction et la partie inférieure du tableau de bord. Au déploiement des airbags SRS conducteur, passager avant et genoux, tout objet risque de se transformer en projectile.
ATTENTION ■ Précautions avec les airbags SRS ● Ne suspendez aux crochets à vêtements aucun cintre nu ni aucun objet dur. En cas de déploiement des airbags rideau SRS, tous ces objets pourraient se transformer en projectiles et causer des blessures graves, voire mortelles. ● Si un cache en vinyle recouvre la partie où l’airbag SRS de genoux se déploie, veillez à l'enlever.
ATTENTION ■ Modification et mise au rebut des éléments du système d’airbags SRS Consultez impérativement votre concessionnaire Toyota si vous avez besoin d'intervenir sur votre véhicule ou de procéder à l'une des modifications suivantes. Les airbags SRS risquent de ne pas fonctionner correctement ou de se déployer (gonfler) accidentellement, provoquant ainsi des blessures graves, voire mortelles.
Désactivation des airbags rideau en cas de retournement du véhicule Activation/désactivation (maintenez pendant quelques secondes) CTH17AS084 Véhicules dépourvus de système d'accès et de démarrage “mains libres”: Le témoin “RSCA OFF” s'allume. (Uniquement lorsque le contacteur de démarrage antivol est sur la position “ON”).
ATTENTION ■ En marche normale Assurez-vous que le témoin “RSCA OFF” n’est pas allumé. Si vous le laissez en position marche, les airbags rideau ne se déploieront pas en cas d'accident, ce qui peut provoquer des blessures graves, voire mortelles.
Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING 2WD 2 Wheel Drive 4WD 4 Wheel Drive A/C Air Conditioning ABS Anti-lock Brake System ACC Accessory AI-SHIFT Artificial Intelligence Shift control ALR Automatic Locking Retractor A-TRAC Active traction control system AUTO LSD Automatic Limited Slip Differential AUX Auxiliary CRS Child Restraint System DAC Downhill assist control system ECU Electronic Control Unit EDR Event Data Recorder ELR Emergency Locking Retr
Abbreviation list ABBREVIATIONS MEANING M+S Mud and Snow MTBE Methyl Tertiary Butyl Ether OBD On Board Diagnostics RSCA Roll sensing of curtain shield airbag SRS Supplemental Restraint System TIN Tire Identification Number TPMS Tire Pressure Warning System TRAC Traction Control TWR Trailer Weight Rating VIN Vehicle Identification Number VSC Vehicle Stability Control 685 4RUNNER_U I nf or mat i onPr ovi dedby:
Alphabetical index Alphabetical index A A/C.....................................314, 320 ABS ...........................................266 Accessory meter ......................199 Active head restraints ...............69 Active traction control.............243 Air conditioning filter...............550 Air conditioning system Air conditioning filter..............550 Automatic air conditioning system ................................320 Manual air conditioning system ................................
Alphabetical index B Back door C Care Back door ............................... 63 Back window ........................ 101 Smart key system................... 35 Wireless remote control.......... 49 Back-up lights Replacing light bulbs ............ 566 Wattage ................................ 644 Back window ........................... 101 Battery Checking .............................. 532 If the vehicle has a discharged battery ............ 623 Preparing and checking before winter ....................
Alphabetical index Child safety Airbag precautions ................128 Battery precautions .......534, 626 Child-protectors.......................55 Child restraint system............142 How your child should wear the seat belt ..........................89 Installing child restraints........146 Moon roof precautions ..........108 Power window lock switch.......98 Power window precautions ...100 Removed key battery precautions .........................554 Seat belt extender precautions .....................
Alphabetical index E Electronic key If your electronic key battery is depleted...... 552, 621 Emergency flashers Switch................................... 578 Emergency, in case of If the electronic key does not operate properly........... 621 If the engine will not start...... 616 If the shift lever cannot be shifted from P..................... 618 If the vehicle has a discharged battery ............ 623 If the warning buzzer sounds ............................... 587 If the warning light turns on .......
Alphabetical index Fuel Capacity ................................636 Fuel gauge ............................186 Fuel pump shut off system ....586 Gas station information .........700 Information ............................645 Refueling ...............................109 Type ......................................636 Fuel door...................................109 Fuel filler door ..........................109 Fuel pump shut off system ....................................586 Fuses..........................
Alphabetical index L Language M Maintenance Audio .................................... 334 Licence plate lights Replacing light bulbs ............ 565 Wattage ................................ 644 Light bulbs Replacing ............................. 565 Wattage ................................ 644 Lights Door courtesy lights.............. 438 Emergency flasher switch .... 578 Engine switch light................ 438 Fog light switch..................... 209 Footwell lights.......................
Alphabetical index O Odometer ..................................186 R Radiator .................................... 527 Off-road precautions ...............275 Oil Engine oil ..............................522 Opener Fuel filler door .......................109 Hood......................................519 Outside rear view mirrors Adjusting and folding...............96 Outside temperature display ....................................457 Overhead console....................447 Overheating, Engine ..........
Alphabetical index S Safety Connect ........................ 493 Seat belts Adjusting the seat belt ............ 86 Automatic Locking Retractor .............................. 88 Child restraint system installation .......................... 146 Cleaning and maintaining the seat belts...................... 506 Emergency Locking Retractor .............................. 88 How to wear your seat belt..... 86 How your child should wear the seat belt .........................
Alphabetical index Storage compartment..............482 Storage feature.........................441 Storage precautions ................284 Stuck If your vehicle becomes stuck ...................................630 Sun visors.................................453 Sunshade Roof.......................................105 Switch Emergency flasher switch .....578 Engine switch ................170, 173 Fog light switch .....................209 Hazard light switch ................578 Ignition switch................
Alphabetical index Turn signal lights Replacing light bulbs ............ 565 Switch................................... 183 Wattage ................................ 644 V Valet key..................................... 32 Vanity lights Vanity lights .......................... 454 Wattage ................................ 644 Vanity mirrors.......................... 454 Vehicle identification number................................... 635 Vehicle stability control.......... 266 VSC.............................
What to do if... What to do if... A tire punctures P. 603 If you have a flat tire P. 113 Engine immobilizer system The engine does not start P. 616 If the engine will not start P. 623 If the vehicle battery is discharged The shift lever cannot be moved out of P P. 618 If the shift lever cannot be shifted from P The engine coolant temperature gauge enters the red zone P. 627 If your vehicle overheats Steam can be seen coming from under the hood The key is lost P.
What to do if...
What to do if... ■Warning lights Brake system warning light Unengaged “Park” warning light P. 588 or P. 587 Power steering warning light P. 588 Charging system warnP. 588 ing light Low fuel level warning P. 591 light Low engine oil pressure P. 588 warning light Driver’s seat belt reminder light P. 591 Malfunction indicator lamp Front passenger’s seat belt reminder light P. 591 or P. 588 SRS warning light P. 588 Open door warning light P.
What to do if... Rear differential lock indiP. 588 cator light*2 Center differential lock indicator light*2 P. 588 Slip indicator Multi-terrain Select indicator light*3 P. 588 P. 588 Four-wheel drive indicaP. 588 tor light*2 Automatic running boards indicator light*1 P. 588 Low speed four-wheel drive P. 588 indicator light*2 *1: The light flashes to indicate a malfunction. *2: The light flashes rapidly to indicate a malfunction. *3: The light flashes continuously to indicate a malfunction.
GAS STATION INFORMATION Auxiliary catch lever P. 519 Fuel filler door P. 109 CTHPIAS103 Tire inflation pressure P. 643 Hood lock release lever P. 519 Fuel tank capacity (Reference) Fuel type 23.0 gal. (87.0 L, 19.1 Imp. gal.) Unleaded gasoline only Cold tire inflation pressure Engine oil capacity (Drain and refill ⎯ reference) With filter Without filter Engine oil type P. 636 P. 643 6.6 qt. (6.2 L, 5.5 Imp. qt.) 6.0 qt. (5.7 L, 5.0 Imp. qt.
